Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Supermicro H12SSW-iN
Summary of Contents for Supermicro H12SSW-iN
- Page 1 H12SSW- H12SSW-NT USER’S MANUAL Revision 1.0b...
- Page 2 State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all claims will not exceed the price paid for the hardware product.
- Page 3 About This Manual This manual is written for system integrators, IT technicians and knowledgeable end users. It provides information for the installation and use of the H12SSW-iN/NT motherboard. About This Motherboard Built upon the functionality and capability of the AMD EPYC® 7002/7003* series processor, the H12SSW-iN/NT motherboard provides a high performance, expandable solution while consuming little power.
- Page 4 H12SSW-iN/NT Motherboard User's Manual Contacting Supermicro Headquarters Address: Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Website: www.supermicro.com Europe Address: Super Micro Computer B.V.
-
Page 5: Table Of Contents
Preface Table of Contents Chapter 1 Introduction 1.1 Checklist ..........................8 1.1 Quick Reference .........................11 Quick Reference Table ......................12 Motherboard Features .......................14 1.2 Processor and Chipset Overview ..................17 1.3 Special Features ........................17 Recovery from AC Power Loss ..................17 1.4 System Health Monitoring ....................17 Onboard Voltage Monitors ....................18 Fan Status Monitor with Firmware Control ...............18 Environmental Temperature Control .................18... - Page 6 H12SSW-iN/NT Motherboard User's Manual Front Control Panel Pin Definitions ...................37 2.7 Connectors .........................40 2.8 Jumper Settings .........................45 How Jumpers Work ......................45 2.9 LED Indicators ........................47 Chapter 3 Troubleshooting 3.1 Troubleshooting Procedures ....................49 Before Power On ......................49 No Power ..........................49 No Video ...........................50 System Boot Failure ......................50...
- Page 7 Preface Appendix A Software Installation A.1 Installing Software Programs .....................90 A.2 SuperDoctor 5 ........................91 ® Appendix B Standardized Warning Statements B.1 Battery Handling .........................92 B.2 Product Disposal .........................94 Appendix C UEFI BIOS Recovery C.1 Overview ..........................95 C.2 Recovering the UEFI BIOS Image ..................95 C.3 Recovering the BIOS Block with a USB Device ..............95...
-
Page 8: Chapter 1 Introduction
Introduction Congratulations on purchasing your computer motherboard from an industry leader. Supermicro motherboards are designed to provide you with the highest standards in quality and performance. In addition to the motherboard, several important parts that are included with the system are listed below. - Page 9 Chapter 1: Introduction Figure 1-1. H12SSW-iN/NT Image Note: All graphics shown in this manual were based upon the latest PCB revision available at the time of publication of the manual. The motherboard you received may or may not look exactly the same as the graphics shown in this manual.
- Page 10 H12SSW-iN/NT Motherboard User's Manual JCOM1 1 2 3 UID-SW USB2/3 (3.0) :OH-LED JSXB2 JOH1 JPL1 IPMI_LAN JFPGA_SW1 JPG1:VGA 1-2:ENABLE JNCSI1 2-3:DISABLE JPB1:BMC 1-2:ENABLE 2-3:DISABLE M.2-HC2 ACT LED13 USB4(3.0) LED12 M.2-HC2 CPU PCI_E 4.0 X2 BATTERY JUSBA1 M.2-HC1 ACT LED10 CPU PCI-E 4.0 X4/X2 M.2-HC1...
