Auto Install; Basic Tv And Remote Control Operation - Magnavox MT1331B Owner's Manual

A I
UTO NSTALL
F ollow these steps to quickly
add area channels into the
TV's memory. Before you
begin, make sure batteries are
in the remote control and you
are familiar with the remote.
Details are provided below.
SLEEP
POWER
1 2 3
4 5 6
7 8 9
STATUS/EXIT
ALT.CH
0
MUTE
MENU
CH.
VOL. VOL.
CH.
R
EMOTE
T o load the batteries into the
remote:
1. Press in the tab on the
battery compartment
lid on the bottom of the
remote control, then lift
off the lid.
2. Insert two AA batter-
ies (supplied) into the
battery compartment
as indicated inside the
compartment. Installing
batteries incorrectly may
damage the remote
control.
3. Replace the lid.
Battery
Compartment
Lid
STATUS/EXIT Button
Press to see the current channel number on the
TV screen.
Battery
Press to remove the on-screen menu. You also
Compartment
may remove the menu by pressing the
CH(annel) L/M buttons to select EXIT, then
pressing the VOL(ume) B/{ buttons. (You
may need to select EXIT repeatedly to com-
pletely remove all of the menus.)
T
ELEVISION
EARPHONE MENU VOLUME CHANNEL POWER
Note:
You can connect earphones (not supplied) to the EARPHONE
jack on the front of the TV for private, personal listening.
S U
ETTING
Press the POWER
button to turn on the TV.
Point the remote control
toward the remote sensor on the TV
when operating the TV with the remote.
(See Television illustration below.)
SLEEP Button
Press to set the TV to turn itself off
automatically. Details are on page 5.
Number Buttons
Press to select channels.
• Cable Users
Enter channel numbers as a two-digit number for
the quickest results. For example, to select chan-
nel 6, press 0,6. Pressing only Number button 6
will cause a brief delay. (There also may be a
brief delay when you select channels 10, 11, and
12.) For channels 100 and above, enter three-
digit numbers. For example, to select channel
117, press 1, 1, 7.
• Antenna Users
Enter channel numbers as a two-digit number for
the quickest results. For example, to select chan-
nel 5, press 0,5. Pressing only the Number 5 but-
ton will cause a delay in selecting channel 5. Only
channels 2-69 are available.
Press the POWER
button to turn on the TV.
Be sure to connect the TV
power cord to a standard
AC outlet first.
HONE MENU VOLUME CHANNEL POWER
U Y
P AND SING OUR
Press the MENU but-
ton. The main menu appears
on the TV screen.
SETUP B
EXIT B
BRIGHTNESS 24
COLOR 31
PICTURE 31
Press the CH(annel) L
or M button to select SETUP.
Then, press the VOL(ume)
B or { button to continue.
EXIT
B
LANGUAGE ENG

AUTO INSTALL

B
CHANNEL EDIT B
SLEEP
POWER
1 2 3
4 5 6
7 8 9
STATUS/EXIT ALT.CH
0
MUTE
MENU
CH.
VOL. VOL.
CH.
CC
Press the VOLUME
L/M buttons to adjust the
sound level.
Press the CHAN-
NEL L/M buttons to select
available TV channels. (See
Auto Install above.)
Remote Sensor
Point the remote
control here when
using the remote
to work the TV.
- 4 -
TV
Press the CH(annel) L or
M button to select AUTO
INSTALL. Then, press the
VOL(ume) B or { button to
enter AUTO INSTALL, which
will set up the channels.
AUTO STORE 31
When setup is complete, the
SETUP menu will reappear for
about 30 seconds, then the low-
est stored channel will appear.
Now, when you press the
CH(annel) L or M button, you
will only scan through channels
that are available. You still may
select non-memorized channels
by pressing the Number buttons.
POWER Button
Press to turn the TV on and off.
ALT. CH (Alternate Channel) Button
Press to return to the previously viewed TV
channel.
MENU Button
Press to access or remove the on-screen
menu. Press the CH(annel) L/M buttons to
select an item in the menu. Press the
VOL(ume) B/{ buttons to adjust an item in
the menu or to advance to the next menu.
MUTE Button
Press to disable the sound on the TV. Press
again to restore the sound.
VOL(ume) B/{ Buttons
Press to adjust the TV sound level. Press to
adjust an item in the on-screen menu or to
advance to the next menu.
If you press the VOL(ume) { button when
the sound is muted, the volume bar will
appear on the screen. Pressing the
VOL(ume) B button when the sound is
muted will restore the sound.
CH(annel) L/M Buttons
Press to scan through available channels.
Press to select an item in the on-screen menu.
CC (Closed Caption) Button
Press repeatedly to select a Closed Caption
mode. Details are on page 7.
Press the MENU button
to display the TV's on-screen
menu.
Press the CHANNEL L/M
buttons to select an item in the
menu.
Press the VOLUME L/M but-
tons to adjust an item in the
menu or to advance to the next
menu.
Note: To remove the menu,
press the CHANNEL L/M but-
tons to select EXIT. Then, press
the VOLUME L or M button.
(You may need to select EXIT
repeatedly to completely remove
all of the menus.)
Or, press the MENU button,
repeatedly if necessary, to
remove the MENU.
S
MART
H
ELP
Complete each
step within 30 sec-
onds of the previ-
ous step.
S
MART
H
ELP
The current
channel number
will appear briefly
when the TV is first
turned on and with
channel changes. To
display the channel
number for five
seconds, press the
STATUS/EXIT
button.
You can turn on the
TV by pressing the
CHANNEL L or M
button on the front
of the TV. The
CH(annel) L/M but-
tons of the remote
control will not turn
on the TV power.