Download
Share
Print this page
Hunter ACC2 Assembly Instructions Manual
  1. Manuals
  2. Brands
  3. Hunter Manuals
  4. Control Systems
  5. ACC2
  6. Assembly instructions manual

Hunter ACC2 Assembly Instructions Manual

Strongbox pedestal
Hide thumbs Also See for ACC2:

Advertisement

Quick Links

Download this manual
ACC2 StrongBox
Pedestal Assembly Instructions
®

Advertisement

loading

Related Manuals for Hunter ACC2

Summary of Contents for Hunter ACC2

  • Page 1 ACC2 StrongBox Pedestal Assembly Instructions ®...
  • Page 2 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Instructions for installing the Hunter ACC2 Controller into the StrongBox SB-16SS Stainless Steel Pedestal Kits Required Hunter StrongBox • Hunter P/N A2C1200SBKIT (12-station conventional • P/N “SB-16SS” (Stainless steel pedestal): If the StrongBox controller kit, includes facepack, inner panel and...
  • Page 3 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Unboxing the Hunter ACC2 inner chassis subassembly (ACC2 Decoder model shown)
  • Page 4 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Unboxing Bag Contents • Fig. 1: Bag of hardware and User Guides, • Fig. 5: Extended length RJ11 Reversed • Fig. 10: ACC2 Quick Start Guide (qty: 1), which includes the following: 6-Wire (qty: 1) Decoder version shown •...
  • Page 5 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Tools Required Assembly • 11 mm socket wrench Disassembling the Hunter ACC2 Step 1: Loosen the captive screws (qty: 3) using #2 Phillips head screwdriver (Fig. 1 & 2). inner chassis: Power supply assembly • 14 mm socket wrench...
  • Page 6 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Assembly Disassembling the Hunter ACC2 Step 1: Remove output module by sliding the Step 3: Remove the deck assembly by tilting slidelock from the locked to the unlocked up as shown and pulling out (Fig. 3).
  • Page 7 • Orient the StrongBox inner panel as shown with the ground stud at the bottom. chassis assembly to the StrongBox Note the three locations for installing the inner panel screws that attach the Hunter ACC2 inner chassis to the StrongBox inner panel. ○ ○ Attachment location Attachment location ○...
  • Page 8 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Assembly Assembling the Hunter ACC2 inner Step 1: Install the 8-32 X 1 screws (qty: 3) in the locations shown using #2 Phillips head chassis assembly to the StrongBox screwdriver (Fig. 1 & 2). inner panel •...
  • Page 9 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Assembly Assembling the Hunter inner chassis • Installation of the Hunter ACC2 inner chassis to the StrongBox inner panel assembly to the StrongBox inner panel...
  • Page 10 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Reassembly of Hunter Inner Chassis Assembly Assembly Reassembling the Hunter ACC2 inner Step 1: Install the deck assembly by inserting the lower hooks and tilting back (Fig. 1). chassis assembly: Deck assembly • Make sure both cables on the left side are (Decoder version shown) outside of the deck assembly.
  • Page 11 Installing the SmartPort adapter Note: If installing a Hunter supplied SmartPort adapter, use the following instructions. If not, skip to page 14. • Fig. 1: Hunter supplied SmartPort adapter • Fig. 2: StrongBox supplied SmartPort sheet metal bracket and hardware Fig. 1...
  • Page 12 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Optional Assembly Installing the SmartPort adapter Install the Hunter SmartPort Step 1: adapter onto the sheet metal bracket, as shown (Fig. 1). Fig. 1...
  • Page 13 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Optional Assembly Installing the SmartPort adapter • Fig. 1: Location for the SmartPort adapter Step 2: Make sure the small ribs on the connection SmartPort adapter connector face to the right when connecting with the mating Step 1: Using the side slot opening of the inner connector (Fig.
  • Page 14 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Assembly Power supply assembly should sit flush. Reassembling the Hunter ACC2 inner Step 1: Reconnect the two cables from the Tighten the captive screws (qty: 3) using #2 deck assembly (Fig. 1). chassis assembly: Power supply assembly Phillips head screwdriver (Fig.
  • Page 15 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Assembly Reassembling the Hunter ACC2 inner Step 1: Make sure the slidelock is in the UNLOCKED position (slide to the right). chassis assembly: Output module Install the output module into the deck (Decoder version shown) assembly (Fig.
  • Page 16 4 mounting screws support bracket to the inner panel Step 1: Locate support bracket as shown and install screws. Push up tight against the Hunter inner chassis and tighten screws using #2 Phillips head screwdriver (Fig. 2). Fig. 1 Fig. 2...
  • Page 17 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Assembly Disassembling the StrongBox pedestal Step 1: Open the StrongBox Pedestal top door and remove the front door (Fig. 1). Step 2: Remove the nuts and washers (qty: 4) using a 14 mm socket (Fig. 2 & 3).
  • Page 18 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Assembly Installing the inner panel assembly Step 1: Install through the front opening with the right side angled in first, as shown (Fig. 1). Step. 3: Hang the inner panel assembly on the four studs on the back wall. Reinstall the four...
  • Page 19 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Assembly Installing the facepack adapter panel Step 1: Remove the supplied screws (qty: 4) using #2 Phillips head screwdriver (Fig. 1 & 2). Step2: Install the facepack adapter panel (Fig. 3). ○ ○ ○ ○...
  • Page 20 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Assembly Installing the facepack adapter panel Step 1: Position the facepack adapter panel using the slots shown below (Fig. 1). Step 2: Reinstall the screws (qty: 4) using #2 Phillips head screwdriver (Fig. 2). ○...
  • Page 21 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Assembly Installing the facepack assembly Step 1: Loosen the screws for the facepack Step 3: Route the I/O cable assembly through assembly hold-down brackets (qty: 2) using the facepack adapter panel, as shown (Fig. 3).
  • Page 22 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Assembly Installing the facepack assembly Step. 1: Position the facepack Step 3: Make sure the panel door swings open assembly hold-down brackets up against the properly (Fig. 3). facepack assembly and tighten screws (qty: 2) using #2 Phillips head screwdriver (Fig.
  • Page 23 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Assembly Step 1: Install the I/O cable RJ connector into Step 3: Once dry, install the supplied cable tie Installing the facepack assembly the power supply assembly jack, as shown mount to side wall and install the I/O cable (Fig.
  • Page 24 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Optional Assembly Note: If you installed the Hunter SmartPort Installing the SmartPort adapter Step 2: Insert the SmartPort wires into the Adapter, then use the following instructions. cable tie mount, as shown (Fig. 2). If not, skip to page 25.
  • Page 25 ACC2 STRONGBOX PEDESTAL ASSEMBLY INSTRUCTIONS Assembly Assembling the final components Step 1: Reinstall the facepack adapter panel screws (qty: 2) using #2 Phillips head screwdriver (Fig. 1). Step 2: Reinstall the front pedestal door (Fig. 2). Step 3: Lower the top door (Fig. 3).
  • Page 26 1940 Diamond Street, San Marcos, CA 92078 USA hunterindustries.com StrongBox is a trademark of V.I.T. Products Inc. © 2021 Hunter Industries™. Hunter, the Hunter logo, and all other trademarks are property of Hunter Industries, RC-004-IG-US 3/21 registered in the U.S. and other countries.