-
Page 11: Quick Reference
JUSBA1 M.2-HC1 ACT LED10 CPU PCI-E 4.0 X4/X2 M.2-HC1 M.2-C1 BUZZER MH17 JBT1 JWD1 LED 11 MH15 BAR CODE H12SSW-iN SXB1C MAC CODE SXB1C USB 5/6 (3.0) NVME 4/5 SATA 8-15 NVME 2/3 JSLIM2 SATA 0-7 JPWR1 JVRM1 JPWR2 NVME 0/1... -
Page 12: Quick Reference Table
H12SSW-iN/NT Motherboard User's Manual Quick Reference Table Jumper Description Default Setting UID SW Unit ID switch (push-button toggle switch ON/OFF) JBT1 Clear CMOS Open (Normal) JWD1 Watch Dog Timer control Pins 1-2 (Reset) JPL1 LAN Enable/Disable (H12SSW-NT only) Pins 1-2 (Enabled) - Page 13 Chapter 1: Introduction Connector Description M.2-C1, M.2-C2 M.2 Slots PWRI2C Power supply SMBus I2C header JIPMB1 4-pin External BMC I2C Header (for an IPMI Card) LAN1, LAN2 Back panel LAN1, LAN2 connectors Back panel VGA port NVMe0~5 NVMe slots 0~5 Note: Note: Jumpers, connectors, switches, and LED indicators that are not described in the Jumpers, connectors, switches, and LED indicators that are not described in the...
-
Page 14: Motherboard Features
M.2 Key: M-Key Network • ATEN IPMI from ASPEED AST 2500 BMC for gigabit RJ45 port • Two RJ45 1GbE LAN ports, H12SSW-iN(1GbE Broadcom 5720L); H12SSW-NT(10GbE Broadcom 57416) Graphics • ASPEED AST2500 BMC chip with one VGA port I/O Devices •... - Page 15 Chapter 1: Introduction Features Power Management • ACPI power management (S5) • Power button override mechanism • Power-on mode for AC power recovery System Health Monitoring • Onboard voltage monitoring for +1.8V, 3.3V, +5V, +12V, +3.3V Standby, +5V Standby, VBAT, HT, Memory •...
- Page 16 H12SSW-iN/NT Motherboard User's Manual H12SSW AMD SP3 Rome Rev. 1.00 Rear I/O MLAN USB3.0 X 2 ID LED ID SW COM1 USB3.0 X 2 LAN1 LAN2 Rear 10Gb LAN 10Gb LAN IPMI LAN USB 3.0 SXB1 SXB2 RJ45 RJ45 RJ45...
-
Page 17: Processor And Chipset Overview
• System Management Bus (SMBus) Specification Version 2.0 1.3 Special Features This section describes the health monitoring features of the H12SSW-iN/NT. The motherboard has an onboard System Hardware Monitor chip that supports system health monitoring. Recovery from AC Power Loss The Basic I/O System (BIOS) provides a setting that determines how the system will respond when AC power is lost and then restored to the system. -
Page 18: Onboard Voltage Monitors
H12SSW-iN/NT Motherboard User's Manual Onboard Voltage Monitors The onboard voltage monitor will continuously scan crucial voltage levels. Once a voltage becomes unstable, it will give a warning or send an error message to the screen. Users can adjust the voltage thresholds to define the sensitivity of the voltage monitor. Real time readings of these voltage levels are all displayed in BMC. -
Page 19: Power Supply
Chapter 1: Introduction 1.6 Power Supply As with all computer products, a stable power source is necessary for proper and reliable operation. It is even more important for processors that have high CPU clock rates. In areas where noisy power transmission is present, you may choose to install a line filter to shield the computer from noise. -
Page 20: Chapter 2 Installation
H12SSW-iN/NT Motherboard User's Manual Chapter 2 Installation 2.1 Static-Sensitive Devices Electrostatic Discharge (ESD) can damage electronic com ponents. To prevent damage to your motherboard, it is important to handle it very carefully. The following measures are generally sufficient to protect your equipment from ESD. -
Page 21: Motherboard Installation
Chapter 2: Installation 2.2 Motherboard Installation All motherboards have standard mounting holes to fit different types of chassis. Make sure that the locations of all the mounting holes for both the motherboard and the chassis match. Although a chassis may have both plastic and metal mounting fasteners, metal ones are highly recommended because they ground the motherboard to the chassis. - Page 22 H12SSW-iN/NT Motherboard User's Manual Figure 2-1. Motherboard Mounting Holes...
