Page 1
TO24-JD0 TO24-JD1 ORV3 Storage Node 3 x Broadcom SAS4X32 SAS expanders, single-path (TO24-JD0) 6 x Broadcom SAS4X32 SAS expanders, dual-path (TO24-JD1) User Manual Rev. 1.0...
Page 2
For GIGABYTE distributors and resellers, additional sales & marketing materials are available from our reseller portal: http://reseller.b2b.gigabyte.com For further technical assistance, please contact your GIGABYTE representative or visit https://esupport.gigabyte.com/ to create a new support ticket For any general sales or marketing enquiries, you may also message GIGABYTE server directly by email: server.grp@gigabyte.com...
Page 3
Conventions The following conventions are used in this user's guide: NOTE! Pieces of additional information related to the current topic. CAUTION! Precautionary measures to avoid possible hardware or software problems. WARNING! Alerts to any damage that might result from doing or not doing specific actions.
Page 4
Server Warnings and Cautions Before installing a server, be sure that you understand the following warnings and cautions. WARNING! To reduce the risk of electric shock or damage to the equipment: • Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
Page 5
Electrostatic Discharge (ESD) CAUTION! ESD CAN DAMAGE DRIVES, BOARDS, AND OTHER PARTS. WE RECOMMEND THAT YOU PERFORM ALL PROCEDURES AT AN ESD WORKSTATION. IF ONE IS NOT AVAILABLE, PROVIDE SOME ESD PROTECTION BY WEARING AN ANTI-STATIC WRIST STRAP AT- TACHED TO CHASSIS GROUND -- ANY UNPAINTED METAL SURFACE -- ON YOUR SERVER WHEN HANDLING PARTS.
Page 6
Installing or removing jumpers: A jumper is a small plastic encased conductor that slips over two jumper pins. Some jumpers have a small tab on top that can be gripped with fin-gertips or with a pair of fine needle nosed pliers. If the jumpers do not have such a tab, take care when us- ing needle nosed pliers to remove or install a jumper;...
Table of Contents Chapter 1 JBOD Hardware .....................8 Installation Precautions ..................8 Product Specifications ..................9 Chapter 2 JBOD System Appearance ................10 Front View ...................... 10 Top View ......................11 Rear View ....................... 11 Front Panel LED and Buttons ................ 12 Hard Disk Drive LEDs ..................
Chapter 1 JBOD Hardware Installation Precautions The motherboard/system contain numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the service guide and follow these procedures: • Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or warranty sticker provided by your dealer.
Supported Supported RAID Depends on SAS Card SAS Expander 3 x Broadcom SAS4X32 SAS expanders, single-path (TO24-JD0) (TO24-JD1) 6 x Broadcom SAS4X32 SAS expanders, dual-path Front I/O 8 x Mini-SAS HD ports 1 x Power button ...
Chapter 2 JBOD System Appearance Front View TO24-JD0 TO24-JD1 Description Front Panel LEDs and Buttons Server Management LAN Port miniSAS Hard Disk Drive Connectors A1 / A2 / A3 / A4 (from left to right) miniSAS Hard Disk Drive Connectors B1 / B2 / B3 /B4 (from left to right/TO24-JD1 Only) Please go to Front Panel LED and Buttons on page 12 for detail description of function LEDs.
Front Panel LED and Buttons No. Name Color Status Description Audio Jack For management console Reset Button Press this button to reset the system. Green Indicates the system is powered on and .in a normal state Power button with LED Green Blink Voltage event has occurred...
Hard Disk Drive LEDs HDD2 HDD3 LED3 LED4 HDD_LED4 HDD_LED3 LED1 LED2 HDD_LED2 HDD_LED1 HDD0 HDD1 LED 0~3 HDD Present Color No HDD (No Access) Green HDD LED 0~3 Color Locate Fail HDD Access Green Blink Amber System Appearance - 13 -...
Front System LAN LEDs Name Color Status Description Amber 1Gbps data rate Speed Green 100Mbps data rate Link between system and network or no access Green Link/Act Blinking Data transmissionor receiving is occuring No data transmission or receiving is occuring System Appearance - 14 -...
Chapter 3 JBOD System Hardware Installation Pre-installation Instructions Computer components and electronic circuit boards can be damaged by discharges of static electricity. Working on computers that are still connected to a power supply can be extremely dangerous. Follow the simple guidelines below to avoid damage to your computer or injury to yourself.
Removing the JBOD from the Rack Follow these instructions to remove the JBOD from the rack: Press the release latches outward while simultaneously pulling the handle for the JBOD. Pull the JBOD out of the cabinet. To install the JBOD, push the JBOD back into the cabinet. System Hardware Installation - 16 -...
Removing and Installing the HDD Tray Follow these instructions to remove the HDD Tray: Press the release latches inward while simultaneously pulling the handle for the HDD tray. To install the HDD tray, push the HDD tray back into the JBOD until it clicks. System Hardware Installation - 17 -...
Installing the Hard Disk Drive Read the following guidelines before you begin to install the Hard disk drive: • Take note of the drive tray orientation before sliding it out. • The tray will not fit back into the bay if inserted incorrectly. •...
Replacing the Fan Assembly Follow these instructions to replace the fan assembly: Press the release latches on the bottom-left and top-right sides of the fan assembly inwards while pulling the fan out of its compartment. To install the replacement fan assembly, push the assembly into the compartment. System Hardware Installation - 19 -...