Panasonic Palmcorder VHSC PalmSight PV-L759 Service Manual page 24

Playing Back Recordings (continued)
TV Playback or Viewing
Connect Camcorder to a TV to view
playback or recordings in progress.
TV with AUDIO/VIDEO IN Jacks.
TV
To Audio In To Video In
Audio/Video
Cable
(Supplied)
To Audio/Video Out
TV without AUDIO/VIDEO IN Jacks.
To Audio/
Video Out
RF Adaptor
optional
VHF Antenna
300 ohm-75 ohm
CH 3/4 Switch
transformer
or F Connector
UHF Antenna
VCR/TV
Selector
Back of TV
VHF Connecting
Cable
To VHF Antenna
VHF
Terminal
UHF
Digital Zoom
Power Zoom magnification is digitally increased.
3
T W
1 2 4
,
50 50×
D.ZOOM1 .ZOOM1
Before you begin...
• Connect Camcorder to power source.
• Make all TV-Camcorder connections.
1
Set POWER to:
VCR view playback.
CAMERA view picture as it is
recorded.
2
Turn TV ON and set to LINE
INPUT.
See TV owner's manual.
3
Begin playback or recording.
If TV has no VIDEO/AUDIO IN jacks,
connect PV-RF16 RF Adaptor
(optional). Tune TV to CH 3 or 4 to
match RF Adaptor 3/4 switch. Set
Adaptor's TV/VCR switch to VCR for
playback.
To watch TV only,
turn TV on without AUDIO/VIDEO IN Jacks
connected (left).
a Set Camcorder POWER to OFF.
b
Set RF Adaptor VCR/TV Selector to TV.
c
Turn TV ON and select channel.
CATV System Installer
This reminder is provided to call the
CATV system installer's attention to
Article 820-40 of the NEC in USA (and
to the Canadian Electrical Code in
Canada) that provides guidelines for
proper grounding and, in particular,
specifies that the cable ground shall be
connected to the grounding system of
the building, as close to the point of
cable entry as practical.
Before you begin...
• Connect Camcorder to power source.
• Set POWER to CAMERA.
1
Slide DIGITAL SELECT to D.ZOOM.
2
Press D. ZOOM.
once D.ZOOM 1 (150× maximum)
twice D.ZOOM 2 (300× maximum)
Higher digital magnification levels
may cause picture distortion.
3
Hold down "T" on POWER ZOOM.
Digital Zoom starts when normal
zoom reaches maximum (26×).
• Zoom level appears in EVF.
• POWER ZOOM switch controls
digital zoom level.
• Normal zoom resumes when level
falls to 26×.
4
Press D. ZOOM to turn off Digital
Zoom so no indication
appears.
Note:
• If "NOW IN DIGITAL WIPE" is
displayed when D. ZOOM is pressed,
DIGITAL SELECT is currently in
DIGITAL WIPE mode and the DIGITAL
ZOOM feature is not available.
Color Digital Filter
Digital Filter adds one of 5 colors to entire
picture, like a color filter.
2 3 4 5
, , ,
DISPLAY DISPLAY MENU MENU
1
6
PHO PHOTO
VCR VCR CAMERA CAMERA
OFF OFF
SEPIA
D.FILTER
YEL
RED
RED
BLU
GRN
Digital E.I.S.
Digital Electronic Image
Stabilization (E.I.S.)
Helps stabilize picture when recording in
unstable situations.
1 2 3
,
NORMAL
EIS
Digital EIS ON
1-6
Before you begin...
• Connect Camcorder to power source.
• Set POWER to CAMERA.
1
UP UP
Slide DIGITAL SELECT to FADE.
DOWN DOWN
2
Press MENU for MENU mode.
Press UP or
TIME LAPSE ; TIME LAPSE ; OFF
DOWN to select
MESSA MESSAGE GE ; ; OFF
SECURITY SECURITY ; ; OFF
VIDEO EFFECTS .
VIDEO EFFECTS VIDEO EFFECTS
SELECT : PUSH SELECT : PUSH
SET SET : : PUSH DISPLA PUSH DISPLAY KEY
END END : : PUSH MENU KEY PUSH MENU KEY
3
Press DISPLAY for VIDEO
EFFECTS menu.
- - - VIDEO EFFECTS - - - - - - VIDEO EFFECTS - - -
Press DOWN
AUT UTO F O FADE ADE
DIGIT DIGITAL F AL FADE
to select
DIGITAL FIL DIGIT AL FILTER
DIGITAL FILTER .
SELECT : SELECT : PUSH PUSH
SET : PUSH DISPLA PUSH DISPLAY KEY
END : PUSH MENU KEY PUSH MENU KEY
4
Press DISPLAY for DIGITAL FILTER
menu. Press UP or DOWN
select from 5 colors.
- - DIGIT - - DIGITAL FIL AL FILTER ; TER ; COLOR - -
SEPIA
YELLOW
RED
SELECT : SELECT : PUSH PUSH
SET SET : : PUSH DISPLA PUSH DISPLAY KEY
5
Press DISPLAY to confirm entry.
Press MENU to exit.
6
Start recording.
• To cancel Digital Filter, set POWER to
OFF.
Note:
• Color Digital Filter will not function
during Digital Wipe mode, Picture in
Picture Wipe Title or Still/Strobe/Wide.
• Picture returns to normal in Still mode.
Before you begin...
• Connect Camcorder to power source.
• Set POWER to CAMERA.
1
Slide DIGITAL SELECT to EIS.
2
Press EIS to display "EIS" in the
EVF.
• The shutter speed auto-adjusts from
1/80 to 1/350 according to
brightness.
• Use High Speed Shutter
if needed. Shutter speed setting
remains after EIS is canceled.
3
Press EIS again to cancel when not
in use.
E.I.S. may not function during...
• extreme Camcorder movement.
• recording of subject with distinct
horizontal or vertical stripes.
• low light situations (EIS indicator
flashes).
• intense fluorescent lighting situations.
• recording of very fast motion.
Note:
• If "NOW IN DIGITAL WIPE" is
displayed when EIS is pressed,
DIGITAL SELECT is currently in
DIGITAL WIPE mode and the Digital
E.I.S. feature is not available.
PAGE 2/2 GE 2/2
OFF
OFF
OFF
; ; F FADE ADE
BLA BLACK CK
/ KEY KEY
Y KEY
ADE
TER
/ KEY
Y KEY
to
COLOR - -
BLUE
GREEN
/ KEY
Y KEY