ooma Telo Handset Quick Start Manual

Package Contents
TM
Ooma Telo Handset™ Cradle
Getting Started
You're just a few quick steps from getting up and dialing with your Ooma Telo Handset.
This handset is the perfect companion to the Ooma Telo™ — you'll be able to access all
Ooma features and unlock new functionality! Before you begin, please make sure your
Ooma Telo is installed and operating properly.
Step 1
Insert Battery
Remove the battery cover located on the back of the Ooma Telo Handset by sliding it away
from the center of the device. Insert the battery plug into the connector on the handset. Replace
Ooma Telo Handset
™
the battery cover by sliding it in the other direction.
Quick Start Guide
700-0111-100
Step 2
Charge the Handset
Connect the AC adapter cable to the charging
cradle and then plug the AC adapter into a
power outlet. Put the Ooma Telo Handset on the
charging cradle. When charging, you'll see the
blue light on the front of the cradle light up.
We recommend that you charge
!
the handset for at least 30 minutes
before proceeding to the next step.
The handset requires 10 hours to
fully charge.
AC Adapter
Battery
Step 3 Register the Handset
Find the 4-digit PIN number for your Ooma
Telo by logging into:
http://my.ooma.com/pin
Bring the handset next to the Ooma Telo. Set
the Ooma Telo in registration mode by pressing
and holding the key for 3 seconds. The
key will start flashing rapidly.
When prompted on the handset, enter the PIN
number found above and press the OK soft-
key. When the handset successfully registers, a
home screen will be displayed.
Each Ooma Telo supports up to four Ooma Telo
Handsets. This is in addition to any phones
plugged into the PHONE port of the device.
1
Display Basic Operation
Home screen
Placing and receiving calls
After registration, you'll see something like the
To place a call, press and dial the phone
following on the display:
number. You can also dial the number first and
then press .
To answer a call, press when the phone
rings.
Handset 1
You may end any call by pressing .
You have new VM
Speakerphone
Press to start a call in speakerphone mode
or you can press during a call to switch to
speakerphone mode. Press to go back to
using the earpiece.
Status indicators
The status indicators appear on the top row of
Volume adjustment
the display:
To adjust the ringer volume, press on the
navigation pad while you're not on an active
call.
Signal Strength Indicator
To adjust the call volume, press while
Signal bars show the connection
you're on an active call. This will adjust the
strength to the Ooma Telo
volume setting for both the earpiece and
Battery Indicator speakerphone.
Vertical bars show the battery level
charge or flash when the battery is Handset paging
charging
To locate your handset, press the key on
the Ooma Telo. If your handset is charged, it
Line Indicators
will emit a chiming sound. The handset will
Shows which lines are currently in
chime for 30 seconds.
use.
Ringer Off Indicator Press on the handset to stop paging.
Shows the ringer volume is turned
off.
2
Calling Features
Caller-ID Redial
When an incoming call rings your handset, Press to bring up a list of previously dialed
you'll see the caller-ID number associated with numbers. Press to select an entry and then
press to redial the number.
the caller on your handset display (if available).
International calls
If the number is associated with a contact,
you'll also see the name shown on the handset To place an international call, dial 0 1 1
display. followed by the country code and phone
number. Your prepaid balance will be
Note: For numbers not in your contact list,
announced before the call is connected.
you'll see the caller-ID name if you have Ooma
Premier.
Note: To make international calls and access
other premium services such as 411, you must
Contact list
charge-up your prepaid account at:
You can add phone numbers to the contact
my.ooma.com/prepaid.
list on your Ooma Telo Handset by logging into
my.ooma.com/contacts.
To place a call using your contact list, press
on the navigation pad to view a list of your
contacts. Press to select a contact and
then press to call.
Read about Ooma
Call-waiting
Premier features on
Switch to a second incoming call by pressing
. The current call will automatically be the backside
put on hold. Switch back to the first call by
pressing again.
Call log
Press on the navigation pad to view
recently received calls. Press to select an
entry. If the phone number is available, you can
press to return the call.
3
4