Table of Contents
Advertisement
Quick Links
INSTRUCTION MANUAL
Save these instructions for future reference. For
assistance:
PLEASE CONTACT WAL-MART STORES INC. USA at
833-971-0570
INGROUND
BASKETBALL SYSTEM
MODEL NUMBER/STYLE
Inground Basketball System
Item No.:UGO-20433WM
Item No.:UGO-20285WM
WARNING!
READ AND UNDERSTAND
OPERATOR'S MANUAL BEFORE
USING THIS UNIT.
FAILURE TO FOLLOW OPERATING
INSTRUCTIONS COULD RESULT IN
INJURY OR DAMAGE TO PROPERTY.
Advertisement
Table of Contents
Related Manuals for NBA UGO-20433WM
Summary of Contents for NBA UGO-20433WM
- Page 1 INGROUND BASKETBALL SYSTEM INSTRUCTION MANUAL MODEL NUMBER/STYLE Inground Basketball System Item No.:UGO-20433WM Item No.:UGO-20285WM Save these instructions for future reference. For WARNING! assistance: READ AND UNDERSTAND OPERATOR'S MANUAL BEFORE USING THIS UNIT. PLEASE CONTACT WAL-MART STORES INC. USA at FAILURE TO FOLLOW OPERATING...
- Page 2 POLE CARE AND SYSTEM MAINTENANCE The life of your basketball system depends on many variables. The climate, exposure to corro- sives such as salt, pesticides or herbicides, and excessive use, or misuse can all contribute to pole failure, which may cause property damage and/or personal injury. Check your basketball system frequently for loose hardware, excessive wear, and signs of corrosion.
-
Page 3: Safety Instructions
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. -
Page 4: Year Limited Warranty
5 Year Limited Warranty Thank you for your purchase. The parts of this basketball goal (excluding nets) are covered by a 5-year Limited Warranty for defects in materials and workmanship (“Warranty”), excluding installation. Nets are expressly excluded from this Limited Warranty. In addition, you will be responsible for installation of all replacement parts. - Page 5 Warning FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for operation of the system. Only hang from the rim briefly to regain balance or avoid injuring others.
-
Page 6: Exploded Diagram
Exploded diagram Top Pole Backboard Bottom Pole Upper Arm 2PCS Anchor Plate Actuator Lower Arm 2PCS "U" shape Post Post Washer Actuator Crank 2PCS (Pre-Installed) Arm Pole Cover Top Pole Cover Pre-Installed (Pre-Installed) 4PCS... - Page 7 Bolt, Washers and Nut Bolt,Washers and Nut Bolt, Washers and Nut M10 X 120mm M8 x 130mm M10 x 40mm 2PCS 4PCS Bolt, Washers and Nut Stop Spacer F,34,35,36,37 M12 x 160mm 2PCS Anchor Bolts, Washers and Hex Locknut 4PCS Bolt, Washers and Nut Bolt, Washers and Nut Bolt, Washers and Nut...
- Page 8 INSTALLATION TIMELINE Prior to anchor system and goal assembly, call utility services for location of under- ground utility lines before you dig. Vertical main post assembly is a two part process. PART 1 PART 2 Day 1. Complete Anchor System Day 5.
- Page 9 Assemble anchor system as follows: Thread nut THESE NUTS (#35) to bottom of threads on anchor bolt (#F) insert USED FOR LEVELING threads of anchor bolt (#F) through hole on anchor plate (#8) and secure with nut (F#35). Repeat this step for the remaining anchor bolts.
- Page 10 ASSEMBLY INSTRUCTIONS (Day 5) NOTE: All board arms are made of rectangular tubing. Tightening hardware too tight may damage tubing and make adjustment of system difficult. STEP 1 Warning! Four adults required for assembly. Align the Top Pole (#2) with the bottom pole (#1) as shown in Figure 3 and slide them together. (pre installed) Figure 3...
- Page 11 Warning! Four adults STEP 2 required for assembly. Align the "U" shape Post (#11) with the two Post washers (#12) and bottom pole (#1) as shown in Figure 4, secure using one Screw set(#A) and two Screw sets(#B). See Figure 3.Tighten bolts tight.
- Page 12 Warning! Four adults STEP 3 required for assembly. Attach lower arms (#7) to Top Pole (#2), as shown in Figure 5, using a hex bolt (#H), four flat washers, two lock nuts. Attach upper arms (#6) to Top Pole (#2), as shown in Figure 5, using a hex bolt (#H), four flat washers, two lock nuts.
- Page 13 STEP 5 Warning! Four adults required for assembly. Insert the Bolt (#D) through the washer, the Lower Arm (#7), a Stop Spacer (#E), the Actuator (#9), the other Stop Spacer (#E), the other Lower Arm (#7), the washer and the lock nut in order.
- Page 14 Warning! Four adults required for assembly. Figure 8 STEP 7 Assemble the Rim (#4) to Backboard (#3), as shown in Figure 8, using two bolts (#O), two washers, and two lock nuts for upper two holes ,two bolts (#G), two washers, (Upper) and two lock nuts for lower two holes.
- Page 15 STEP 9 Warning! Four adults required for assembly. With at least three capable people, raise the backboard assembly up and have the fourth attach Lower Arms(#7) to lower mounting Plate on backboard using two bolts (#C), two wash - ers, and two lock nuts. See Figure 10. And then have the fourth attach Upper Arms(#6) to Upper mounting Plate on backboard using two bolts (#C), two washers, and two lock nuts.
- Page 16 STEP 10 Warning! Four adults required for assembly. Locate hardware needed to mount pole to anchor bolts. You will need, four flat washers (#37), four lock washers (#36), four nuts (#35), four hex round nuts (#34) Note: Do not remove the nuts (#35) you installed in step 2 (pg.8). CAUTION PLACING THE POST ON THE ANCHOR SYSTEM REQUIRES AT...
-
Page 17: Care Information
STEP 12 Warning! Four adults required for assembly. If further leveling is required, loosen top #35 nuts but do not loosen past the top of # 34 Bolt. DO NOT REMOVE NUTS # 35. Place a level on pole and adjust bottom nuts #35 with a wrench until pole is level. - Page 18 Warning! Four adults required for assembly.
-
Page 19: Complete View
Complete View Warning! Four adults required for assembly.