Related Manuals for HP Metal Jet S100
Summary of Contents for HP Metal Jet S100
- Page 1 HP Metal Jet S100 Powder Removal Station Product Documentation Introductory Information SUMMARY Introductory information about your product...
- Page 2 Development Company, L.P. The information contained herein is subject Edition 1 to change without notice. The only warranties for HP products and services are set forth in the express warranty statement accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
-
Page 3: Table Of Contents
Table of contents 1 HP Metal Jet S100 Powder Removal Station Introductory Information ......................1 What is it? ................................................1 Documentation..............................................1 Safety precautions............................................1 Front panel...............................................18 System errors..............................................19 Power specifications..........................................19... -
Page 4: Hp Metal Jet S100 Powder Removal Station Introductory Information
HP Build Units according to the user-defined print job and customized parameters. Once printing and curing are complete, the build unit is manually inserted into the HP Powder Removal Station where loose powder is automatically removed from the printed parts and collected in the HP Powder Collector. - Page 5 The equipment should always be kept in the same environmental conditions. Use HP-certified and HP-branded agents only. Do not use unauthorized third-party agents. The area in which the equipment is installed should be free from liquid spillage and environmental condensation.
- Page 6 Ensure that there is no condensation inside the equipment before turning it on. Take special care with zones marked with warning labels. Use HP-certified equipment and accessories only. The use of third-party equipment and accessories can cause safety risks, powder leakages, and malfunctions in the printer; and may affect your system warranty.
- Page 7 Ground the portable tank and drums using static earthing clamps during refilling or unloading. ● HP recommends the use of HP equipment for unpacking 3D parts and refilling the build unit. If other methods are used, read the following notes: –...
- Page 8 Minimum particle size (d10) > 2 μm ● Non-reactive with other materials or HP agents (see the safety data sheets for the agents on the HP website at the following link: http://www.hp.com/go/msds), stable There is no support for the powder removal station, customers takes full responsibility for it.
- Page 9 The build chamber and curing station subsystems operate at high temperatures. Call your service representative if the built-in Residual Current Circuit Breaker (Ground Fault Circuit Interrupter) is repeatedly tripped. Chapter 1 HP Metal Jet S100 Powder Removal Station Introductory Information...
- Page 10 Do not attempt to modify the electrical cabinet, or any enclosure of the machine. ● Proper maintenance and genuine HP consumables are required to ensure that the equipment operates safely as designed. The use of non-HP consumables may present a risk of fire. ● Take special care with zones marked with warning labels.
- Page 11 Sound pressure level Declared dual number noise emission values in accordance with ISO 4871, corresponding to the worst bystander position according to ISO 11202, located at the rear of the product. Chapter 1 HP Metal Jet S100 Powder Removal Station Introductory Information...
- Page 12 Printer Sound Pressure Level measured per ISO 11202 at by-standing positions is < 70dB(A). Curing station Declared dual-number noise-emission values in accordance with ISO 4871: ● LpA = 71 dB(A) ● KpA = 5 dB Powder management The emitted sound pressure level could exceed 70dB(A) when filling the load station's input tanks. The maximum emitted sound pressure level is below 80 dB(A) (measurements according to ISO 11201).
- Page 13 Refer to the safety data sheet and meet local regulations in order to use the appropriate personal protective equipment needed, including heat and chemical resistant gloves when unpacking 3D printed parts. Chapter 1 HP Metal Jet S100 Powder Removal Station Introductory Information...
- Page 14 Personal protective equipment It is recommended to use heat and chemical resistant gloves, mask, goggles, safety conductive or dissipative footwear, safety boots, coat, conductive or dissipative clothing, and hearing protection for maintenance tasks, cleaning and powder handling. Refer to the Safety Data Sheet of the powder and agent and meet local regulations.
- Page 15 In case of unexpected malfunction, anomaly, ESD (ElectroStatic Discharges), or electromagnetic interference, press the emergency stop button and disconnect the equipment. If the problem persists, contact your support representative. Chapter 1 HP Metal Jet S100 Powder Removal Station Introductory Information...
- Page 16 Warning labels (continued) Label Explanation DANGER! Electric shock hazard Heating modules operate at hazardous voltage. Disconnect power source before servicing. CAUTION: Double pole. Neutral fusing. Refer servicing to qualified service personnel. WARNING! High leakage current. Earth connection essential before connecting supply. Equipment to be connected to earthed mains only.
- Page 17 Do not operate with guards removed, lockout/tagout before servicing. WARNING! Light radiation hazard. Light radiation. Do not stare at the top cover's light, it may be harmful to the eyes. Chapter 1 HP Metal Jet S100 Powder Removal Station Introductory Information...
- Page 18 Warning labels (continued) Label Explanation WARNING! Moving fan blades. Hazardous moving parts. Keep hands away from moving fan blades. Do not operate with guards removed, lockout/tagout before servicing. WARNING! Potentially explosive atmosphere. Combustible dust clouds or flammable vapors can form explosive mixtures with air.
- Page 19 Use of safety goggles for operating and handling machine, supplies or waste. Refer to supplies safety data sheets (SDS). CAUTION: Safety boots required. Feet striking or being struck by objects. Wear anti-static footwear. Chapter 1 HP Metal Jet S100 Powder Removal Station Introductory Information...
- Page 20 Warning labels (continued) Label Explanation WARNING! An explosion-protected vacuum cleaner certified for collection of metal combustible dust is required for cleaning. Do not sweep the dust or try to remove it with a compressed- air gun. Follow maintenance, cleaning tasks and housekeeping to ensure correct operation and safety.
-
Page 21: Front Panel
The front panel displays alerts (warning and error messages) when necessary. Chapter 1 HP Metal Jet S100 Powder Removal Station Introductory Information... -
Page 22: System Errors
Powder management station home screen Change system options You can change various system options from the front panel. System errors The front panel may occasionally display a system error, consisting of a numerical code of 12 digits followed by the recommended action that you should take. In most cases you will be asked to restart the system. - Page 23 Cross-sectional area 4 mm² 12 AWG Terminals Ferrule terminals External diameter range 8–17 mm (0.31-0.67 in) NOTE: The main disconnect and branch protection should be provided by the installer. Chapter 1 HP Metal Jet S100 Powder Removal Station Introductory Information...