Environmental Protection; Technical Data - Metabo HO 18 LTX 20-82 Instructions Manual

Clogged ejection nozzle
Use a suitable tool, e.g. a piece of wood to
clean a clogged ejection nozzle (14). Do not
reach into the ejection nozzle (14).
If the outlet nozzle (14)tends to clog often
(depending on the material and operation), we
recommend unscrewing the outlet nozzle (14) and
to attach the ejection nozzle (15). Note: The parts
(16), (17), (18) cannot be attached to the ejection
nozzle (15).
Clean the machine regularly. Remove chip
ejection adapter (18) and clean e.g. with a cloth.
Vacuum clean the ventilation louvres on the motor.
10. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
A Carbide reversible planer knife
Order no.: 6.30282 (2 pieces)
Order no.: 6.30272 (10 pieces)
B Chargers: ASC ultra, ASC 30-36, ASC 15, etc.
C Battery packs with different capacities. Only buy
battery packs only with voltage suitable for your
power tool:
4.0 Ah (6.25591), 5.2 Ah (6.25592), 5.5 Ah
(6.25342), 6.2 Ah (6.25341), 7.0 Ah (6.25345),
etc.
For a complete range of accessories, see
www.metabo.com or the catalogue.
11. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
The drive belt cable must only be replaced by
Metabo or an authorised customer service
workshop.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.

12. Environmental Protection

Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: never dispose of
power tools in your household waste! Used
power tools must be collected separately and
handed in for environmentally compatible recycling
in accordance with European Directive 2012/19/EU
on waste electrical and electronic equipment and its
implementation in national legal systems.
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Discharge the battery pack in the power tool before
disposal. Prevent the contacts from short-circuiting
(e.g. by protecting them with adhesive tape).

13. Technical Data

Explanatory notes on the specifications on page 3.
Subject to change in accordance with technical
progress.
U = Voltage of battery pack
P = Rated input power
1
P = Power output
2
b = Planing width
t = adjustable planing depth
f = Largest rabbetting depth
max
l = Length of the planer's sole
n = Idle speed
0
m = Weight with smallest battery pack
Measured values determined in conformity with
EN 62841.
Permitted ambient temperature during operation:
-20 °C to 50 °C (limited performance with
temperatures below 0 °C). Permitted ambient
temperature for storage: 0 °C to 30 °C
Machine in protection class II
Direct current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on the operating conditions, the
condition of the power tool or the accessories.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Vibration total value (vector sum of three directions)
determined in accordance with EN 62841:
a = vibration emission value
h
(Planing soft wood)
K = Uncertainty (vibration)
h
Typical A-weighted sound levels:
L = Sound-pressure level
pa
L = Acoustic power level
WA
K , K = Uncertainty
pA WA
The noise level can exceed 80 dB(A) during
operation.
Wear ear protectors!
ENGLISH en
13