MQ Power WHISPERWATT Series Operation Manual
  1. Manuals
  2. Brands
  3. MQ Power Manuals
  4. Portable Generator
  5. WHISPERWATT Series
  6. Operation manual

MQ Power WHISPERWATT Series Operation Manual

60hz generator deep sea controller
Hide thumbs Also See for WHISPERWATT Series:
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATION MANUAL
WHISPERWATT™ SERIES
MODEL DCA70SSIU4F
60Hz GENERATOR
DEEP SEA CONTROLLER
DSE8610 MKII-U2
(ISUZU BR-4JJ1X DIESEL ENGINE)
Revision #0 (08/11/22)
To find the latest revision of this publication or
associated parts manual, visit our website at:
www.mqpower.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

Advertisement

Table of Contents
loading

Related Manuals for MQ Power WHISPERWATT Series

Summary of Contents for MQ Power WHISPERWATT Series

  • Page 1 OPERATION MANUAL WHISPERWATT™ SERIES MODEL DCA70SSIU4F 60Hz GENERATOR DEEP SEA CONTROLLER DSE8610 MKII-U2 (ISUZU BR-4JJ1X DIESEL ENGINE) Revision #0 (08/11/22) To find the latest revision of this publication or associated parts manual, visit our website at: www.mqpower.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

  • Page 2: Proposition 65 Warning

    PROPOSITION 65 WARNING PAGE 2 — DCA70SSIU4F 60 HZ GENERATOR DSE8610 MKII • OPERATION MANUAL — REV. #0 (08/11/22)

  • Page 3: Table Of Contents

    TABLE OF CONTENTS DCA70SSIU4F DSE8610 MKII Controller 60 Hz Generator Proposition 65 Warning ........... 2 Safety Decals ............4 Safety Information ..........5–10 Specifications ............11 Dimensions ............12 Installation ............14–15 General Information ..........16 Major Components ..........17 Control Panel ............

  • Page 4: Safety Decals

    SAFETY DECALS SAFETY DECALS NOTICE Safety decals are attached to the generator as shown in For safety decal part numbers, refer to the DCA70SSIU4F Figure 1. Keep these safety decals clean at all times. When Aggreko parts manual. the safety decals become worn or damaged, contact your nearest dealer or the Multiquip Parts Department.

  • Page 5: Safety Information

    SAFETY INFORMATION Do not operate or service the generator before reading the Potential hazards associated with the operation of this entire manual. Safety precautions should be followed at all generator will be referenced with hazard symbols which times when operating this generator. Failure to read and may appear throughout this manual in conjunction with understand the safety messages and operating instructions safety messages.
  • Page 6 „ NEVER use accessories or attachments that are not being used. The generator should be stored in a clean, dry location out of the reach of children and unauthorized recommended by MQ Power for this generator. Damage to the generator and/or injury to the user may result. personnel.
  • Page 7 SAFETY INFORMATION ENGINE SAFETY „ Operation of the generator may create sparks that can start fi res around dry vegetation. A spark arrestor DANGER may be required. The operator should contact local fi re agencies for laws or regulations relating to fi re prevention „...
  • Page 8 „ The trailer should be adjusted to a level position at all times when towing. „ Refer to the MQ Power trailer manual for additional safety information. „ Raise and lock the trailer wheel stand in the upright position when towing.
  • Page 9 SAFETY INFORMATION ELECTRICAL SAFETY „ Make sure power cables are securely connected to the generator’s output receptacles. Incorrect connections DANGER may cause electrical shock and damage to the generator. „ NEVER touch the output terminals NOTICE during operation. Contact with the „...
  • Page 10 SAFETY INFORMATION EMISSIONS INFORMATION „ If the battery liquid (dilute sulfuric acid) comes into contact with eyes, rinse eyes immediately with plenty NOTICE of water and contact the nearest doctor or hospital to seek medical attention. The diesel engine used in this equipment has been designed to reduce harmful levels of carbon monoxide CAUTION (CO), hydrocarbons (HC), and nitrogen oxides (NOx)

  • Page 11: Specifications

    SPECIFICATIONS Table 1. Generator Specifications Model DCA70SSIU4F Type Revolving field, self-ventilated, protected type synchronous generator Armature Connection Star with Neutral Zigzag Phase 3Ø 1Ø Standby Output 62 kW (77 kVA) 44 kW Prime Output 56 kW (70 kVA) 40 kW 3Ø...

