JVC TM-H1900G Instructions Manual page 6

HOW TO USE THE MENU
FUNCTIONS
(cont'd)
DISPLAY AND SELECTIONS IN THE <SET-UP
MENU> MODE (SETTING)
You can set the following set-up menu items.
• PICTURE SUB ADJ. • WHITE BALANCE • REMOTE SYSTEM
• H. POSITION • CONTROL LOCK • INPUT REMOTE
• V. POSITION • STATUS DISPLAY
Notes:
● Parameters for PICTURE SUB ADJ., H. POSITION and V. POSITION can be set
separately depending on the signal (Input A (VIDEO), Input B (VIDEO) or Input B (Y/
C)) selected with the input select buttons on the front panel.
Select the required video input with the input select buttons on the front panel in
advance.
● WHITE BALANCE can be set independently at 6500 or 9300 for the color temperature
value.
Set COLOR TEMP. to 6500 or 9300 on the <MENU> screen beforehand.
● INPUT REMOTE is shown when REMOTE SYSTEM is set to MAKE.
1. While pressing the MENU button, press the
CHROMA/PHASE button.
CHROMA MENU
The <SET-UP MENU> screen is displayed.
PHASE
2. Press the CHROMA/PHASE or CONTRAST/BRIGHT
button to select the desired menu item.
A selection mark (4) is put next to the selected item.
CHROMA CONTRAST
Front panel Function
button displayed
PHASE BRIGHT
CHROMA/
Forward selection mark (
PICTURE SUB ADJ.
PHASE
H. POSITION
CONTRAST/
Reverse selection mark (
V. POSITION
BRIGHT
WHITE BALANCE
CONTROL LOCK
STATUS DISPLAY
REMOTE SYSTEM
INPUT REMOTE
3. Press the VOLUME/SELECT buttons to set.
VOLUME/SELECT
Front panel Function
button displayed
+ Increase (to max. value)
VOLUME/
4 Forward the setting value
SELECT (+)
CUTO Selects CUT OFF setting screen
– Decrease (to min. value)
VOLUME/
1 Reverse the setting value
SELECT (–)
DRV Selects DRIVE setting screen
Notes:
● For WHITE BALANCE items, select the CUT OFF or DRIVE
setting screen, then select the function display for adjustment.
● Press the EXIT (MENU) button to return to the <SET-UP
MENU> screen.
10
<SET-UP MENU> screen
1
<SET-UP MENU>
4 PICTURE SUB ADJ.
H. POSITION : 00
V. POSITION : 00
WHITE BALANCE
CONTROL LOCK : OFF
STATUS DISPLAY : ON
REMOTE SYSTEM : MAKE
INPUT REMOTE : A – B
2
EXIT
CHROMA CONTRAST VOLUME/SELECT MENU
PHASE BRIGHT
<Front panel buttons>
1
Selection mark (4): Indicates the
menu item you select.
2
Menu item: Menu items you can
select.
3
Setting display: Indicates the
current settings (value).
4
Function display: The functions of
the front panel buttons (5 buttons
on the left) correspond to the
function displayed.
Function
Contents
displayed
Contents
Forward the menu item.
Reverse the menu item.
4 )
– Lower the adjustment
value. (to the minimum)
4 )
+ Raise the adjustment
value. (to the maximum)
4
Forward the setting value.
1
Reverse the setting value.
Exit the <MENU>
EXIT
screen.
DRV Selects DRIVE adjustment.
Selects CUT OFF
CUTO
adjustment.
Contents
Adjusts red and blue
RB
signal level.
Adjusts red, green and
RGB
blue signal level.
Turns the ON-SCREEN
display on or off. (This
DISP function is effective only
in the DRIVE or CUT OFF
adjustment mode.)
Set-up menu items
PICTURE SUB ADJ. Image sub adjustment
CONTRAST Adjusts contrast.
BRIGHT Adjusts brightness.
CHROMA Adjusts color density.
PHASE Adjusts hue.
