Table of Contents
Advertisement
Available languages
Available languages
English
Additional Safety Information
WARNING: Never modify the power tool or any part of
it. Damage or personal injury could result.
WARNING: ALWAYS use safety glasses. Everyday
eyeglasses are NOT safety glasses. Also use face or
dust mask if cutting operation is dusty. ALWAYS WEAR
CERTIFIED SAFETY EQUIPMENT:
•
ANSI Z87.1 eye protection (CAN/CSA Z94.3),
•
ANSI S12.6 (S3.19) hearing protection,
•
NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction activities
contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
•
lead from lead‑based paints,
•
crystalline silica from bricks and cement and other
masonry products, and
•
arsenic and chromium from
chemically‑treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.
Wear protective clothing and wash exposed areas
•
with soap and water. Allowing dust to get into your
mouth, eyes, or lay on the skin may promote absorption of
harmful chemicals. Direct particles away from face and body.
Use the appropriate dust extractor vacuum to remove
•
the vast majority of static and airborne dust. Failure
to remove static and airborne dust could contaminate the
working environment or pose an increased health risk to
the operator and those in close proximity.
Use clamps or other practical ways to secure and
•
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and may
lead to loss of control and injury.
Air vents often cover moving parts and should be
•
avoided. Loose clothes, jewelry or long hair can be caught
in moving parts.
CAUTION: When not in use, place tool on its
side on a stable surface where it will not cause
a tripping or falling hazard. Some tools with large
battery packs will stand upright on the battery pack
but may be easily knocked over.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
BPM .................... beats per minute
V ......................... volts
min ..................... minutes
j
or DC ............ direct current
.../min .............. per minute
RPM .................... revolutions per
minute
A ......................... amperes
6
Hz ....................... hertz
W ........................ watts
Wh ...................... watt hours
n o ....................... no load speed
n ......................... rated speed
c
..................... safety alert symbol
h
..................... wear respiratory
protection
f
..................... wear eye protection
i
..................... Class II Construction
(double insulated)
g
..................... wear hearing
protection
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove air supplyremove
the battery pack before making any adjustments
or removing/installing attachments or
accessories. An accidental start‑upactuation can
cause injury.
TOOL SPECIFICATIONS
Height
Width
Length
Weight (lbs/kg)
Recommended Operating Pressure
Air Consumption per 100 cycles
Loading capacity
Lubrication
FASTENER SPECIFICATIONS
Model
Nail
23 gauge wire (headless or slight head pins)
Lengths
5/8" (16 mm) –1‑3/8" (35 mm)
Air Inlet
nOTE: Use only PORTER‑CABLE approved fasteners
Trigger (Fig. A)
WARNING: Disconnect air line from tool and remove
fasteners from magazine before making adjustments
or personal injury may result.
WARNING: Keep fingers AWAY from trigger when not
driving fasteners to avoid accidental firing. Never carry
tool with finger on trigger.
The tool is shipped from the factory with a dual trigger
actuation system.
Air Fitting (Fig. B, C)
The tool is equipped with a 1/4" (6.4 mm) male quick
connector coupling. A 3/8" (9.5 mm) male quick connector
coupling is available from PORTER‑CABLE and may be used
when a 1/4" (6.4 mm) supply line is not available.
nOTE: A 3/8" (9.5 mm) supply line (and fittings) are required
for maximum tool performance. iMPORTAnT: Always use
couplings that relieve all pressure from the tool when it
is disconnected from the power supply. Always use hose
connectors that shut off air supply from compressor when
the tool is disconnected.
a
..................... read all
documentation
n
..................... avoid staring at
light
l
or AC............ alternating current
Ah ....................... amp hours
Pin138
7.5" (.19 mm)
1.9" (.05 mm)
8.1" (.21 mm)
2.1 lbs (0.95 kg)
60‑100 psi (4.1 to 6.9 bar)
1.61 SCF
132 nails
Oil‑Free
Pin138
1/4" NPT (6.4 mm)
Advertisement
Table of Contents