  • Page 12: Dimensions

    DIMENSIONS 6,960 lb. (3,157 kg) Figure 2. Dimensions Table 3. Dimensions Reference Dimension in. (mm) Reference Letter Dimension in. (mm) Letter 33.86 (860) 33.78 (858) 29.45 (748) 105.12 (2,670) 38.19 (970) 68.30 (1,735) 32.28 (820) 37.40 (950) PAGE 12 — DCA70SSIU4F 60 HZ GENERATOR DSE8610 MKII • OPERATION MANUAL — REV. #0 (08/11/22)
  • Page 13 NOTES DCA70SSIU4F 60 HZ GENERATOR DSE8610 MKII • OPERATION MANUAL — REV. #0 (08/11/22) — PAGE 13...

  • Page 14: Installation

    GROUND LUG GROUND ROD GROUND CABLE REFERENCE NEC 250 Figure 3. Typical Generator Grounding Application NOTICE Trailer-mounted generators are the sole responsibility of MQ Power. PAGE 14 — DCA70SSIU4F 60 HZ GENERATOR DSE8610 MKII • OPERATION MANUAL — REV. #0 (08/11/22)
  • Page 15 INSTALLATION OUTDOOR INSTALLATION MOUNTING Install the generator in an area that is free of debris, The generator must be mounted on a solid foundation bystanders, and overhead obstructions. Make sure the (such as concrete) and set firmly on the foundation to generator is on secure, level ground so that it cannot slide isolate vibration of the generator when it is running.

  • Page 16: General Information

    CONTROL BOX Reference Table 2 for engine specifications. In keeping with MQ Power’s policy of constantly improving The “Control Panel” is provided with the following: „ Current Transformers its products, the specifications quoted herein are subject to „...

  • Page 17: Major Components

    MAJOR COMPONENTS Table 4. Generator Major Components ITEM NO. DESCRIPTION DOC/SCR Assembly DEF Tank Assembly Coolant Drain Plug Oil Drain With Valve Fuel Tank Assembly Battery Assembly CIRCUIT BREAKER Air Filter Assembly DEEP SEA ELECTRONICS DSE 8610 MKII-U2 REMOTE START BASELOAD MAIN CONFIG Voltage Selector Switch Assembly...

  • Page 18: Control Panel

    CONTROL PANEL CIRCUIT BREAKER DEEP SEA ELECTRONICS DSE 8610 MKII-U2 REMOTE START BASELOAD MAIN CONFIG COMMON ALARM PANEL LIGHTS 3 PHASE DSE8610 MK2 CONTROL BUTTON CIRCUIT BREAKER MAIN BREAKER DSE 8610 MKII-U2 REMOTE START MENU BASE LOAD STATUS DISPLAY NAVIGATOR MAIN CONFIG COMMON ALARM 3 PHASE...
  • Page 19 NOTES DCA70SSIU4F 60 HZ GENERATOR DSE8610 MKII • OPERATION MANUAL — REV. #0 (08/11/22) — PAGE 19...
  • Page 20 DSE8610 MKII-U2 DEEP SEA CONTROLLER DEEP SEA ELECTRONICS DSE 8610 MKII-U2 REMOTE START BASELOAD MAIN CONFIG COMMON ALARM AUTO 14 13 Figure 6. DSE8610 MKII Controller The definitions below describe the controls and functions 3. LCD Display — This backlit display serves as the local information source for metering, alarms, pre-alarms, of the DSE8610 MKII Deep Sea Controller (Figure 6).
  • Page 21 DSE8610 MKII-U2 DEEP SEA CONTROLLER 7. Start Button — Only active in the Stop/Reset and use the close To run the generator with a load applied, Manual modes. Pressing the Start button in Stop/Reset contactor button. Once the generator is stable, up to Mode powers up the engine’s ECU but does not start speed and has the desired voltage, press the close the engine.

