Advertisement
Quick Links
Contents
These installation instructions describe how to install
your 45HG, 45HBV, 45HN and 45HZ Electronic
Stand-Alone Mortise Lock. Topics covered include:
Preparing the door ........................................................................ 1
Configuring and installing the mortise case........................... 3
Installing the trim ........................................................................... 4
Completing the installation......................................................... 9
For instructions to install 45HW & 47HW electrified
functions, see the Installation Instructions for 45HW &
47HW Electrified Mortise Locks (T81612).
1
Identify holes to drill
1 Determine the lock function to be installed.
2 Determine the inside and outside, hand, and bevel of
the door.
3 See the Holes by Function table and Figure 1 to
determine the holes to be drilled for the lock
function.
Holes by Function
Holes to drill
A M & N forged trim
a
(2 holes)
†
B Harness
C Standard cylinder
D Sensor & motor
wire
F Thumb turn
G Trim mounting
b
(2 holes)
††
H Lever
a. Determine trim holes based on trim type.
b. Because these holes pass through the mortise pocket, it is rec-
ommended that each hole be drilled separately rather than
straight through.
Installation Instructions for
Electronic Stand-Alone Mortise Locks
Functions
DV
LV
I/S O/S I/S O/S I/S O/S I/S O/S
Through
Through
Through
door
door
Through
Through
door
door
■
■
■
■
■
Through
Through
Through
door
door
Through
Through
Through
door
door
BEST ACCESS SYSTEMS
a Product Group of Stanley Security Solutions, Inc.
For hole sizes, see the
G11 Template (T81622).
Figure 1
NV
TV
Through
door
door
Through
door
■
■
■
Through
door
door
Through
door
door
A
B
C
F
H
G
A
Identifying holes to drill
B
G
D
1
Advertisement
Related Manuals for Stanley BEST 45HG
Summary of Contents for Stanley BEST 45HG
- Page 1 Determine trim holes based on trim type. b. Because these holes pass through the mortise pocket, it is rec- ommended that each hole be drilled separately rather than straight through. BEST ACCESS SYSTEMS a Product Group of Stanley Security Solutions, Inc.
-
Page 2: Preparing The Door
Note 2: For holes through the door, it is best to drill half- way from each side of the door to prevent the door from splintering. BEST ACCESS SYSTEMS a Product Group of Stanley Security Solutions, Inc. -
Page 3: Configuring And Installing The Mortise Case
2 To change the position of a hub toggle, remove the toggle screw, move the toggle into the desired position, and re-tighten the screw. BEST ACCESS SYSTEMS a Product Group of Stanley Security Solutions, Inc. -
Page 4: Installing The Trim
Caution: Do not overtighten the trim mounting plate plate screws. Overtightening may damage the locking mechanism. Inside mounting plate Figure 7 Installing the trim mounting plates BEST ACCESS SYSTEMS a Product Group of Stanley Security Solutions, Inc. - Page 5 1 On the outside of the door, insert the trim hole insert into the upper trim hole, as shown in Figure 10. 2 Insert the bushing into the harness hole. Figure 10 Installing the trim hole insert and bushing BEST ACCESS SYSTEMS a Product Group of Stanley Security Solutions, Inc.
- Page 6 4 Tighten the mounting screws until the fire plate is securely mounted to the door. Inside of door Figure 12 Installing the fire plate and bushing BEST ACCESS SYSTEMS a Product Group of Stanley Security Solutions, Inc.
- Page 7 2 Optional for Keypad EZ Locks only: Make the remote unlock connections with wire nuts or crimp connectors. See the Installation Instructions for Keypad EZ Remote Unlock (T80922) for more information. BEST ACCESS SYSTEMS a Product Group of Stanley Security Solutions, Inc.
- Page 8 3 Secure the cylinder in the mortise case with the cylinder retainer screw. 4 Install the core. Cylinder retainer screw (inside mortise case) Outside of door Figure 15 Installing the Keypad EZ Lock cylinder BEST ACCESS SYSTEMS a Product Group of Stanley Security Solutions, Inc.
-
Page 9: Completing The Installation
Outside of door Inside of door Spindles Spindles align the core opening in the escutcheon. Figure 17 Installing the levers 5 Turn the levers to check that they operate smoothly. BEST ACCESS SYSTEMS a Product Group of Stanley Security Solutions, Inc. - Page 10 Figure 18. Note: Phillips Type 2 and T20 Torx options are available for the cover mounting screws. Inside of door Figure 18 Installing the top cover BEST ACCESS SYSTEMS a Product Group of Stanley Security Solutions, Inc.
- Page 11 (or the filled area of the strike box). Note: The recommended gap between the door and Strike jamb is 1/8″ Figure 20 Installing the strike box and strike plate BEST ACCESS SYSTEMS a Product Group of Stanley Security Solutions, Inc.
- Page 12 2 Turn the lever and open the door. 3 Check the handle to make sure that the lock unlocks and then relocks. © 2006–2009 Stanley Security Solutions, Inc. and Stanley Logistics, Inc. T81627/Rev B 1929289 ER-7991-12 Oct 2009 BEST ACCESS SYSTEMS...