Hasbro Play-Doh Toy Time Race Game Instructions

MODELING COMPOUND
®
FOR TO PLAYERS
I
NSTRUCTIONS
Contents: • Gameboard •  Two-Ounce Cans of PLAY-DOH® Compound
•  Plastic Gears, Hubs and Bases • Recycle Stamper
•  Toy Molds (Mr. Potato Head , Chuck the Dump Truck
TM
• Spinner board, base and arrow • Gift Box • Recycle Box
Adult Assembly Required.
O
BJECT
Race your PLAY-DOH® toys through the Fun Factory toward the Gift Box at the end of
the Fun Factory Assembly Line. Have fun moving along the gears and turning them
round and round... but watch out for the Recycle Stamper! To win, be the rst to get
two toys into the Gift Box!
G S
AME ETUP
gift
box
toy
mold
spinner
This illustration shows a
-player game ready to play. Please
refer to it as you
assemble and set up your game.
A Y G
SSEMBLING OUR AME
Remove the game parts from their cardboard sheets and plastic wrappings. Dis-
card the waste. Carefully detach the spinner base, arrow, and toy molds from their
plastic runners. Discard the runners. If needed, use an emery board or sandpaper
to remove any excess plastic from the game parts.
S A
PINNER SSEMBLY
TM
AGES +
, My Little Pony and Can of PLAY-DOH®)
TM TM
recycle box
recycle
stamper
nish
line
toys on
start
P
ARTS
T M A
OY OLD SSEMBLY
Be sure to match
up the correct
halves of each
toy mold!
G & R B A
IFT ECYCLE OX SSEMBLY
Assemble the gift box as shown here. Then assemble the recycle box the same way.
Note: The recycle box has no lid.
2
slot
1
Fold along all
dotted lines.
GETTING READY TO PLAY
A G B
TTACH THE EARS TO THE OARD
Attach each of the four gears to the gameboard as shown here. Then line them up with their
outlines on the board.
Center a base under a Press a gear design-side up onto
gameboard hole with the the base peg, then snap it in. Make
peg facing up. sure the base peg is centered.
M Y T !
AKE OUR OYS
Choose a toy mold and any color of PLAY-DOH® compound. Then make each toy as shown
here. Place any extra compound back in the can and close the lid securely. Start the game with
two toys on the gameboard.
Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Place a small wad of PLAY-DOH® Press the mold
compound in the open mold. together rmly.
Extra toys: You can have any number of toys on the board at one time, so
make as many as you want! You'll also need extras to replace any toys that get
recycled.
tab
4
3
Fold in the side tabs, then fold up
the bottom and lock in.
Then press and snap a hub
onto the gear.
Tap out your toy. Remove any excess Tap out your toy. Remove any excess Tap out your toy. Remove any excess Tap out your toy. Remove any excess Tap out your toy. Remove any excess Tap out your toy. Remove any excess Tap out your toy. Remove any excess Tap out your toy. Remove any excess Tap out your toy. Remove any excess Tap out your toy. Remove any excess Tap out your toy. Remove any excess Tap out your toy. Remove any excess Tap out your toy. Remove any excess Tap out your toy. Remove any excess Tap out your toy. Remove any excess
compound and replace in the can.