Usb multifunction rio with kintex-7 160t fpga (17 pages)
Summary of Contents for National Instruments USB-9265
Page 1
This user guide describes how to use the National Instruments USB-9265 and lists the device specifications. Introduction The NI USB-9265 consists of two components: an NI 9265 module and an NI USB-9162 carrier, as shown in Figure 1. NI 9265...
(0.998 in.) Figure 2. NI USB-9265 Device Dimensions in Millimeters (Inches) Safety Guidelines Operate the NI USB-9265 only as described in this user guide. Hot Surface This icon denotes that the component may be hot. Touching this component may result in bodily injury.
Page 4
LV_Getting_Started.pdf LabVIEW Help—provides Help»Search the LabVIEW information about LabVIEW Help programming concepts, step-by-step instructions for using LabVIEW, and reference information about LabVIEW VIs, functions, palettes, menus, and tools. NI USB-9265 User Guide and Specifications ni.com...
If you need more help getting started developing an application with NI products, NI offers training courses. To enroll in a course or obtain a detailed course outline, refer to ni.com/training Technical Support on the Web For additional support, refer to ni.com/support zone.ni.com NI USB-9265 User Guide and Specifications ni.com...
Installing the Software Software support for the NI USB-9265 for Windows Vista/XP is provided by NI-DAQmx. The DAQ Getting Started Guide, which you can download , offers NI-DAQmx users step-by-step instructions ni.com/manuals for installing software and hardware, configuring channels and tasks, and getting started developing an application.
Page 8
Remove the protective cover from the 15-pin D-SUB connector. Align the I/O module with the carrier, as shown in Figure 5. Figure 5. Module Installation Squeeze the latches and insert the NI 9265 module into the NI USB-9162 carrier. NI USB-9265 User Guide and Specifications ni.com...
Figure 6. Locking Module into Place Connecting the NI USB-9265 to a Computer Plug one end of the USB cable into the NI USB-9265 and the other end into an available USB port on the computer. Refer to the NI-DAQmx for USB Devices Getting Started Guide that shipped with your device, and is also accessible from Start»All Programs»National Instruments»NI-DAQ,...
Page 10
A high voltage screw terminal backshell must be installed when using hazardous voltages (>42.4 V , 60 VDC). You must use 2-wire ferrules to create a secure connection when connecting more than one wire to a single terminal on the NI USB-9265. COM0 COM1 COM2...
Page 11
You can connect a load to each channel of the NI USB-9265. Connect the positive lead of the load to the AO terminal. Connect the ground of the load to the corresponding COM terminal. Refer to Figure 8 for an illustration of how to connect a load to the NI USB-9265.
Wiring for High-Vibration Applications If an application is subject to high vibration, National Instruments recommends that you either use ferrules to terminate wires to the detachable screw-terminal connector or use the NI 9932 backshell kit to protect the connections. Refer to Figure 9 for an illustration of using ferrules.
This category refers The maximum voltage that can be applied between any channel or V terminal and a COM terminal without damaging the module or other devices. NI USB-9265 User Guide and Specifications ni.com...
115 V for U.S. or 230 V for Europe. Caution Do not connect the NI USB-9265 to signals or use for measurements within Measurement Categories III or IV. Safety Standards...
Certification column. Environmental Management National Instruments is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial not only to the environment but also to NI customers.
Waste Electrical and Electronic Equipment (WEEE) At the end of their life cycle, all products must be sent to a WEEE recycling EU Customers center. For more information about WEEE recycling centers and National Instruments WEEE initiatives, visit ni.com/environment/weee.htm RoHS...
Page 18
Thailand 662 278 6777, Turkey 90 212 279 3031, United Kingdom 44 (0) 1635 523545 National Instruments, NI, ni.com, and LabVIEW are trademarks of National Instruments Corporation. Refer to the Terms of Use section on ni.com/legal for more information about National Instruments trademarks.