Panasonic Palmcorder VHSC PalmSight PV-L759 Service Manual page 29

PC Connection (continued)
Plug-in Driver for Adobe® PhotoDeluxe™ HE 3.0 (PV-L859 only)
The Plug-in Driver allows interface between Camcorder and PhotoDeluxe HE 3.0 application.
Note:
Install Adobe PhotoDeluxe HE 3.0 before proceeding.
1
Turn on PC (Personal Computer) and
start up Windows.
2
Insert Plug-in Driver disk into Drive A.
3
Select "Start" "Programs"
"Windows Explorer"
4
Copy "\Plug-in\Palmcorder.8ba"
file to "\PhotoDeluxe 3.0\Plug-
ins" folder.
5
When installed, start up PhotoDeluxe HE 3.0 and follow instructions on how to
transmit images.
Operation Notes
Attaching Optional Filters and Lenses
When you remove the Lens Hood, pinch the Lens Hood
and turn it counterclockwise as illustrated at right.
Then attach an optional filter or lens.
• Be careful not to touch the lens itself.
• Replace the Lens Hood after removing the accessory.
Lens Hood Area Operation Caution
With a Wide or Telephoto conversion lens (optional) attached, the four corners of the
screen may darken when zoom is set to maximum wide angle.
When attaching the lens hood, a Wide or Telephoto conversion lens (optional), etc. after
a filter (optional) has been attached, the four corners of the screen may darken when
zoom is set to maximum wide angle.
With two filters (optional) attached, the four corners of the screen may darken when zoom
is set to maximum wide angle.
External MIC IN
Connect an external Microphone (optional) using an M3 connector if necessary.
The built-in microphone is automatically
disconnected when an external microphone is plugged in.
EXT MIC
External Microphone
(not supplied)
Using a PCMCIA Adaptor (optional)
A
B
1-11
If your PC has a PCMCIA type II slot, you can insert the CompactFlash Card into a
PCMCIA adaptor (optional) to transfer images, captured with this Camcorder only, to
your PC.
Inserting a CompactFlash Card
1
2 5
,
3 4
,
Cleaning EVF (Electronic Viewfinder)
PV-L759/PV-L779
To Remove
PV-L859
To Remove
(Side view)
(Top view)
Before you begin...
• Turn your PC on.
• Set Camcorder POWER to OFF.
1
Remove the CompactFlash Card
from the Camcorder.
2
Hold the CompactFlash Card so that
the arrow side faces up and points
toward the PCMCIA Adaptor.
Securely insert the card into the
PCMCIA Adaptor slot as far as it will
go.
3
Hold the PCMCIA Adaptor so that
the arrow side points toward the
PCMCIA type II slot of your PC
(Personal Computer). Securely
insert the PCMCIA Adaptor as far as
it will go.
• Depending on the PC, it may
be necessary to turn the PCMCIA
Adaptor upside down in order to
insert the card.
4
To remove, push the eject button on
your PC (may vary by machine) and
pull the PCMCIA Adaptor out until it
is no longer inserted in the PC
(Personal Computer).
5
Pull the CompactFlash Card out of
the PCMCIA Adaptor.
Note:
• Do not remove the PCMCIA Adaptor from the
PC while the PC is working or while image
data is being transferred between the
CompactFlash Card and the PC (including
operation such as opening and storing
images), this will cause irreversible damage to
the memory.
• If you change file name or folder in the CF
card, the images be displayed properly on
PHOTO mode.
1
Turn the EVF Eyepiece
counterclockwise 1/8 of a turn.
2
Pull free.
Remove any lint or dust particles
with a soft clean cloth being careful
not to scratch the glass surfaces.
3
To re-install EVF
Line up the marks on the Eyepiece
with the grooves inside the EVF
shaft and attach. Turn the EVF
clockwise 1/8 of a turn to lock in
place.
1
Slide and hold Eyepiece RELEASE
button.
2
Slide the Eyepiece as shown.
(DO NOT TWIST.)
3
Remove lint or dust with a lens
blower (available where photography
accessories are sold). DO NOT
touch lens with fingers. Then,
replace Eyepiece.