H. POSITION Adjusts the horizontal position of the
screen (+: Horizontal position shifts
to the right/-: Horizontal position shifts to
the left)
V. POSITION Adjusts the vertical position of the screen
(+: Vertical position moves up/-: Vertical
position moves down)
WHITE BALANCE Adjusts the white balance.
DRIVE R. DRIVE Adjusts red level.
3
B. DRIVE Adjusts blue level.
4
CUT OFF R. CUT OFF Adjusts red cut off.
G. CUT OFF Adjusts green cut off.
B. CUT OFF Adjusts blue cut off.
CONTROL LOCK Sets the operation buttons on the front
panel to control lock mode.
STATUS DISPLAY Sets the status display of the color system.
REMOTE SYSTEM Sets the external control function method.
INPUT REMOTE Sets external control of input selection.
(Shown only when REMOTE SYSTEM is
set to MAKE.)
*1 May not be shown depending on the type of signals input.
*2 Refer to HOW TO USE EXTERNAL CONTROL on page 15 for more details.
4. To set the other set-up menu items, repeat the
procedures 2 and 3.
5. Press the MENU button to quit.
Front panel
MENU
button
MENU
Note:
Setting Description
MAKE Make contact system: Controls the function using the control
terminal's short-circuit and open (short-circuits or opens 15th
terminal (GND)).
TRG. Trigger system: Controls the function by short-circuiting (short-
circuits or opens 15th terminal (GND)) with pulse (about 1 sec.)
A-B Switches the input by short-circuiting a specified signal line in
INPUT A or B.
A/B Switches between INPUT A and INPUT B with D-sub pin 2.
Purpose Settings
Selects CONTRAST/BRIGHT/CHROMA/PHASE. The
selected setting screen is shown. Select the function display for
adjustment.
–10 –9 • • –01 00 + 01 • • + 09
+ 01 + 09
–10 –9 • • –01 00 • •
–10 –9 –01 00 + 01 + 09
*1 • • • •
–10 –9 –01 + 01 + 09
*1 • • 00 • •
+ 1
– 5 • • • – 01 00 • • •
+ 1
–5 • • • –01 00 • • •
Selects the drive (DRV) or cut off (CUTO) adjustment. The selected
setting screen is shown. Select the function display for adjustment.
– 20 – 1 9 – 01 + 01 + 19
• • 00 • •
+ 01 + 19
–20 –19 • • –01 00 • •
–20 –19 –01 00 + 01 • • + 19
• •
–20 –19 • • –01 00 + 01 • • + 19
– 20 – 1 9 • • – 01 00 + 01 • • + 19
OFF ON
OFF ON
M A K E T R G .
A–B A / B
Notes:
● When the CONTROL LOCK function
is set to ON, pressing operation
buttons on the front panel will display
the message "CONTROL LOCK ON!"
on the screen for about 3 seconds.
● The CONTROL LOCK function is
maintained even when the power is
turned off.
● To turn off the CONTROL LOCK
function, while holding the MENU
Function
button press the CHROMA/PHASE
Contents
displayed button. Then set the CONTROL
LOCK function to OFF.
Quit (or Release) the <MENU> ● Even when the CONTROL LOCK
EXIT
function is set to ON, the following
screen
operations are available:
– Power Switch operation
– Volume control with the VOLUME/
SELECT buttons
– Display or disappear of the <SET-
UP MENU> screen.
● The STATUS DISPLAY function can
be set to display (ON) or not display
(OFF) the present color system when
the power is turned on or the input
signal is changed. Refer to page 7 for
more information.
● When REMOTE SYSTEM is set to
MAKE and any one of the INPUT A
and B buttons or the UNDER SCAN
button is pressed, "REMOTE ON!"
appears on screen for about 3
seconds. (Not shown with CON-
TROL LOCK set to ON.)
● When REMOTE SYSTEM is set to
TRG, the front panel controls can be
operated.
● INPUT REMOTE and REMOTE
SYSTEM are enabled when
REMOTE ENABLE is set to ON.
+ 10
+ 10
+ 10
+ 10
+ 5
+ 5
+ 20
+ 20
+ 20
+ 20
+ 20
*2
*2
11