  • Page 22: Output Terminal Panel Familiarization

    OUTPUT TERMINAL PANEL FAMILIARIZATION OUTPUT TERMINAL PANEL OUTPUT TERMINAL FAMILIARIZATION The Output Terminal Panel (Figure 7) shown below is The “Output Terminal Panel” (Figure 7) is provided with located on the right-hand side (left from the control panel) the following: of the generator.
  • Page 23 OUTPUT TERMINAL PANEL FAMILIARIZATION 120 VAC GFCI Receptacles Each auxiliary receptacle is protected by a 50-amp circuit breaker. These breakers are located directly above the NOTICE GFCI receptacles. Remember the load output (current) on both receptacles is dependent on the load requirements of It is recommended that the GFCI receptacles be tested the output terminal lugs.
  • Page 24 OUTPUT TERMINAL PANEL FAMILIARIZATION Connecting Loads Overcurrent Relay An overcurrent relay (Figure 12) is connected to the main Loads can be connected to the generator by various methods, output terminal lugs, camlocks or the convenience circuit breaker. In the event of an overload, both the circuit receptacles (Figure 11).

  • Page 25: Load Application

    LOAD APPLICATION SINGLE-PHASE LOAD THREE-PHASE LOAD Always be sure to check the nameplate on the generator When calculating the power requirements for 3-phase and equipment to ensure the wattage, amperage, frequency, power use the following equation: and voltage requirements are satisfactorily supplied by the VOLTAGE ×...

  • Page 26: Generator Outputs

    GENERATOR OUTPUTS GENERATOR OUTPUT VOLTAGES Maximum Amps Table 8 shows the maximum amps the generator can A wide range of voltages are available to supply voltage for many different applications. Voltages are selected by using provide. DO NOT exceed the maximum amps as listed. the voltage selector switch (Figure 13).

  • Page 27: Output Terminal Panel Connections

    OUTPUT TERMINAL PANEL CONNECTIONS UVWO TERMINAL OUTPUT VOLTAGES 3Ø-208V/1Ø-120V UVWO Terminal Output Voltages 1. Place the voltage selector switch in the 3Ø 240/139 Various output voltages can be obtained using the UVWO position as shown in Figure 14. output terminal lugs. The voltages at the terminals are 2.
  • Page 28 OUTPUT TERMINAL PANEL CONNECTIONS 2. Connect the load wires to the UVWO terminals as 2. Connect the load wires to the UVWO terminals as shown in Figure 18. shown in Figure 20. BLUE GREEN BLACK WHITE BLACK BLUE GREEN WHITE NOT USED 277V 480V...

  • Page 29: Inspection/Setup

    INSPECTION/SETUP ENGINE OIL CHECK 5. If the engine oil level is low (Figure 22C), remove the oil filler cap (Figure 23) and fill to a safe operating level NOTICE (max) as indicated by the dipstick (Figure 22A). This Isuzu engine is equipped with a low oil shutdown NOTICE capability.
  • Page 30 INSPECTION/SETUP FUEL CHECK REFUELING PROCEDURE: WARNING DANGER Diesel fuel and its vapors are dangerous Fuel spillage on a hot engine can cause to your health and the surrounding a fire or explosion. If fuel spillage occurs, environment. Avoid skin contact and/or wipe up the spilled fuel completely to inhaling fumes.
  • Page 31 INSPECTION/SETUP DEF REFUELING 3. NEVER overfill the fuel tank — It is important to read the fuel gauge when filling the trailer fuel tank. DO NOT NOTICE wait for fuel to rise in the filler neck (Figure 27). ONLY fill the DEF tank with diesel exhaust fluid. Any FUEL GAUGE LOCATED other type of fluid may cause severe engine damage.
  • Page 32 INSPECTION/SETUP COOLANT Operation in Freezing Weather (ANTIFREEZE/SUMMER COOLANT/WATER) When operating in freezing weather, be certain the proper amount of antifreeze (Table 13) has been added. Isuzu recommends antifreeze/summer coolant for use in their engines, which can be purchased in concentrate (and mixed Table 13.
  • Page 33 INSPECTION/SETUP AIR CLEANER Table 14. Fan Belt Deflection Standard Value Standard Value Periodic cleaning/replacement of the air cleaner is Belt (Amount of Deflection) (Vibration Frequency) necessary. Inspect the air cleaner (Figure 32) in accordance with the maintenance section of this manual or the Isuzu 0.17–0.20 in.
  • Page 34 INSPECTION/SETUP Battery Cable Installation ALTERNATOR ALWAYS be sure the battery cables (Figure 34) are The polarity of the alternator is negative grounding type. properly connected to the battery terminals as shown below. When an inverted circuit connection takes place, the The red cable is connected to the positive terminal of the circuit will be in short circuit instantaneously, resulting in battery, and the black cable is connected to the negative...

