Related Manuals for Compatible Systems DS3-10/100
Summary of Contents for Compatible Systems DS3-10/100
- Page 1 DS3-10/100 RIOP Installation Guide Compatible Systems Corporation 4730 Walnut Street Suite 102 Boulder, Colorado 80301 303-444-9532 800-356-0283 http://www.compatible.com...
- Page 2 DS3-10/100 RIOP Installation Guide, Version 1.0 Copyright© 1999, Compatible Systems Corporation All rights reserved. VSR, VSR-2, MicroRouter and CompatiView are trademarks of Compatible Systems Corporation. Other trademarks are the property of their respective holders. FCC Notice: This product has been certified to comply with the limits for a Class A computing device, pursuant to Subpart J of Part 15 of FCC Rules.
-
Page 3: Table Of Contents
Introduction to the DS3-10/100 RIOP Chapter 1 - Network Installation Ethernet Connection Requirements DS3 Line Connection Requirements Connecting the DS3-10/100 to the Ethernet Connecting the DS3-10/100 to a DS3 Line Connecting a Management Console Powering Up the Router Chapter 2 - Quickstart Configuration THERNET... - Page 4 IP Protocol Required for IP Numbered Interface Required for IP Unnumbered Interface Suggested for IP IPX Protocol Required for IPX Suggested for IPX AppleTalk Protocol Required for AppleTalk Suggested for AppleTalk DECnet Protocol Required for DECnet SMDS Configuration Link Configuration Suggested for Dedicated/Leased Line Operation SMDS Addressing AVING A...
-
Page 5: Introduction To The Ds3-10/100 Riop
DS3 interface has a data capacity of 44.736 Mbps, while the Ethernet interface can operate at either 10 Mbps or 100 Mbps. This section of the manual contains information specific to the DS3-10/100 RIOP. It is divided into the following sections:... -
Page 6: Chapter 1 - Network Installation
Chapter 1 - Network Installation This section of the manual will help you install the DS3-10/100 RIOP to connect a local Ethernet and remote corporate network. These connections can be made to other Compatible Systems routers or routers from other vendors. -
Page 7: Connecting The Ds3-10/100 To The Ethernet
Connecting a Management Console If you wish to connect an out-of-band management console, use the supplied cable and connect to the Console interface on the DS3-10/100 RIOP. You can use a dumb terminal or a computer equipped with VT100 terminal emulation. -
Page 8: Chapter 2 - Quickstart Configuration
This chapter briefly discusses the major parameters that must be set in order to use the DS3-10/100 RIOP as part of your VSR multigigabit switching router. Detailed information on the meaning of the router’s parameters is provided in the Compa- tiView Management Software Reference Guide and the Text-Based Configuration and Command Line Management Reference Guide. -
Page 9: Ethernet Interface Configuration
Ethernet Interface Configuration Ethernet interfaces are considerably easier to set up than WAN interfaces since there are fewer choices that need to be made regarding communications protocols and parameters. We recom- mend that you begin by configuring any Ethernet interface parameters before proceeding to configure WAN interface parameters. -
Page 10: Suggested For Appletalk
Suggested for AppleTalk You may want to set your own network numbers, rather than using the autoconfigured values. You may also want to use more meaningful zone names. CV: Use the AppleTalk Routing: Ethernet Dialog Box. TB: Use configure and set keywords in the AppleTalk Phase 2 Ethernet 0 section. DECnet Protocol Required for DECnet The router’s shipping configuration does not have DECnet turned on. -
Page 11: Ppp Configuration
Note: Due to the complexity of BGP, configuration parameters for BGP are not given in this Quickstart. For help with BGP configuration parameters, and other configuration questions, refer to the Tech Support pages on the Compatible Systems Web site at: http://www.compatible.com/. -
Page 12: Decnet Protocol
Dedicated line operation generally does not require additional parameters for operation. Frame Relay DLCI Mappings If you are connecting to another Compatible Systems router, this information is not required for Frame Relay operation. Compatible Systems uses IARP (Inverse Address Resolution Protocol) to dynamically generate this information. -
Page 13: Ip Protocol
Note: Due to the complexity of BGP, configuration parameters for BGP are not given in this Quickstart. For help with BGP configuration parameters, and other configuration questions, refer to theTech Support pages on the Compatible Systems Web site at: http://www.compatible.com/. -
Page 14: Suggested For Ipx
Chapter 2 - Quickstart Configuration TB: Use configure and set the Numbered and Net keywords in the IPX WAN 0 section. Suggested for IPX The settings above are all that is generally required for IPX operation over Frame Relay. AppleTalk Protocol Required for AppleTalk Frame Relay operation requires that the WAN interface be set as a “numbered interface.”... -
Page 15: Smds Configuration
Frame Relay operation. The only parameters which should be set differently for SMDS are the Link Configuration and the SMDS addressing section. Link Configuration SMDS is presently supported in the DS3-10/100 RIOP only via synchronous dedicated line operation. •... -
Page 16: Chapter 3 - Shipping Defaults
Chapter 3 - Shipping Defaults Ethernet Interface IP Routing Defaults • • • • • IPX Routing Defaults • • • • AppleTalk Routing Defaults • • DECnet Defaults • WAN Interface IP Defaults • • • • IPX Defaults •... -
Page 17: Chapter 4 - Led Patterns
In addition to indicating certain router-wide operating conditions and they may also display port-specific information. v Note : Any continuous flashing pattern not noted in this chapter may be caused by a hard- ware failure. Please call Compatible Systems Technical Support if your router shows a hard- ware failure. Router LED Patterns The following LEDs and light patterns provide information about the VSR’s physical state and... -
Page 18: Ethernet Traffic Indicators
Chapter 4 - LED Patterns DS3-10/100 RIOP LED Patterns The following LEDs and light patterns provide information about the DS3-10/100 RIOP inter- faces. Ethernet Traffic Indicators Scan from 1 to 3: Ethernet transmit packet Scan from 5 to 3: Ethernet receive packet...