-
Page 23: Installing The Motherboard
Chapter 2: Installation Installing the Motherboard 1. Install the I/O shield into the back of the chassis. 2. Locate the mounting holes on the motherboard. See the previous page for the locations. 3. Locate the matching mounting holes on the chassis. Align the mounting holes on the motherboard with the mounting holes on the chassis. -
Page 24: Processor And Heatsink Installation
CPU socket cap is in place and none of the socket pins are bent; otherwise, contact your retailer immediately. • Refer to the Supermicro website for updates on CPU support. Installing the Processor and Heatsink 1. Unscrew the screws holding down Force Frame in the sequence of 3-2-1. The screws are numbered on the force frame next to each screw hole. - Page 25 Chapter 2: Installation 2. The spring-loaded force frame will raise up after the last screw securing it (#1) is removed. Gently allow it to lift up to its stopping position. 3. Lift the rail frame up by gripping the lift tabs near the front end of the rail frame. While keeping a secure grip of the rail frame, lift it to a position so you can do the next step of removing the external cap.
- Page 26 H12SSW-iN/NT Motherboard User's Manual 4. Remove the external cap from the Rail Frame by pulling it upwards through the rail guides on the rail frame. External Cap PnP Cover Cap 5. The CPU package is shipped from the factory with the blue carrier frame pre-assembled.
- Page 27 Chapter 2: Installation Note: You can only install the CPU inside the socket in one direction with the handle at the top. Make sure that it is properly inserted into the CPU socket before closing the rail frame plate. If it doesn't close properly, do not force it as it may damage your CPU. Instead, open the rail frame plate again, and double-check that the CPU is aligned properly.
- Page 28 H12SSW-iN/NT Motherboard User's Manual 9. Gently lower the force frame down onto the rail frame and hold it in place until it is seated in the Socket housing. Note that the force frame is spring loaded and has to be held in place before it is secured.
- Page 29 Chapter 2: Installation 11. After the force frame is secured and the CPU package is in place, now you must install the heatsink to the frame. Lower the heatsink down till it rests securely over the four screw holes on CPU package on the socket frame. 12.
- Page 30 H12SSW-iN/NT Motherboard User's Manual Uninstalling the Processor and Heatsink 1. Remove the heatsink attached to the top of the CPU package by reversing the installation procedure. 2. Clean the Thermal grease left by the heatsink on the CPU package lid to limit the risk of it contaminating the CPU package land pads or contacts in the socket housing.
-
Page 31: Memory Support And Installation
Important: Exercise extreme care when installing or removing DIMM modules to prevent any possible damage. Memory Support The H12SSW-iN/NT supports up to 2TB of ECC DDR4 3200MHz speed, RDIMM/LRDIMM/3DS/ NVDIMM memory in eight slots. Refer to the table below for additional memory information. Populating RDIMM/RDIMM 3DS/LRDIMM/LRDIMM 3DS DDR4 Memory Modules... -
Page 32: Dimm Module Population
JPL1 IPMI_LAN H12SSW-iN/NT Motherboard User's Manual JFPGA_SW1 JPG1:VGA 1-2:ENABLE JNCSI1 2-3:DISABLE DIMM Module Population JPB1:BMC 1-2:ENABLE When populating the motherboard with DIMM modules, please keep in mind the following: 2-3:DISABLE M.2-HC2 ACT LED13 USB4(3.0) • Always use DDR4 DIMM modules of the same type, size and speed. -
Page 33: Dimm Installation
Chapter 2: Installation DIMM Installation 1. Insert the desired number of DIMMs into the memory slots, there is no specific sequence or order required Receptive 2. Push the release tabs outwards on both Point ends of the DIMM slot to unlock it. 3. -
Page 34: Rear I/O Ports
H12SSW-iN/NT Motherboard User's Manual 2.5 Rear I/O Ports See Figure below for the locations and descriptions of the various I/O ports on the rear of the motherboard. JCOM1 1 2 3 UID-SW USB2/3 (3.0) :OH-LED JSXB2 JOH1 JPL1 IPMI_LAN JFPGA_SW1... - Page 35 See page 36 for the front panel UID LED header location on JF1. Note: UID can also be triggered via IPMI on the serverboard. For more information on IPMI, please refer to the IPMI User's Guide posted on our website at http://www.supermicro.com...
