Related Manuals for Echo CLS-5800
Summary of Contents for Echo CLS-5800
- Page 1 OPERATOR’S MANUAL CLEARING SAW CLS-5800 CAUTION Read Rules for Safe Operation and Instruction Carefully ECHO POWER EQUIPMENT (CANADA) 501 Newbold Street, London, Ontario Canada N6E 1K4 X750-005 88 3 X750 226-440 3 Printed in Japan 0506n 0605 ES...
- Page 2 Make sure the decal is legible and that you understand and follow the instructions on them. If a decal cannot be read, a new one can be ordered from your ECHO dealer. Safety decal: Part number 890317-49030...
- Page 3 LISTED IN THE OPERATOR’S MANUAL AND SUPPLIED WITH THE BLADES. 1. Do not operate unless the debris shield and safety harness are in good condition 1. THE ECHO SAW TOOTH BLADE IS and properly installed. DESIGNED TO CUT BRUSH AND SMALL TREES.
- Page 4 Clutch Automatic centrifugal clutch Fuel Mixing ratio Mixture of gasoline (Unleaded, 89 octane minimum) and specially blended 50 : 1 ECHO two cycle engine oil. Tank capacity 0.68 (23.0 US fl. oz.) Drive shaft Gear housing 60 degree bevel gears, ratio 1 : 1.4 (Counterclockwise)
- Page 5 ASSEMBLING DRIVE SHAFT • Stand engine upright on a level floor. • Fit drive shaft assembly ensuring that the drive shaft is correctly engaged. • Tighten four bolts (M5×25) to fasten drive shaft assembly. WARNING DANGER Bolts M5×25 NEVER START ENGINE WITHOUT SHAFT TUBE ASSEMBLY INSTALLED.
- Page 6 INSTALLATION OF CLEARING BLADE Adapter plate (A) • Place the blade on the adapter plate (A). • Place the adapter plate (B) atop the axle. Shield • The flat side of adapter plate (B) should be on the blade. • Put the cup washer on the adapter plate (B) and secure the lock nut counterclockwise.
- Page 7 Gasohol may contain maximum 10% ethyl (grain) alcohol or 15% MTBE (methyl tertiary-butyl ether). Gasohol containing methyl (wood) alcohol is not approved. OIL: ECHO brand premium two-stroke 50 : 1 oil is Fuel mix chart 50 : 1 (2%) requirred. METRIC Mix oil and gasoline /gasohol according to instructions on the oil container label.
- Page 8 STOPPING ENGINE Throttle trigger Ignition switch • Release throttle trigger and allow to run at an idle speed. • Slide ignition switch to “STOP” position. Stop OPERATING THE MACHINE CAUTION Do not allow either people or animals into the • Adjust handle to a convenient position for cutting work area.
- Page 9 THE IMPROPER USE OF STEEL BLADES. READ AND COMPLY WITH SAFETY INSTRUCTIONS LISTED IN THIS MANUAL. 2. ECHO WILL NOT BE RESPONSIBLE FOR THE FAILURE OF CUTTING DEVICES WHICH HAVE NOT BEEN TESTED AND APPROVED BY ECHO FOR USE WITH THIS UNIT.
- Page 10 MAINTENANCE AND CARE - ALWAYS KEEP THE UNIT CLEAN - AIR FILTER • Clean before using the unit. - Close choke and remove air cleaner cover. Air filter - Remove air filter (Air filter is located inside air Air cleaner cover cleaner cover).
- Page 11 SPARK PLUG • Check periodically. • Standard spark plug gap is 0.6 to 0.7 mm (0.024 to 0.028 in). • Replace if either electrode is worn or if the insulator is fouled by oil or other deposits. • TORQUE = 15 to 17 N •...
- Page 12 CHECK FUEL SYSTEM • Check before every use. • After refuelling make sure fuel does not leak or exude from around fuel pipe, fuel grommet or fuel tank cap. • In case of fuel leakage or exudation there is a danger of fire.
- Page 13 TROUBLE SHOOTING Poor performance of the engine and/or trimming mechanism can normally be prevented by carefully following instructions. Poor performances can easily be corrected even by a beginner. When the engine does not function properly check the following three (3) points first. •...
- Page 14 Table 2 Improper fuel used Use fuel with correct mixing ratio. Never use gasoline of poor quality. Spark plug defective (burnt) Replace. As cooling fins clogged, air Clean fins. Engine overheated does not pass well Excessive deposits in Disassemble and remove carbon. combustion chamber Plug damaged or fouled Replace or clean.