Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
INSTALLATION MANUAL
Color CCD Camera
Install these units securely according to this installation
manual. Be aware that allowing them to fall may cause
personal injury.
This installation should be made by a qualified service
person and should conform to all local codes.
Please read this manual before installing and using this unit, and always follow the instructions in it for proper
use. Please also read the separate Instruction Manual before using the unit for proper use.
1
Remove the plastic cover (A) and then
the tape (B) fixing the lens.
2
Put back the plastic cover (A) and lock it
securely.
● Turn the cover clockwise until it clicks.
Product Lineup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Surface Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
In-ceiling Mount (Closed Type) . . . . . . . . . . . . . . . . . . 3
In-ceiling Mount (Open Type) . . . . . . . . . . . . . . . . . . . . 4
Connections and Settings . . . . . . . . . . . . . . . . . . . . . . 5
Address Settings Table . . . . . . . . . . . . . . . . . . . . . . . . . 7
• Be careful when opening holes for installing the unit.
Work with the power and video cables pulled out for
easy installation.
• Make sure to properly perform waterproofing for the
ceiling where you are installing the unit.
• Make sure that the surface in the installation location
has no unevenness and is strong enough to bear the
total weight of the unit.
• Install this unit in an environment where the
temperature range stays between -10°C and +50°C
(no condensation allowed).
CAUTION: For VA-80S (Power Borard Unit)
ALL-POLE MAINS SWITCH with a contact separation of
at least 3mm in each pole shall be incorporated in the
electrical installation of the building.
Before Installing the Unit
Contents
Important
(A)
1
2
(B)
Advertisement
Related Manuals for Sanyo VCC-9500P
Summary of Contents for Sanyo VCC-9500P
-
Page 1: Table Of Contents
INSTALLATION MANUAL Color CCD Camera Install these units securely according to this installation manual. Be aware that allowing them to fall may cause personal injury. This installation should be made by a qualified service person and should conform to all local codes. Please read this manual before installing and using this unit, and always follow the instructions in it for proper use. -
Page 2: Product Lineup
Product Lineup To install the camera unit, the optional housing is required. When using a housing, be sure to choose the correct one for your environment of use. ☞ For instructions on how to install the outdoor type, the wall mounting bracket, pendant mounting bracket, and attachment, refer to the relevant instruction manuals. -
Page 3: Surface Mount
Surface Mount Make sure to also consult the Surface Cover Instruction Manual. 1. Installing the power board unit 1 Place the pattern sheet at the end of this manual on the ceiling, mark the locations and drill the holes for the cables and screws. -
Page 4: In-Ceiling Mount (Closed Type)
9 Align the arrows (C) of the same color (blue) on the camera unit and the inner side of the bracket, and push the camera unit until they click. F Align the SANYO logos on the supplied bracket cover and the bracket, and push the cover until they click. -
Page 5: In-Ceiling Mount (Open Type)
9 Align the blue sticker (F) on the bracket and the arrow (F) of the same color on the camera unit, and then push the camera unit until they click. F Align the SANYO logos on the supplied bracket cover and the bracket, and push the cover until they click. -
Page 6: Connections And Settings
Set either to RS485 or coaxial (COAX). Alarm input Coaxial (COAX) signal Protocol Set the protocol for controlling the camera. SSP (SANYO) Alarm output Termination (Switch 5) signal “OFF” is set by default. When connecting multiple cameras, termination setting must be “ON”... - Page 7 ■ To prevent electromagnetic interference Be sure to attach the clamping cores supplied with the camera unit to the cables as illustrated. ■ Connections for using coaxial control (System connection) Video input terminal Camera Digital video recorder (sold separately) Video input terminal Monitor (sold separately)
-
Page 8: Address Settings Table
Address Settings Table Addresses are specified by setting the switches to ON/OFF. In the table, the circle mark “m” means ON. Set switches as shown in the table. SANYO protocol: 1 - 127 • Switch 8 is unused. Address (Camera No.) Switch No. -
Page 9: Pattern Sheet (Inserted At The End Of This Manual)
Pattern Sheet: mm (inch) 4- φ4.5 (0.2) P. D φ168 (6.6) 166 (6.5) Scale: 1/1... - Page 10 Dimensions: mm (inch) φ 136 (5.4) Printed on recycled paper Imprimé sur du papier recyclé Impreso en papel reciclado Gedruckt auf Recyclingpapier 使用再生纸印刷 1AC6P1P3149-- L5BU2/XE (1206KP-SY) SANYO Electric Co., Ltd. Printed in Japan...