-
Page 36: Front Control Panel
JF1 contains header pins for various buttons and indicators that are normally located on a control panel at the front of the chassis. These connectors are designed specifically for use with Supermicro chassis. See the figure below for the location of JF1.. JCOM1... -
Page 37: Front Control Panel Pin Definitions
Chapter 2: Installation Front Control Panel Pin Definitions NMI Button The non-maskable interrupt button header is located on pins 19 and 20 of JF1. Refer to the table below for pin definitions. NMI Button Pin Definitions (JF1) Pin# Definition Control Ground Power LED The Power LED connection is located on pins 15 and 16 of JF1. - Page 38 H12SSW-iN/NT Motherboard User's Manual NIC1/NIC2 Link LED The NIC (Network Interface Controller) LED connection for LAN port 1 is located on pins 11 and 12 of JF1, and the LED connection for LAN Port 2 is on Pins 9 and 10. Attach the NIC LED cables to display network activity.
- Page 39 Chapter 2: Installation Reset Button The Reset Button connection is located on pins 3 and 4 of JF1. Attach the hardware reset switch from the computer case to this header to reset the system. Refer to the table below for pin definitions. Reset Button Pin Definitions (JF1) Pin#...
-
Page 40: Connectors
SATA ports. See the table below for pin definitions. DOM Power Pin Definitions Pin# Definition Ground Ground SATA (SATA0, SATA1) The H12SSW-iN/NT has two available SATA 3.0 ports (SATA0 and SATA1) on the motherboard. These are standard SATA 3.0 ports. SATA Connectors Pin Definitions Pin# Signal Ground SATA_TXP... - Page 41 Chapter 2: Installation NVMe Ports ( NVMe 0/1) The H12SSW-iN/NT has two dedicated NVMe ports (two ports on a slim SAS connector) on the motherboard. These ports provide high-speed, low-latency PCIe 3.0 x4 connections directly from the CPU to NVMe Solid State (SSD) drives. This greatly increases SSD data- throughput performance and significantly reduces PCIe latency by simplifying driver/software requirements resulting from direct PCIe interface from the CPU to the NVMe SSD drives.
- Page 42 H12SSW-iN/NT Motherboard User's Manual USB Ports (USB 0~3, USB 4, USB 5/6) There are a total of seven USB ports supported on the motherboard. Four are located on the back panel , USB 0/1, and USB 2/3 (both are USB 3.1 compliant). There are also three ports located on the motherboard, two are on one header, USB 5/6 (3.1) and the remaining...
- Page 43 Chapter 2: Installation Chassis Intrusion (JL1) A Chassis Intrusion header is located at JL1 on the motherboard. Attach the appropriate cable from the chassis to the header to inform you when the chassis is opened. Chassis Intrusion Pin Definitions Pins Definition Ground Intrusion Input...
- Page 44 H12SSW-iN/NT Motherboard User's Manual Main Power Supply Connector (JPWR2) The primary power supply connector (JPWR2) is an ATX power connector that the power supply plugs into directly. ATX Power 24-pin Connector Pin Definitions Pin# Definition Pin # Definition +3.3V +3.3V -12V +3.3V...
-
Page 45: Jumper Settings
Chapter 2: Installation 2.8 Jumper Settings How Jumpers Work To modify the operation of the motherboard, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector. Pin #1 is identified with a thicker border line on the printed circuit board. See the diagram below for an example of jumping pins 1 and 2. - Page 46 H12SSW-iN/NT Motherboard User's Manual Watch Dog (JWD1) JWD1 controls the Watch Dog function. Watch Dog is a monitor that can reboot the system when a software application hangs. Jumping pins 1-2 will cause Watch Dog to reset the system if an application hangs. Jumping pins 2-3 will generate a non-maskable interrupt signal for the application that hangs.