  • Page 35: Generator Start-Up Procedure (Manual)

    GENERATOR START-UP PROCEDURE (MANUAL) BEFORE STARTING STARTING (MANUAL) 1. Place the main circuit breaker in the ON position. CAUTION The engine’s exhaust contains harmful emissions. ALWAYS have adequate ventilation when operating. Direct exhaust away from nearby personnel. WARNING NEVER manually start the engine with the main, GFCI or auxiliary circuit breakers in the ON (closed) position.
  • Page 36 GENERATOR START-UP PROCEDURE (MANUAL) 4. Press the OFF and CHECK buttons simultaneously to 7. Use the UP/DOWN arrows (Figure 42) to select the enter the configuration display menu. desired output voltage. 8. Verify that the selected voltage being displayed on the Voltage Config Screen (Figure 42) is the same voltage DEEP SEA ELECTRONICS DSE 8610 MKII-U2...
  • Page 37 GENERATOR START-UP PROCEDURE (MANUAL MODE) Frequency Verification NOTICE Press the right arrow button twice and verify that the In cold weather conditions let the engine idle longer "Generator" screen is displayed, then press the down before use. arrow button three times and verify that the 60-cycle 14.
  • Page 38 GENERATOR START-UP PROCEDURE (MANUAL MODE) Load Current Verification From the main status screen, press the right arrow button DEEP SEA ELECTRONICS DSE 8610 MKII-U2 twice and verify that the "Generator" screen is displayed, Engine Oil Pressure REMOTE START then press the down arrow button four times and verify BASELOAD MAIN CONFIG that the generator’s load current screen is displayed in...
  • Page 39 GENERATOR START-UP PROCEDURE (MANUAL MODE) Engine Speed Verification DEF Level Verification (If Applicable) From the main status screen, press the right arrow button From the main status screen, press the right arrow button once and verify that the "Engine" screen is displayed, then once and verify that the "Engine"...
  • Page 40 GENERATOR START-UP PROCEDURE (MANUAL MODE) Additional Engine Operating Parameters From the main status screen, press the right arrow button once and verify that the "Engine" screen is displayed Additional engine parameters such as the ones shown below can be accessed by pressing the down arrow button „...

  • Page 41: Generator Start-Up Procedure (Auto Mode)

    GENERATOR START-UP PROCEDURE (AUTO MODE) STARTING (AUTO MODE) When starting the generator in AUTO mode use the “Manual Start-Up” procedure except where noted (see DANGER below). Before connecting this generator to any 1. Perform steps 1 through 4 in the "Before Starting" building’s electrical system, a licensed section and steps 1 through 3 in the "Manual Starting"...

  • Page 42: Generator Shutdown Procedure

    GENERATOR SHUTDOWN PROCEDURE NORMAL SHUTDOWN PROCEDURE WARNING NEVER stop the engine suddenly except in an emergency. To shut down the generator, use the following procedure: Figure 64. Off Button (Manual Mode) 1. Place the load's ON/OFF switch in the OFF position. 1.
  • Page 43 GENERATOR START-UP PROCEDURES (PARALLEL OPERATION) GENERATOR 1 GENERATOR 2 GENERATOR 3 Figure 66. MSC Communication Cable Connections (Three or More Generators) DCA70SSIU4F 60 HZ GENERATOR DSE8610 MKII • OPERATION MANUAL — REV. #0 (08/11/22) — PAGE 43...
  • Page 44 GENERATOR START-UP PROCEDURES (PARALLEL OPERATION) MANUAL PARALLEL OPERATION (2 OR MORE Preparation UNITS) NOTICE NOTICE Make sure the engines of all generator units in the To ensure stable operation of multiple generator units system are turned OFF before connecting the units. connected in parallel and working as one unit, it is necessary to maintain equal voltage, frequency, and 1.
  • Page 45 GENERATOR START-UP PROCEDURES (PARALLEL OPERATION) 5. For the two outer most generators place the parallel 10. From the "Alt Config Menu (Figure 41), verify that the signal switch (Figure 67) in the END position. "VOLTAGE CONFIG" screen (Figure 71) is displayed. Figure 67.
  • Page 46 GENERATOR START-UP PROCEDURES (PARALLEL OPERATION) 18. Repeat step 17 for all remaining generators. The engine speed is automatically adjusted, altering the phase until the moving bar enters the center of the scope 19. Allow all generators to synchronize. This synchronization (Figure 75).
  • Page 47 GENERATOR START-UP PROCEDURES (PARALLEL OPERATION) 7. Press the AUTO button (Figure 80) on all controllers in the system. DEEP SEA ELECTRONICS DSE 8610 MKII-U2 Editor - Display REMOTE START BASELOAD Contrast AUTO AUTO MAIN CONFIG COMMON ALARM Figure 80. Auto Button 8.

