Dimplex DXLAT75w Installation And Operating Instructions

Dimplex Skirting Heaters
Models : DXLAT75w, DXLAT150w & DXLAT150Tiw
Dimensions
(millimetres)
Models Specification
DXLAT75w 0.75KW Switch /
Thermostat / Neon
DXLAT150w 1.5KW Switch /
Thermostat / Neon
DXLAT150Tiw 1.5KW 24Hr Timer /
Thermostat
IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Important Safety Advice
If the appliance is damaged, check immediately with the
supplier before installation and operation.
WARNING – THIS APPLIANCE MUST NOT BE USED IN A
BATHROOM.
WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE
SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING
POOL.
WARNING – THIS HEATER MUST NOT BE LOCATED
IMMEDIATELY BELOW A FIXED SOCKET OUTLET.
DO NOT USE THE HEATER UNTIL THE FEET ARE FITTED
CORRECTLY.
FOLLOW these instructions carefully.
NEVER cover or obstruct in any way the heat outlet slots at
the top of the heater or the air inlet slots in the base of the
heater.
The heater carries the Warning symbol, indicating that
it must not be covered.
Warning: In order to avoid overheating, do not cover the
heater
Caution: In order to avoid a hazard due to inadvertent
resetting of the thermal cutout, this appliance must not be
supplied through an external switching device, such as a
timer, or connected to a circuit that is regularly switched on
and off by the utility.
This appliance is not intended for use by children or other
persons without assistance or supervision if their physical,
sensory or mental capabilities prevent them from using it
safely. Children should be supervised to ensure that they do
not play with the appliance.
If young children, the aged or infirm are likely to be left in the
vicinity of the heater, we advise that adequate precautions
should be taken. We recommend that a guard be fitted to
ensure contact with the heater is avoided and objects cannot
be inserted into the product.
If the mains lead is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an ~ supply only and the voltage
marked on the heater must correspond to the supply voltage.
This heater is fitted with a rewireable plug incorporating a 13
amp fuse. In the event of replacing the fuse in the plug supplied,
a 13 amp fuse approved by ASTA to BS 1362 must be used. If any
other type of plug is used, a 15 amp fuse must be fitted in the
plug, the adaptor, or at the distribution board.
A B C
300mm
250 120 850
305 165 865
13 : 17
ON P1
OFF ADVANCE
AUTO MAN ON
200mm
305 165 865
Installation and Operating Instructions
C
IMPORTANT : If the plug is not suitable for your socket, the 13
amp plug should be removed. Before wiring the appropriate plug,
please note that the wires in this mains lead are coloured in
accordance with the following code :
GREEN AND YELLOW:
BLUE :
BROWN :
Connect the GREEN AND YELLOW wire to the terminal marked
'E' or by the earth symbol
YELLOW.
Connect the BROWN wire to the terminal marked 'L' or coloured
RED.
Connect the BLUE wire to the terminal marked 'N' or coloured
BLACK.
General
The heater may be used free standing on feet or wall mounted
on the brackets. The necessary feet and wall brackets are
provided. The heater should only be operated when in the upright
position as shown in Fig.1.
Fitting Feet
Positioning the heater
When using the product free standing always ensure that the
heater is stood on a firm, level base near
beneath, a suitable mains supply socket, ensuring at least
300mm clearance from any shelf above.
Ensure that curtains and furniture are not positioned close to the
chosen position, as this would create a potential fire hazard.
See also 'Important Safety Advice'.
NEVER USE THE HEATER FREE STANDING WITHOUT THE FEET
FITTED.
INDCLTS7RG
A
ON P1
OFF
AUTO
EARTH
NEUTRAL
LIVE
, or coloured GREEN or GREEN AND
to, but not directly
Issue 4
B
13 : 17
MAN ON ADVANCE
Fig. 1
Fig. 2