-
Page 47: Led Indicators
The Link LED may be green, orange/amber, or off to indicate the speed of the connection. Refer to the tables below for more information. H12SSW-NT H12SSW-iN Link LED, Connection Link, Speed Link LED, Connection Link, Speed... - Page 48 H12SSW-iN/NT Motherboard User's Manual Onboard Power OK LED (LED6) LED6 is an onboard power OK LED. When this LED6 is lit, it means the system is turned on, and all the system power rails are ready. When the system is turned off, or any one of the system power rails fail, this LED will turn off.
-
Page 49: Chapter 3 Troubleshooting
Chapter 3: Troubleshooting Chapter 3 Troubleshooting 3.1 Troubleshooting Procedures Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and still need assistance, refer to the ‘Technical Support Procedures’ and/ or ‘Returning Merchandise for Service’ section(s) in this chapter. Always disconnect the AC power cord before adding, changing or installing any non hot-swap hardware components. -
Page 50: No Video
H12SSW-iN/NT Motherboard User's Manual No Video 1. If the power is on but you have no video, remove all the add-on cards and cables. 2. Check if memory module population is supported following guidelines on page 31, and re-seat memory DIMM module(s). -
Page 51: When The System Becomes Unstable
2. Memory support: Make sure that the memory modules are supported by testing the modules using memtest86 or a similar utility. Note: Refer to the product page on our website at http:\\www.supermicro.com for memory and CPU support and updates. 3. HDD support: Make sure that all hard disk drives (HDDs) work properly. Replace the bad HDDs with good ones. -
Page 52: Technical Support Procedures
H12SSW-iN/NT Motherboard User's Manual 4. Identifying bad components by isolating them: If necessary, remove a component in question from the chassis, and test it in isolation to make sure that it works properly. Replace a bad component with a good one. -
Page 53: Frequently Asked Questions
3.3 Frequently Asked Questions Question: What type of memory does my motherboard support? Answer: The H12SSW-iN/NT motherboard supports up to 2TB of ECC DDR4 2933/3200 MHz speed, RDIMM/LRDIMM/3DS/NVDIMM memory in eight slots. See Section 2.4 for details on installing memory. - Page 54 H12SSW-iN/NT Motherboard User's Manual Question: When I run setup.exe to install AMD SP3 I/O drivers under windows, the Installshield wizard shows “Unable to save file: C:\AMD\AMD_Chipset_Drivers\..The system cannot find the path specified”. Answer: This happens under specific environments. Please click “ok”, and Installshield will prompt you to save the drivers to a folder you designate.
-
Page 55: Returning Merchandise For Service
Shipping and handling charges will be applied for all orders that must be mailed when service is complete. For faster service, RMA authorizations may be requested online (http://www.supermicro.com/ support/rma/). This warranty only covers normal consumer use and does not cover damages incurred in shipping or from failure due to the alteration, misuse, abuse or improper maintenance of products. -
Page 56: Battery Removal
H12SSW-iN/NT Motherboard User's Manual Battery Removal To remove the onboard battery, follow the steps below: 1. Power off your system and unplug your power cable. 2. Locate the onboard battery as shown below. 3. Using a tool such as a pen or a small screwdriver, push the battery lock outwards to unlock it. -
Page 57: Chapter 4 Uefi Bios
UEFI BIOS 4.1 Introduction This chapter describes the AMIBIOS™ Setup utility for the H12SSW-iN/NT motherboard. The BIOS is stored on a chip and can be easily upgraded using a flash program. Note: Due to periodic changes to the BIOS, some settings may have been added or deleted and might not yet be recorded in this manual. -
Page 58: Main Setup
H12SSW-iN/NT Motherboard User's Manual 4.2 Main Setup When you first enter the AMI BIOS setup utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab on the top of the screen. The Main BIOS setup screen is shown below. - Page 59 Chapter 4: UEFI BIOS Build Date This item displays the date when the version of the BIOS ROM used in the system was built. CPLD Version This item displays the CPLD version of the BIOS ROM used in the system. Memory Information Total Memory This feature displays the total system memory detected.
