Epson Stylus CX3100 Quick Start Manual

Setup
Unpacking Unpacking Unpacking Unpacking
The contents may vary in certain locations. Remove all tapes and protective materials following the Notice Sheet.
Setting Up the Stylus CX Setting Up the Stylus CX Setting Up the Stylus CX Setting Up the Stylus CX
1. Unlocking
2. Attaching the Parts
3. Plugging in the Power Cord
4. Installing the Ink Cartridges
1. Press the P On button to turn on this product.
On
Scan
Press the P On button.
2. Open the ink cartridge packages.
Setting Up the Computer Setting Up the Computer Setting Up the Computer Setting Up the Computer
1. Connecting
1. Turn off your Stylus CX.
Note:
Do not turn on this product until a
message prompts you to do so.
2. Connect the USB cable.
Note:
If the "Add New Hardware Wizard" dialog box appears, click Cancel and
disconnect the USB cable from this product.Then return to step 1. Connecting.
English
4033221-00
xxx
ink cartridges feeder guard
Set the paper support to
align with the arrows on
this product.
Stop
Return to Top
Error
Recall Reset Color
Copies
Save(3sec) Reset all(3sec) Enter
Value
B&W
Menu
Do not remove the blue portion of the tape seal
from the top of the cartridges.
Do not touch this part.
On
Error
Scan
Recall Reset
Save(3sec) Reset all(3sec)
Press to turn off.
c
Cautions
to avoid damage to your
equipment.
paper support
Be sure to use the USB cable
that comes with this product.
3. Insert the ink cartridges as illustrated below.
Note:
Install both ink cartridges. This product does not work unless both cartridges are
installed properly.
4. Close the scanner unit.
Ink charging starts. It takes about one and a half minutes. While charging, this
product produces a variety of mechanical sounds. This is normal. When the P
On light stops flashing, ink charging is complete.
c
Caution:
Do not turn the power off during the ink charging process.
Do not load paper until ink charging is complete.
Note:
The ink cartridges packaged with this product are partly used during the initial
setup to fully charge the print head. This one-time process consumes a
considerable amount of ink but subsequent cartridge sets will last for their full
rated life.
5. Selecting Language
You can select your preferred language for use on the LCD panel. For details, see
Chapter 1 in the Copy Guide.
This product is now ready to make copies. See "Using the Copy Feature" on the reverse
side. If you want to print data or scan images, set up your computer as described below.
2. Installing the Software
c
Caution for Macintosh users:
Turn off all virus protection programs before you install the software.
Co
For Mac OS X users, see "Installing the Software for Mac OS X" on the reverse side.
V
Menu
1. Make sure that this product is off.
2. Insert the software CD into the CD-ROM drive.
For users of Mac OS 8.6 to 9.x:
Double-click the EPSON icon in the EPSON folder.
3. The EPSON Installation Program dialog box appears.
Select Install Software, and then click
4. Follow the on-screen instructions.
5. For users of Mac OS 8.6 to 9.x
After installing the software, choose Chooser from the
Apple menu, and then select the icon for this product
and the port that this product is connected to.
Note for Windows users:
You may need to restart your computer while installing the software. If a message
instructing you to restart appears, remove the software CD, then click Restart. After
restarting make sure this product is off, then reinstall the software.
This product is now ready to print and scan. The Reference Guide includes detailed
information about printing and scanning. To view the Reference Guide, see "Viewing the
Reference Guide" on the reverse side.
Cautions and Notes
must be observed Notes contain important
information and useful tips on the
operation of this product.
USB cable
CD-ROM
Power cord may come
attached in some countries.
Flashing
On
Error
Scan
Recall Reset
Reset all(3sec)
Save(3sec)
.
power cord
On
On
Scan
Recall
Save(3sec)
For users of Mac OS 8.6 to 9.x
EPSON Installation Program
dialog box