Sony Cyber-shot DSC-T7 Operating Instructions

2-591-811-11 (1)
Digital Still Camera
Read This First
Read This First
Operating Instructions
Before operating the unit, please read this manual and "User's Guide/Troubleshooting" (separate
volume) thoroughly, and retain it for future reference.
DSC-T7
Refer to "User's Guide/Troubleshooting"
(separate volume)
Explains advanced techniques and what to do if you experience trouble with
your camera.
Printed on 100% recycled paper using VOC
(Volatile Organic Compound)-free vegetable
© 2005 Sony Corporation Printed in Japan
oil based ink.
2591811110
Checking the accessories supplied
• Battery charger BC-CS3 (1) • A/V cable (1) • "Memory Stick Duo"
(32 MB) (1)
• Rechargeable battery pack • Neck strap (1) • Memory Stick Duo Adaptor
NP-FE1 (1) (1)
• Battery case (1) • Interface Adaptor (1) • CD-ROM (Cyber-shot
application software) (1)
• Operating instructions for
digital still camera "Read
This First" (this manual) (1)
• Operating instructions
• USB cable (1) • Stand (1)
"User's Guide/
Troubleshooting" (1)
Notes before use
• Charge the supplied NP-FE1 battery pack before using the camera for the first time.
• The camera is a precision instrument. Be careful not to bump the lens or the LCD screen, and not to
apply force to it. Attach the strap to prevent the camera from damage by being dropped, etc.
Hook Avoid letting the stopper on the neck strap (for
length adjustment) hit or rub against the LCD
screen. This may damage the camera.
Additional information on this product and answers to frequently asked questions can be
found at our Customer Support Website.
http://www.sony.net/
Downloaded from: https://www.usersmanualguide.com/
1 1
Prepare the battery pack
1 2
Insert the battery pack. Lift out the inlet plug and
connect to the wall outlet
Push the back part of the battery pack
(wall socket).
gently until it clicks into place.
Battery charger
CHARGE lamp
Plug Light on: Charging
Light off: Completed (Practical charge)
If you continue charging the battery pack for about
one more hour (until it is fully charged), the
charge will last slightly longer.
• Connect the battery charger to an easily accessible wall outlet (wall socket) close by.
• Even if the CHARGE lamp is not lit, the battery charger is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet (wall socket). If some trouble occurs while using the
battery charger, immediately shut off the power by disconnecting the plug from the wall outlet (wall socket).
• When charging is finished, disconnect the battery charger from the wall outlet (wall socket), and remove the
battery pack from the battery charger.
"InfoLITHIUM" battery pack Full charging time (Practical charging time)
NP-FE1 (supplied) Approx. 170 min. (Approx. 110 min.)
• Time required to charge fully depleted battery pack at a temperature of 25°C (77°F). Charging may take
longer under certain circumstances or conditions.
3
Insert the charged battery pack.
Battery eject
lever
Open the cover. Insert the battery pack while
Close the cover.
pressing the battery eject lever
with the tip of the battery.
Using the AC Adaptor
You can connect the camera using the AC-LS5/AC-LS5K AC Adaptor (not supplied). t
"User's Guide/Troubleshooting" (page 15). Refer to the operating instructions supplied with the
AC Adaptor.
To check the remaining battery time
Press (power) to turn on and check the time on the LCD screen.
• It takes about one minute until the correct battery remaining
Remaining indicator
time appears.
60min
• The displayed time remaining may not be correct under certain
circumstances.
Remaining time
To remove the battery pack
Open the battery cover and slide the battery eject lever in the direction of the arrow. Place your
finger on the flange and push the battery pack out. To avoid dropping the battery pack, do not
hold the camera with the battery slot facing down when the battery eject lever is out.
Battery eject lever
To use your camera abroad — Power sources
You can use your camera, the supplied battery charger, and the AC-LS5/AC-LS5K AC Adaptor
(not supplied) in any country or region where the power supply is within 100 V to 240 V AC, 50/
60 Hz. Use a commercially available AC plug adaptor [a], if necessary, depending on the design
of the wall outlet (wall socket) [b].