-
Page 60: Advanced
H12SSW-iN/NT Motherboard User's Manual 4.3 Advanced Use the arrow keys to select a top item and press <Enter> to access the submenu items. Warning: Take caution when changing the Advanced settings. An incorrect value, a very high DRAM frequency, or an incorrect DRAM timing setting may make the system unstable. - Page 61 Chapter 4: UEFI BIOS Bootup NumLock State Use this feature to set the Power on state for the <Numlock> key. The options are Off and On. Wait For "F1" If Error Use this feature to force the system to wait until the 'F1' key is pressed if an error occurs. The options are Disabled and Enabled.
- Page 62 H12SSW-iN/NT Motherboard User's Manual Trusted Computing Security Device Support If this feature and the TPM jumper on the motherboard are both set to Enabled, onboard security devices will be enabled for TPM (Trusted Platform Module) support to enhance data integrity and network security.
- Page 63 Chapter 4: UEFI BIOS ACPI Settings High Precision Event Timer The High Precision Event Timer (HPET) can produce periodic interrupts and is used to synchronize multimedia streams, providing smooth playback and reducing the need to use other timestamp calculations. The options are Enabled and Disabled. NUMA Nodes Per Socket This feature specifies the number of desired Non-Uniform Memory Access (NUMA) nodes per socket.
- Page 64 H12SSW-iN/NT Motherboard User's Manual Change Settings This feature specifies the base I/O port address and the Interrupt Request address of a serial port specified by the user. Select Auto to allow the BIOS to automatically assign the base I/O and IRQ address. The options are Auto, (IO=2F8h; IRQ=3;); (IO=3F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12;);...
- Page 65 Chapter 4: UEFI BIOS as a parity bit to be sent along with the data bits. Select Space to add a Space as a parity bit to be sent with your data bits. The options are None, Even, Odd, Mark, and Space. Stop Bits A stop bit indicates the end of a serial data packet.
- Page 66 H12SSW-iN/NT Motherboard User's Manual and function key support. Select ANSI to use the Extended ASCII Character Set. Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or more bytes. The options are VT100, VT100+, VT-UTF8, and ANSI.
- Page 67 Chapter 4: UEFI BIOS Putty KeyPad This feature selects the settings for Function Keys and KeyPad used for Putty, which is a terminal emulator designed for the Windows OS. The options are VT100, LINUX, XTERMR6, SC0, ESCN, and VT400. Legacy Console Redirection Legacy Console Redirection Settings Redirection COM Port For this setting, select a COM port to display redirection of Legacy OS and Legacy OPROM...
- Page 68 H12SSW-iN/NT Motherboard User's Manual UTF8 encoding to map Unicode characters into one or more bytes. The options are VT100, VT100+, VT-UTF8, and ANSI. Bits per Second This item sets the transmission speed for a serial port used in Console Redirection. Make sure that the same speed is used in the host computer and the client computer.
- Page 69 Chapter 4: UEFI BIOS SVM Mode This setting Enables or Disables CPU Virtualization. CPU Information These sections are for informational purposes. They will display some details about the detected CPUs on the motherboard, such as: • CPU Version • Number of Cores Running •...
- Page 70 H12SSW-iN/NT Motherboard User's Manual Memory Interleaving This setting controls fabric level memory interleaving. Note that the channel, die and socket have requirements on memory populations and it will be ignored if the memory doesn't support the selected option. The options are Disabled and Auto.
- Page 71 Chapter 4: UEFI BIOS ARI Forwarding If supported by the hardware and set to 'enabled', the downstream port disables its traditional device number field, being 0 enforcement, when turning a type1 configuration request into a type0 configuration request. This permits access to extended functions in an ARI device immediately below the port.
- Page 72 H12SSW-iN/NT Motherboard User's Manual Onboard LAN2 Option ROM Use this setting to select which firmware function is to be loaded for onboard LAN2 on the system. Options include Disabled and PXE. Onboard Video Option ROM Use this setting to select which firmware function is to be loaded for onboard LAN2 on the system.
- Page 73 Chapter 4: UEFI BIOS USB Configuration Legacy USB Support Select Enabled to support onboard legacy USB devices. Select Auto to disable legacy support if there are no legacy USB devices present. Select Disable to have all USB devices available for EFI applications only. The options are Enabled, Disabled and Auto. XHCI Hand-Off This is a work-around solution for operating systems that do not support XHCI (Extensible Host Controller Interface) hand-off.