  • Page 48: Maintenance

    MAINTENANCE 500 Hrs. 3,000 Hrs 10 Hrs. Table 16. Inspection/Maintenance 250 Hrs. or Every or Every OTHER DAILY 12 Months 36 Months Check Engine Oil and Coolant Levels Check Fuel Filter/Water Separator Bowl Check Air Cleaner/Element Clean Air Cleaner/Element Check for Leaks/Hoses/Clamps Check for Loosening of Parts Change Engine Oil and Oil Filter * Clean Unit, Inside and Outside...
  • Page 49 MAINTENANCE GENERAL INSPECTION Primary and Secondary Air Cleaner Elements Prior to each use, the generator should be cleaned and 1. Release the latches (Figure 81) that secure the cover inspected for deficiencies. Check for loose, missing or to the air cleaner body. damaged nuts, bolts or other fasteners.
  • Page 50 MAINTENANCE Air Filter Dust Indicator NOTICE AIR BLEEDER PLUG The air filter should not be changed until the indicator FILTER BODY reads RED. Dispose of the old air filter. It may not be cleaned or reused. FUEL FILTER DRAIN PLUG The air filter indicator (Figure 82) is attached to the air filter.
  • Page 51 MAINTENANCE FUEL FILTER ELEMENT REPLACEMENT ELECTROMAGNETIC FUEL PUMP (500 HOURS) 1. Use a filter wrench to remove the element case The filter inside the fuel pump (Figure 85) is either a paper (Figure 84) from the fuel filter body. type or steel mesh type depending on the fuel pump type. Clean or replace the fuel pump filter as follows: 1.
  • Page 52 MAINTENANCE DRAINING THE CONTAINMENT TANK CLEANING INSIDE THE FUEL TANK 1. This generator is equipped with an environmental If necessary, drain the fuel inside the fuel tank completely. containment tank. Inspect this tank regularly. Using a spray washer (Figure 87) wash out any deposits or debris that have accumulated inside the fuel tank.
  • Page 53 MAINTENANCE DRIVE BELT (DAILY) DRAINING ENGINE OIL Drive Belt Tension 1. Run the engine until the engine coolant reaches a temperature of 140°F (60°C). Turn the engine off. A slack drive belt (Figure 88) may contribute to overheating 2. Remove the oil dipstick from its holder. or insufficient charging of the battery.
  • Page 54 MAINTENANCE ENGINE OIL FILTER REPLACEMENT DRAINING ENGINE COOLANT WARNING 1. Clean the area around the lubricating oil filter head. 2. Using an oil filter wrench (Figure 90), remove the DO NOT remove the pressure cap from the engine oil filter. radiator when the engine is hot! Wait until the coolant temperature is below 120°F (50°C) before removing the pressure cap.
  • Page 55 MAINTENANCE FLUSHING OUT THE RADIATOR TESTING THE GFCI RECEPTACLE AND REPLACING COOLANT NOTICE „ Open both cocks located at the crankcase side and at The GFCI receptacle is designed to interrupt power the lower part of the radiator and drain the coolant. Open when a ground fault exists to prevent injuries and shock the radiator cap while draining.
  • Page 56 MAINTENANCE GENERATOR STORAGE 4. Press the TEST button (Figure 96) on the GFCI receptacle and verify that the status LED turns OFF. For long-term storage of the generator the following is recommended: „ Drain the fuel tank completely. Treat with a fuel stabilizer if necessary.
  • Page 57 MAINTENANCE ENGINE BLOCK HEATER AND When using the generator in hot climates there is no reason to apply power to the engine block heater. However, if the INTERNAL BATTERY CHARGER generator will be used in cold climates it is always a good 120 VAC INPUT RECEPTACLES idea to apply power to the engine block heater at all times.
  • Page 58 MAINTENANCE EMISSION CONTROL EMISSION CARBON CHECK The emission control system employed with the Isuzu Deposition of carbon (soot, unburned fuel) in the exhaust BR-4JJ1X diesel engine consists of a Diesel Oxidation pipe line and muffler could cause not only system derates Catalyst (DOC).
  • Page 59 MAINTENANCE SELECTIVE CATALYTIC REDUCTION (SCR) SCR SYSTEM PURGE GUIDELINES Auto Purge Operation Diesel engines can be run with a lean burn air-to-fuel ratio, to ensure the full combustion of soot and to prevent the The auto purge operation process will be performed exhaust of unburnt fuel.
  • Page 60 MAINTENANCE Shown below in Table 17 are the regeneration symbols. These symbols show the various ECU functions. The symbols flash at different rates to show the status of the ECU function. For more detailed information refer to the engine manufacturer owners manual. Table 17.
  • Page 61 MAINTENANCE DIESEL EXHAUST FLUID (DEF) If the diesel exhaust fluid (DEF) symbol (Figure 102) is DEEP SEA ELECTRONICS displayed during Deep Sea controller operation, it indicates DSE 8610 MKII-U2 DEF Tank Level the following: REMOTE START 10 % BASELOAD MAIN CONFIG „...
  • Page 62 MAINTENANCE PROTECTION DEVICES Before attempting to restart the generator, press the OFF button on the Deep Sea controller and place all circuit Automatic Shutdown System breakers in the OFF position. This unit is equipped with engine protection devices that Allow sufficient time for adequate cooling of the generator automatically shut down the engine.

