Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for EnGenius EnStation 6
Summary of Contents for EnGenius EnStation 6
- Page 1 Quick Installation Guide ENH500-AX | EnStation 6 Quick Installation Guide Outdoor Access Point / Client Bridge ENH500-AX | EnStation 6 ENH500-AX Device*2 PoE Adapter*2 Quick Installation Guide Power Cord*2 Adhesive Label Waterproof*2 Screw Set*2 Pole Mounting Strap*2 Outdoor Access Point...
-
Page 2: Minimum Requirements
EnStation 6 Device *2 PoE Adapter*2 Quick Installation Guide Sealing nut*2 Bracket*2 Power Cord*2 Dynamic Stick*2 Screw Set*2 Pole Mounting Strap*2 Minimum Requirements Broadband Internet Service (Cable or DSL Modem) Internet Browser (Internet Explorer, Safari, Firefox, Chrome, Edge) Outdoor Access Point... -
Page 3: Connecting The Device
1 - Connecting the Device ENH500-AX a. Remove the rear bottom panel. b. Connect one end of the Ethernet Cable to the LAN(PoE) port of the AP/Bridge and the other end to the PoE Port on the PoE Adapter. c. Connect the Power Cord with the PoE Adapter and plug the other end into an electrical outlet. - Page 4 • The device should ONLY be powered via Ethernet Cable connected to the included PoE Adapter, EnStation 6 supports Proprietary 24V/54V PoE input. • The 2nd Ethernet Port of the device can supply the 802.3af power source when used with the included PoE Adapter.
-
Page 5: Ip Address Configuration
2 - IP Address Configuration a. Once your computer is on, ensure that your TCP/IP is set to “ON” or “Enabled”. Open Network Connections and then click Local Area Connection. Select Internet Protocol Version 4 (TCP/IPv4). b. If your computer is already on a network, ensure that you have set it to a Static IP Address on the interface. -
Page 6: Device Setup
3 - Device Setup a. To configure the device, open a web browser. In the web browser’s address bar enter 192.168.1.1 and hit enter. b. A long screen will appear. By default, the device username is “admin,” and the password is “admin”. -
Page 7: Switching Modes
4 - Switching Modes Configure on GUI a. The device can operate in the following modes: • Access Point, Client Bridge, WDS AP or WDS Station. • Note: The model name on the login screen depends on the product you are using. Outdoor Access Point... - Page 8 a. Click on the Wireless link under the Network and set up the Operation Mode. • It may take up to 90 seconds for the device to initially power up. Configure on EnWiFi App b. Use EnWiFi App, open “Configure Wireless” to set up the Operation Mode. Outdoor Access Point...
-
Page 9: Mounting The Device
5 - Mounting the Device Wall Mounting a. Determine where the Access Point is to be placed and stick the Adhesive label on the surface. b. Use the appropriate drill bit to drill the 8.1 mm diagram and 26 mm depth holes on the markings of the label. - Page 10 a. Plug the dynamic stick into the bracket. b. Screw the sealing nut and assembled parts, tighten it with 80kgf.cm. c. Put the nock washer on the dynamic stick. d. Assemble the mounting parts to the device. e. Determine the mounting location. Mark and drill two pilot holes aligning to the screw holes of the bracket. f.
-
Page 11: Pole Mounting
Thread the open end of the pole strap through the two tabs on the bracket. f. Lock and tighten the pole strap to secure the bracket to the pole. EnGenius Technologies | 1580 Scenic Ave. Costa Mesa, CA 92626 Maximum data rates are based on IEEE 802.11 standards. Actual throughput and range may vary depending on distance between devices or traffic and bandwidth load in the network.