- Page 74 H12SSW-iN/NT Motherboard User's Manual SATA Configuration SATA Enable This item enables or disables the onboard SATA controller supported by the Intel PCH chip. The options are Enabled and Disabled. SATA Hotplug This item enables or disables the onboard SATA controller's hot plug feature (PCH). The options are Enabled and Disabled.
- Page 75 Chapter 4: UEFI BIOS Network Configuration (Available when EFI is selected in LAN OPROM after reboot, page 71) VLAN Configuration (LAN1 and LAN2) Enter Configuration Menu Create New VLAN VLAN ID This option is an input field used to enter a unique numeric VLAN ID. The valid range is from 0~4096.
- Page 76 H12SSW-iN/NT Motherboard User's Manual Local IP Address This item sets and displays the Local IP address for this computer. This should be in decimal and in dotted quad form. Local Net Mask This item sets the sub-network that this computer belongs to. The value of each three-digit number separated by dots should not exceed 255.
- Page 77 Chapter 4: UEFI BIOS iSCSI Configuration iSCSI Initiator Name This feature allows the user to enter the unique name of the iSCSI Initiator in IQN format. Once the name of the iSCSI Initiator is entered into the system, configure the proper settings for the following items.
-
Page 78: Ipmi
H12SSW-iN/NT Motherboard User's Manual 4.4 IPMI This tab allows you to configure the following IPMI settings for the system. Use this feature to configure Intelligent Platform Management Interface (IPMI) settings. BMC Firmware Revision This item indicates the IPMI firmware revision used in your system. - Page 79 Chapter 4: UEFI BIOS Erasing Settings Erase SEL Select Yes, On next reset to erase all system event logs upon next system reboot. Select Yes, On every reset to erase all system event logs upon each system reboot. Select No to keep all system event logs after each system reboot.
- Page 80 H12SSW-iN/NT Motherboard User's Manual Station IP Address This item displays the Station IP address for this computer. This should be in decimal and in dotted quad form. Subnet Mask This item displays the sub-network that this computer belongs to. The value of each three- digit number separated by dots should not exceed 255.
-
Page 81: Event Logs
Chapter 4: UEFI BIOS 4.5 Event Logs This tab allows the user to configure the following event logs settings for the system. Change SMBIOS Event Log Settings This feature allows the user to configure SMBIOS Event settings. Enabling/Disabling Options SMBIOS Event Log Select Enabled to enable SMBIOS (System Management BIOS) Event Logging during system boot. - Page 82 H12SSW-iN/NT Motherboard User's Manual When Log is Full Select Erase Immediately to immediately erase all errors in the SMBIOS event log when the event log is full. Select Do Nothing for the system to do nothing when the SMBIOS event log is full. The options are Do Nothing and Erase Immediately.
-
Page 83: Security
Chapter 4: UEFI BIOS 4.6 Security This tab allows you to configure the following security settings for the system. Administrator Password Press Enter to create a new, or change an existing Administrator password. Note that if the Administrator Password is erased, the User Password will be cleared as well. User Password Press Enter to create a new, or change an existing User password. - Page 84 H12SSW-iN/NT Motherboard User's Manual Secure Boot This option allows you specify when the Platform Key (PK) is enrolled. When enabled, the System Mode is user deployed, and the CSM function is disabled. Options include Enabled and Disabled. Secure Boot Mode Use this item to select the secure boot mode.
- Page 85 Chapter 4: UEFI BIOS Append Key Select Yes to add the KEK from the manufacturer's defaults list to the existing KEK. Select No to load the KEK from a file. The options are Yes and No. Authorized Signatures Set New Key Select Yes to load the database from the manufacturer's defaults.
-
Page 86: Boot
H12SSW-iN/NT Motherboard User's Manual 4.7 Boot Use this tab to configure Boot Settings: Boot Mode Select Use this item to select the type of device that the system is going to boot from. The options are LEGACY, UEFI, and DUAL. The default setting is DUAL. - Page 87 Chapter 4: UEFI BIOS UEFI Application Boot Priorities This feature allows the user to specify which UEFI devices are boot devices. • UEFI Boot Order #1 NETWORK Drive BBS Priorities This feature allows the user to specify which UEFI network drive devices are boot devices.
