Sanyo VCC-9700P Instruction Manual page 29

Pan and Tilt Settings (PAN/TILT)
A
Setting the motion sensor (MOTION)
The built-in motion sensor will work for preset positions, allowing the
camera to detect movements in the target object such as an intruder.
Use the joystick lever (xy) to select [MOTION], use the lever (vw)
to select "ON y", and press the [ENTER] button.
Available settings:
• OFF: Disables the motion sensor.
• ON: Enables the motion sensor.
(The MOTION SETTING screen appears.)
Before performing the settings under [MOTION], be sure
to set [MOTION] in the ALARM screen to "PRESET".
When [MOTION] is set to options other than "PRESET",
"---" displays for [MOTION] in the CAMERA VIEW screen
and settings cannot be made.
MOTION SETTING
SIZE
MASKING
SENSITIVITY
ZOOM
DURATION
PRESET
MENU
A Setting the size of the motion sensor (SIZE)
Set the detection pattern according to the size of the target object
to be detected for alarm. A movement in the target object will be
detected within the area where the detection pattern is specified.
1 Use the joystick lever (xy) to select [SIZE] – "SET y", and
press the [ENTER] button.
The MOTION SIZE screen appears displaying the detection
pattern (V1/H1) in the center of the screen.
MOTION SIZE
V 1
H 1
PRESET
MENU
2 Use the joystick lever to adjust the values for "V" and "H"
settings.
The size of the detection pattern will change depending on the
values set for "V" and "H".
• V: 1 - 6 (Sets the size for vertical direction.)
• H: 1 - 8 (Sets the size for horizontal direction.)
Memo: The maximum value for "V x H" is 9. When setting "V" or "H"
and the multiplied value exceeds the maximum value, the
other value will automatically be adjusted so that the value for
"V x H" does not exceed 9.
B Setting the mask patterns for the area to be excluded
in motion detection (MASKING)
If you have an area where you don't want to detect motion in the
target object (swaying trees, flickering of light, etc.), you can set
the mask pattern over the area so that the motion sensor does not
react to it.
A
SET y
OFF
SET y
B
OFF
C
5S
D
OFF
E
BACK
OFF
BACK
1 Use the joystick lever (xy) to select [MASKING], use the
lever (vw) to select "ON y", and press the [ENTER] button.
The MOTION MASKING screen appears. A mask pattern is
displayed in the top left of the screen.
MOTION MASKING
CONTINUE (y)
2 Use the joystick lever to move the mask pattern to the
area where you don't want to detect motion, and press the
[ENTER] button.
This sets one mask pattern for the area to be excluded in
detecting. If you want additional mask patterns to be set,
repeat the above procedure.
<To delete the mask pattern>
Use the joystick lever (xy or vw) to place a mask pattern over
the mask pattern to be cancelled, then press the [ENTER]
button.
3 Use the joystick lever (y) to move a mask pattern to the
bottom area of the screen and continue holding the lever
straight down for three seconds.
This completes the mask pattern setting procedure.
C Setting the detection sensitivity (SENSITIVITY)
You can set the level of sensitivity for motion detection. Adjusting
the level of sensitivity avoids unwanted detection.
1 Use the joystick lever (xy) to select [SENSITIVITY] – "SET
y", and press the [ENTER] button.
The SENSITIVITY screen appears.
SENSITIVITY
MOVE
Y-LEVEL
Y-DIFFER
DURATION
TEST
2 Set the detection level for the following parameters.
For all parameters, the larger the value, the lower the
sensitivity.
a Motion sensitivity (MOVE): 1 - 10
To avoid detection of small movements, make the value
larger.
b Brightness level (Y-LEVEL): 1 - 10
When noise from a dark screen is causing erroneous
detections, make the value larger.
c Brightness differences (Y-DIFFER): 1 - 10
To avoid detection of lights turning on and off, make the
value larger.
d Duration (DURATION): 1 - 60
To avoid detection of fast movements, make the value
larger.
3 To test the sensitivity settings, use the joystick lever (xy)
to select [TEST] and use the lever (vw) to select "ON".
When a motion is detected, patterns are shown in that
location. Adjust the setting values as necessary.
a
b
5
5
c
5
1
d
OFF
28