Electro-Voice EVID Series Owner's Manual page 7

Product Description Product Description
Step 2: Select Wattage Tap Step 2: Select Wattage Tap
(Models 4.2t and 6.2t Only) (Models 4.2t and 6.2t Only)
Before mounting the speaker to the Before mounting the speaker to the
bracket, select the proper wattage tap bracket, select the proper wattage tap
setting for your installation. The wattage setting for your installation. The wattage
selector switch is located at the rear of the selector switch is located at the rear of the
speaker below the input terminal panel. speaker below the input terminal panel.
The EVID™ 4.2t and 6.2t include a switch The EVID™ 4.2t and 6.2t include a switch
for selecting the power taps. The EVID™ for selecting the power taps. The EVID™
3.2t has a single power tap. 3.2t has a single power tap.
EVID™ 3.2t EVID™ 3.2t
A single (non-selectable) power tap rated A single (non-selectable) power tap rated
at 5W@70V and 10W@100V. at 5W@70V and 10W@100V.
EVID™ 4.2t EVID™ 4.2t
The power taps are 30W, 15W and 7.5W The power taps are 30W, 15W and 7.5W
at both 70.7V and 100V, with a 3.7W tap at both 70.7V and 100V, with a 3.7W tap
for 70.7V only, as well as an 8 ohm for 70.7V only, as well as an 8 ohm
transformer bypass setting. transformer bypass setting.
EVID™ 6.2t: EVID™ 6.2t:
The power taps are 60W, 30W and 15W The power taps are 60W, 30W and 15W
at both 70.7V and 100V, with a 7.5W tap at both 70.7V and 100V, with a 7.5W tap
for 70.7V only, as well as an 8 ohm for 70.7V only, as well as an 8 ohm
transformer bypass setting. transformer bypass setting.
The taps for the models listed above are The taps for the models listed above are
selected by a rotary switch on the back selected by a rotary switch on the back
panel. A panel. A guide on the guide on the
speaker shows which switch positions to speaker shows which switch positions to
use for the power settings at 70V and use for the power settings at 70V and
100V. 100V.
Figure 8 below illustrates the settings for Figure 8 below illustrates the settings for
the 4.2t and 6.2t. the 4.2t and 6.2t.
4.2t 4.2t
Figure 8: Figure 8:
EVID EVID TM TM Owner's Manual Owner's Manual
back of each back of each
6.2t 6.2t
Wattage Taps (4.2t & 6.2t) Wattage Taps (4.2t & 6.2t)
Step 3: Mount the Speaker to the Step 3: Mount the Speaker to the
SAM™ Bracket SAM™ Bracket
Attach the speaker to the SAM™ bracket Attach the speaker to the SAM™ bracket
with the socket head bolt B, as shown in with the socket head bolt B, as shown in
Figure 9. Figure 9.
Figure 9: Figure 9: Tighten Socket Head Bolts Tighten Socket Head Bolts
Using the provided security tool, tighten Using the provided security tool, tighten
the two socket head bolts shown in Fig. the two socket head bolts shown in Fig.
9. 9. Select the Select the proper horizontal proper horizontal
secure it by tightening Bolt A to the proper secure it by tightening Bolt A to the proper
torque listed torque listed in Fig. 10. in Fig. 10.
proper vertical angle and secure it by proper vertical angle and secure it by
tighte tightening Bolt B. ning Bolt B. Use the Use the
markers as your guide (see Fig. 9). Attach markers as your guide (see Fig. 9). Attach
both logo caps as shown in Figure 11 both logo caps as shown in Figure 11
after tightening and securing the speaker. after tightening and securing the speaker.
M M o o d d e e l l T T o o r r q q u u e e
E E V V I I D D 3 3 . . 2 2 20-3 -30 i 20 0 in- n-lb lbs (
E E V V I I D D 4 4 . . 2 2 30-5 -50 i 30 0 in- n-lb lbs (
E E V V I I D D 6 6 . . 2 2 70-9 -90 i 70 0 in- n-lb lbs (
Figure 10: Figure 10: Recommended Torque Recommended Torque
Settings for Bolt A Settings for Bolt A
EV logo cap EV logo cap
(large) (large)
Figure 11: Figure 11: Attach Logo Caps Attach Logo Caps
Bolt A Bolt A
(swing) (swing)
Bolt B Bolt B
(rotation) (rotation)
15˚ angle markers 15˚ angle markers
angle and angle and
Then selec Then select the t the
15° 15° angle angle
s (2. 2.3- 3-3 3 .4 .4 N N -m) -m )
s (3. 3.4- 4-5 5 .2 .2 N N -m -m) )
s (7. 7.9- 9-1 1 0. 0.2 N 2 N-m -m) )
EV logo cap EV logo cap
(small) (small)
5 5