-
Page 88: Save & Exit
H12SSW-iN/NT Motherboard User's Manual 4.8 Save & Exit Select the Save & Exit tab to enter the Save & Exit BIOS Setup screen. Discard Changes and Exit Select this option to quit the BIOS Setup without making any permanent changes to the system configuration, and reboot the computer. - Page 89 Chapter 4: UEFI BIOS Default Options Restore Defaults To set this feature, select Restore Defaults from the Save & Exit menu and press <Enter>. These are factory settings designed for maximum system stability, but not for maximum performance. Save as User Defaults To set this feature, select Save as User Defaults from the Exit menu and press <Enter>.
- Page 90 USB/SATA DVD drive, or a USB flash drive, or the IPMI KVM console. 2. Retrieve the proper RST/RSTe driver. Go to the Supermicro web page for your motherboard and click on "Download the Latest Drivers and Utilities", select the proper driver, and copy it to a USB flash drive.
-
Page 91: Appendix A Software Installation
Appendix A: Software 4. During Windows Setup, continue to the dialog where you select the drives on which to install Windows. If the disk you want to use is not listed, click on “Load driver” link at the bottom left corner. Figure A-2. - Page 92 The Supermicro website contains drivers and utilities for your system at https://www. supermicro.com/wdl/driver. Some of these must be installed, such as the chipset driver. After accessing the website, go into the CDR_Images (in the parent directory of the above link) and locate the ISO file for your motherboard. Download this file to to a USB flash drive or a DVD.
-
Page 93: Superdoctor 5
A.3 SuperDoctor ® The Supermicro SuperDoctor 5 is a program that functions in a command-line or web-based interface for Windows and Linux operating systems. The program monitors such system health information as CPU temperature, system voltages, system power consumption, fan speed, and provides alerts via email or Simple Network Management Protocol (SNMP). -
Page 94: Appendix B Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user of situations which have the potential for bodily injury. Should you have questions or experience difficulty, contact Supermicro's Technical Support department for assistance. Only certified technicians should attempt to install or configure components. - Page 95 Appendix B: Standardized Warning Statements Attention Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par une pile de type semblable ou équivalent, recommandée par le fabricant. Jeter les piles usagées conformément aux instructions du fabricant. ¡Advertencia! Existe peligro de explosión si la batería se reemplaza de manera incorrecta.
-
Page 96: Product Disposal
H12SSW-iN/NT Motherboard User's Manual B.2 Product Disposal Warning! Ultimate disposal of this product should be handled according to all national laws and regulations. 製品の廃棄 この製品を廃棄処分する場合、 国の関係する全ての法律 ・ 条例に従い処理する必要があります。 警告 本产品的废弃处理应根据所有国家的法律和规章进行。 警告 本產品的廢棄處理應根據所有國家的法律和規章進行。 Warnung Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes erfolgen. -
Page 97: Appendix C Uefi Bios Recovery
Warning: Do not upgrade the BIOS unless your system has a BIOS-related issue. Flashing the wrong BIOS can cause irreparable damage to the system. In no event shall Supermicro be liable for direct, indirect, special, incidental, or consequential damages arising from a BIOS update. - Page 98 USB flash drive with FAT16 or FAT32 format and rename the file to SUPER.ROM. Note: If you cannot locate the "SUPER.ROM" file in your driver disk, visit our website at www.supermicro.com to download the correct BIOS image into a USB flash device and rename it "SUPER.ROM".
- Page 99 SUPERMICO BIOS Update: https://www.youtube.com/watch?v=S8z6iOEHGwY * If the BIOS flash recovery fails, contact our RMA Department to have the BIOS chip reprogrammed. This will require shipping the board to Supermicro for repair. Submit your RMA request at https://www.supermicro.com/support/rma Please make sure to follow all instructions when returning the motherboard.