  • Page 63: Troubleshooting (Generator)

    TROUBLESHOOTING (GENERATOR) Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a breakdown, use Table 19 shown below for diagnosis of the generator. If the problem cannot be remedied, consult our company’s business office or service plant. Table 19.

  • Page 64: Troubleshooting (Engine)

    TROUBLESHOOTING (ENGINE) Troubleshooting (Engine) Symptom Possible Problem Solution No fuel reaching injection pump? Add fuel. Check entire fuel system. Defective fuel pump? Replace fuel pump. Fuel fi lter clogged? Replace fuel fi lter and clean tank. Faulty fuel supply line? Replace or repair fuel line.
  • Page 65 TROUBLESHOOTING (ENGINE) Troubleshooting (Engine) - continued Symptom Possible Problem Solution Air fi lter blocked? Clean or replace air fi lter. Low engine power output and low speed, Incorrect valve clearances? Adjust valves per engine specifi cation. black exhaust smoke. Malfunction at injector? See engine manual.

  • Page 66: Generator Wiring Diagram (Ee62815)

    GENERATOR WIRING DIAGRAM (EE62815) Ｏ Ｗ Ｖ Ｕ GENERATOR WIRING DIAGRAM EE62815 ＴＯ Ｌ （ＷＢ） ＳＷ“２０，２４，２８” Ｗ （ＶＢ） Ｒ （ＵＢ） ABB AF 400 CONTACTOR 240VAC COIL DEEPSEA W/GR GR/L FROM CBR "3" 8610 ５．５ ５．５ GR/B FROM CBR "6" CONTROLLER 240VAC ＴＯ　Ｅｎｇ.　Ｗｉｒｉｎｇ...

  • Page 67: Engine Wiring Diagram (Ee62814)

    ENGINE WIRING DIAGRAM (EE62814) ENGINE WIRING DIAGRAM EE62814 R/GR FUEL SENDER COMM DCA70SSIU4F 60 HZ GENERATOR DSE8610 MKII • OPERATION MANUAL — REV. #0 (08/11/22) — PAGE 67...

  • Page 68: Battery Charger Wiring Diagram

    BATTERY CHARGER WIRING DIAGRAM BLACK 14 AWG. LINE (L)120VAC INPUT WHITE 14 AWG. NEUTRAL (N) GREEN 14 AWG. GROUND (G) TO CHASSIS GROUND BATTERY CHARGER GREEN 16 AWG. TO STARTER “B” TERMINAL RED 16 AWG. 120 VAC INPUT, INSERT EXTERNAL POWER CORD HERE.
  • Page 69 NOTES DCA70SSIU4F 60 HZ GENERATOR DSE8610 MKII • OPERATION MANUAL — REV. #0 (08/11/22) — PAGE 69...
  • Page 70 © COPYRIGHT 2022, MULTIQUIP INC. Multiquip Inc , the MQ logo and the MQ Power logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission.

This manual is also suitable for:

Dca70ssiu4fDse8610 mkii-u2

Table of Contents