Table of Contents
Advertisement
Section 1: Assembly & Set-up
Section 1: Assembly & Set-up
Tractor Requirements
Tractor horsepower should be within the range noted
below. Tractors outside the horsepower range must not
be used. Tractor must be equipped with a front mounted
loader that meets the following requirements:
Maximum tractor horsepower
CB1060 . . . . . . . . . . . . . . . . . . . . . . . 40 hp (30 kW)
CB1072 . . . . . . . . . . . . . . . . . . 40-60 hp (30-45 kW)
Maximum loader lift capacity
CB1060 . . . . . . . . . . . . . . . . . . . . 1150 lbs (522 kg)
CB1072 . . . . . . . . . . . . . . . . . . . 2400 lbs (1089 kg)
Maximum hydraulic pressure . . .3,000 psi (20.7 mPa)
Loader hitch type . . . . . . . . . . Universal Quick Attach
Hydraulic outlets:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Duplex outlet
. . . . . . . . or Third Function Valve Kit (See page 14)
Tractor weight. . . . . . . . . . . . . . . See warnings below
!
WARNING
To prevent serious injury or death:
•
Consult your power machine Operator's Manual for
operating capacity, lifting capacity, and operating
specifications. Exceeding rated capacities and
specifications can result in loss of control, roll-over or other
serious hazard.
•
Use a power machine of adequate size for the load being
carried. An undersized machine can roll over when raising
the loader arms due to high center of gravity.
•
Lightweight power machines may need weight added to the
rear to maintain steering control and prevent forward and/
or side tipping. Consult your power machine Operator's
Manual to determine proper weight requirements and
maximum limitations.
IMPORTANT: The CB10 Series 4-in-1 Combination
Buckets are not recommended for Skid Steers.
Before You Start
Allow only persons to operate this implement who have fully
read and comprehended this manual, and who have been
properly trained in the safe operation of this implement.
Serious injury or death can result from the inability to read,
understand, and follow instructions provided in this manual.
Make sure the intended power machine conforms to the
requirements provided on this page. Also, read and
understand this Operator's Manual for your 4-in-1
Combination Bucket. An understanding of how it works
will aid in its assembly and set-up.
Go through the "Pre-Assembly Checklist" on this page
before assembling the 4-in-1 Combination Bucket. To
speed up your assembly task and make the job safer,
have all needed parts and equipment readily at hand.
2/13/23
Table of Contents
Torque Requirements
Refer to "Torque Values Chart" on page 25 to determine
correct torque values when tightening hardware.
Have a hoist, forklift, or loader with properly sized chains and
safety stands capable of lifting and supporting the equipment
on hand.
Have a minimum of two people available during assembly.
Make sure all major components and loose
parts are shipped with the machine.
Double check to make sure all parts, fasteners,
and pins are installed in the correct location.
Refer to the Parts Manual if unsure.
NOTE: All assembled hardware from the factory
has been installed in the correct location.
Remember location of a part or fastener if
removed. Keep parts separated.
Make sure working parts move freely, bolts are
tight and cotter pins are spread.
Make sure all grease fittings are in place and
lubricated.
Make sure all safety labels are correctly located
and legible. Replace if damaged.
Tractor Shutdown Procedure
The following are basic tractor shutdown procedures.
Follow these procedures and any additional shutdown
procedures provided in your tractor Operator's Manual
before leaving the operator's seat.
1.
Reduce engine speed and disengage power take-off
if engaged.
2. Park tractor and implement on level, solid ground.
3. Lower implement to ground or onto non-concrete
support blocks.
4. Put tractor in park or set park brake, turn off engine,
and remove switch key to prevent unauthorized
starting.
5. Relieve all hydraulic pressure to auxiliary hydraulic
lines.
6. Wait for all components to come to a complete stop
before leaving the operator's seat.
7.
Use steps, grab-handles and anti-slip surfaces when
stepping on and off the tractor.
CB1060 & CB1072 4-In-1 Combination Bucket 381-169M
Pre-Assembly Checklist
Check
Ref.
Assembly
& Set-up
Operator's
Manual
381-169M
Parts Manual
381-169P
Operator's
Manual
Page 21
Page 6
9
Advertisement
Table of Contents
