Advertisement
Available languages
Available languages
OBJ_BUCH-430-010.book Page 7 Wednesday, July 13, 2016 3:28 PM
Hammer Safety Warnings
Wear ear protectors. Exposure to noise can cause hear-
ing loss.
Use auxiliary handle(s), if supplied with the tool. Loss
of control can cause personal injury.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting ac-
cessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator an
electric shock.
Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Never use the machine with a damaged cable. Do not
touch the damaged cable and pull the mains plug when
the cable is damaged while working. Damaged cables in-
crease the risk of an electric shock.
Products sold in GB only: Your product is fitted with an
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for chiselling work in concrete, brick,
masonry and asphalt as well as for driving in and compacting,
when using the respective accessories.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
Bosch Power Tools
1 Dust protection cap
2 Locking sleeve
3 Chisel adjustment ring (Vario-Lock)
4 Vibration damper
5 Handle (insulated gripping surface)
6 On/Off switch
7 Thumbwheel for preselection of impact rate
8 Service indicator
9 Stand-by indicator
10 Auxiliary handle (insulated gripping surface)
11 Knurled nut for auxiliary handle
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Demolition Hammer
Article number
Rated power input
Impact rate
min
Impact energy per stroke
Chisel positions
Tool holder
Lubrication
Weight according to EPTA-
Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Assembly
Before any work on the machine itself, pull the mains
plug.
Auxiliary Handle (see figure A)
Operate your machine only with the auxiliary handle
10.
The auxiliary handle 10 can be set to any position for a secure
and low-fatigue working posture.
– Loosen the knurled nut 11, rotate the auxiliary handle 10
around the axis of the machine to the required position and
tighten the knurled nut 11 again.
– The auxiliary handle 10 can be mounted to a different posi-
tion. For this, completely unscrew the knurled nut 11 and
then pull out the hexagon bolt upward. Pull off the auxiliary
handle 10 to the side and turn around the remaining
clamping element by 180°. Mount the auxiliary handle 10
in reverse order.
Changing the Tool
With the SDS-max tool holder, simpler and easier tool chang-
ing is possible without additional aids.
English | 7
GSH 5 CE
Professional
3 611 C21 0..
W
1150
-1
1300– 2900
J
13
12
SDS-max
Central permanent lu-
brication
kg
6.2
/II
1 609 92A 1U9 | (13.7.16)
Advertisement
