Advertisement
INTERVAL
CYCLE, OPTION, AND STATUS LEDs
CYCLE 1
CYCLE 2
CYCLE 3
HI TEMP
START/RESUME
CLEAN
ALL OTHER CYCLE, OPTION AND STATUS LEDs
INTERVAL TIME (min:sec)
SOIL SENSING INTERVALS AND SENSOR CHECKS
THERMISTOR (TEMPERATURE SENSOR) CHECK INTERVAL. TURN CLEAN LED ON
IF TERMISTOR IS IN NORMAL TEMPERATURE RANGE: 32˚F (167˚C).
LOADS
PILOT RELAY
FILL
WASH MOTOR
DISPENSER (DETERGENT/RINSE AID)
DRAIN MOTOR
HEATER
SERVICE DIAGNOSTICS NOTES
Service Diagnostics Cycle Notes:
1
To invoke the Diagnostics Cycle, perform the following while in standby:
■
Press any 3 keys in the sequence 1-2-3-1-2-3-1-2-3
with no more than 1 second between keys.
■
The Service Diagnostics Cycle will start when the door is closed.
■
To rapid advance 1 interval at a time, press the Start/Resume key.
Rapid advance may skip sensor checks as some checks require
2 complete intervals.
NOTE: While in the Diagnostic Cycle, the Start/Resume feature
is turned off (for example, Auto Resume after door interrupts)
and the Start/Resume key becomes an individual advance key.
■
Invoking Service Diagnostics clears all status and last ran
information from memory and restores defaults.
■
Drain and wash motors will pulsate on and off.
■
Last ran cycles and options returned to default.
■
Last ran delay returns to the lowest delay increment.
■
Operating state returns to Standby upon completing
or terminating the Service Diagnostics Cycle.
To quickly advance through customer cycles, invoke the Rapid Advance
mode by pressing HIGH TEMP - HEATED DRY - HIGH TEMP - HEATED DRY,
after starting the cycle. Then, press START/RESUME to advance through
cycle intervals.
Service Diagnostics Cycle
18 17 16
CY1
CY2
CY3
HIT
STA
NOTES 3, 5
CLN
ALL
TOTAL TIME: 20:52
NOTE
3
2
Customer Cycle Operation
15 14
13 12 11 10 9 8 7 6
CY1
CY1
CY1
CY2
CY2
CY2 CY2
CY3
CY3
CY3
HIT
HIT
HIT HIT
STA
STA
STA
STA
STA
STA STA
CLN
CLN
CLN
CLN
THR
PLT
PLT
FIL
FIL
WSH
1
1
1
1
4
2
Turn on all LEDs immediately upon receiving entry sequence (even
if door is open) for 5 seconds as a display test. Turn off all LEDs
for 1 second prior to reporting customer error history.
3
Thermistor (temperature sensor if present) checks:
■
Turn Clean LED on if thermistor is in its normal temperature
range of 32°F to 167°F (0°C to 75°C).
4
Cycle 2 and Hi Temp LEDs flash in this interval. Press Cycle
Select key in this interval to clear customer error history.
5
Turn on Clean LED in this interval if dispenser current detected
in previous interval.
NOTE: Rapid Advance mode is automatically enabled in the Service Diagnostic
cycle but must be manually invoked in customer cycles.
3
5 4
3
CY1
CY1
CY1
CY2
CY2
CY2 CY2
CY2
CY3
CY3
CY3
HIT
HIT
HIT
HIT
HIT
STA STA STA STA STA STA STA STA
(CLN)
(CLN)
PLT PLT
PLT
PLT
PLT
PLT
PLT PLT
FIL
WSH
WSH
WSH
WSH
DSP
DRN
DRN
HTR
HTR
5
3
3
4
2
1
CY1
CY2
CY3
HIT
STA
STA
S
CLN
CLN
T
A
N
D
B
Y
1
1
Advertisement
