Download Print this page
D-Link DFL-500 Quick Install Manual
D-Link DFL-500 Quick Install Manual

D-Link DFL-500 Quick Install Manual

Hide thumbs Also See for DFL-500:

Advertisement

Quick Links

1. Before you start
The DFL-500 has the following settings when first powered on.
Operating Mode:
Administrator Account:
Internal Interface:
External Interface:
Use the following table to gather the information you need to customize basic settings for your DFL-
500.
Administrator Password:
Internal Interface:
External Interface:
Internal Server
Settings:
User name:
Password:
IP:
Netmask:
Manual:
IP:
Netmask:
Default Gateway:
Primary DNS Server:
Secondary DNS Server: 207.194.200.129
IP:
Netmask:
Manual:
IP:
Netmask:
Default Gateway:
Primary DNS Server:
Secondary DNS
Server:
Web Server:
Mail Server: SMTP:
FTP Server:
If you provide access from the Internet to a web server, mail server, or FTP
server installed on an internal network, add the IP addresses of the servers
here.
Quick Install Guide
NAT/Route
admin
(none)
192.168.1.99
255.255.255.0
192.168.100.99
255.255.255.0
(none)
207.194.200.1
_____._____._____._____
_____._____._____._____
_____._____._____._____
_____._____._____._____
_____._____._____._____
_____._____._____._____
_____._____._____._____
_____._____._____._____
_____._____._____._____
_____._____._____._____
POP3:
_____._____._____._____
DFL-500
Version 2.27

Advertisement

loading

Summary of Contents for D-Link DFL-500

  • Page 1 Quick Install Guide DFL-500 Version 2.27 1. Before you start The DFL-500 has the following settings when first powered on. NAT/Route Operating Mode: Administrator Account: User name: admin Password: (none) Internal Interface: 192.168.1.99 Netmask: 255.255.255.0 External Interface: Manual: 192.168.100.99 Netmask: 255.255.255.0...
  • Page 2: Advanced Settings

    2. Advanced settings Use the following table to gather the information you need to customize advanced DFL-500 settings that can be configured using the setup wizard. External DHCP: If your ISP supplies you with an IP address using DHCP no further Interface: information is required.
  • Page 3: Using The Firewall Setup Wizard

    2. Connect the AC adapter to the power connection at the back of the DFL-500. 3. Connect the AC adapter to a power outlet. The DFL-500 starts up. The Power and Status lights light. The Status light flashes while the DFL-500 is starting up and remains lit when the system is up and running.
  • Page 4 DFL-500. To use the CLI: 1. Connect one end of the null-modem cable to the DFL-500 Console (RS-232 serial) connector and connect the other end to a serial port of a management computer or terminal. 2. On the management computer, start a terminal program such as HyperTerminal.
  • Page 5 9. Set the default route to the Default Gateway IP address. For example to set the default route to 204.23.1.2 enter: set system route add 0.0.0.0 0.0.0.0 gw 204.23.1.2 dev external Once these addresses are set, you are ready to connect the DFL-500 to your network.
  • Page 6: Advanced Configuration

    Provider. 9. Advanced configuration You have completed the basic network setup of your DFL-500. By default all traffic originating from your Internal network is allowed to reach the Internet, and all traffic originating from the Internet is blocked from reaching your internal network.
  • Page 7: 10. Troubleshooting

    IP address of the management computer to be on the same subnet as the internal interface. Restarting the DFL-500 At any time during the installation process if the DFL-500 is not responding correctly, you can shut it down and restart it.
  • Page 8 Enter the command. execute reboot You can cycle the power on the DFL-500 using the power switch on the back of the unit. Resetting the DFL-500 to the factory default configuration If restarting does not solve the problem, you can restore the DFL-500 to its factory default configuration.