• Do not use an electronic transformer (travel converter), as
this may cause a malfunction.
BC-CS3
2 2
Turn the camera on/set the clock
1 2
Select . Slide the lens cover or
press (power).
Lighting
Clock Set
2005 / / 12 : 00
1 1
3
Set the clock with the control
button.
1
Select the date display format with v/V, then press
z.
Clock Set
2005 / 1 / 1 12 : 00
AM
2
Select each item with b/B and set the numeric value
with v/V, then press z.
Clock Set
2005 / 1 / 1 12 : 00
AM
3
Select [OK] with B, then press z.
Clock Set
2005 / 1 / 1 10 : 30
AM
• To cancel, select [Cancel] and press z.
To change the date and time
Select [Clock Set] in the (Setup) screen and perform the procedure in step 3 above.
t "User's Guide/Troubleshooting" (page 53)
On the clock display
• If you selected [D/M/Y] in step 3-1, set the time on a 24-hour cycle.
• Midnight is indicated as 12:00 AM, and noon as 12:00 PM.
When turning on the power
• Unless you set the clock, the Clock Set screen appears each time the camera is turned on.
• The following screen appears when the camera is turned on for the second time or afterwards.
60min
When opening the lens cover
• If you open the lens cover too quickly, the camera might not turn on. If this happens,
close the cover and then open it again more slowly.
• When opening the lens cover, be careful not to touch the lens.
To turn off the power
Slide the lens cover or press again.
• If the camera is running on battery power and you do not operate the camera for a period of time, the camera
turns off automatically to prevent wearing down the battery (Auto power-off function).
Changing the language setting
You can change the screen display to show messages in a specified language. To change the
language setting, press MENU to display the menu screen. Select (Setup) with the control
A (Setup1), and select the desired language. t "User's
button, then, select [ Language] in
1
Guide/Troubleshooting" (page 51)
3 3
Insert a "Memory Stick Duo"
Terminal side
Y/M/D
M/D/Y
D/M/Y
OK
AM
Cancel Insert the "Memory Stick Duo" all
the way in until it clicks.
4
4
Select the image size for use
1 2
Select a mode. Press
Y/M/D
M/D/Y
Still image:
D/M/Y
3
OK Select the size with v/V.
Cancel
Select .
Movie:
Y/M/D • The screen above is for still images.
Select .
M/D/Y
For movies, select [640(Fine)] ("Memory Stick PRO
D/M/Y
Duo" only), [640(Standard)] or [160].
OK
Cancel
4
Press
complete the setting.
Y/M/D
M/D/Y
D/M/Y
OK
Cancel
button
On still image sizes
For details on the image size t "User's Guide/Troubleshooting" (page 13)
Image size Guidelines
5M (2592×1944) For printing high density images in A4 or
A5 size
(Default setting)
3:2* (2592×1728)
3M (2048×1536)
1M (1280×960) For printing in postcard size
VGA(E-Mail) For recording a larger number of images
(640×480) For attaching images to e-mail or creating
home pages
* Images are recorded in the same 3:2 aspect ratio as photograph printing paper or postcards etc.
On recordable number of still images and recordable time of movies
Recordable number of still images and recordable time of movies vary depending on the image
size selected.
For details on recordable number or time t "User's Guide/Troubleshooting" (page 22)
Still images
Maximum recordable image Maximum recordable time
• Number of recordable images and time can differ according to shooting conditions.
To remove a "Memory Stick Duo"
Open the cover, then push the "Memory Stick Duo" in once.
• If the access lamp is lit, never remove the "Memory Stick Duo" or
turn off the power. The data may be corrupted.
Access lamp
continued on the reverse
(Image Size).
5M
3:2
3M
1M
1M
VGA(E-Mail)
Image Size
(Image Size) to
No. of images Printing
Less Fine
More Rough
Movies