Panasonic HDC-SD100P Service Manual page 14

Service Manual
Diagrams and Replacement
Parts List
High Definition Video Camera
Model No.
HDC-SD100P HDC-SD100EG
HDC-SD100PC HDC-SD100EP
HDC-SD100PL HDC-SD100GC
HDC-SD100E HDC-SD100GK
HDC-SD100EB HDC-SD100GN
HDC-SD100EE HDC-SD100GT
HDC-SD100EF HDC-SD100SG
Vol. 2
Colour
(K)...........Black Type
Table of contents
S1. About Indication of The Schematic Diagram ............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Voltage Chart ........................................................................... S-2
S2.1. Main P.C.B. ........................................................................... S-2
S2.2. Sub P.C.B. ............................................................................. S-2
S3. Block Diagram .......................................................................... S-3
S3.1. System Control Block Diagram ............................................. S-3
S3.2. Video/Audio Signal Process Block Diagram ......................... S-4
S3.2.1. Video/Audio Signal Process Block Diagram (1) ................. S-4
S3.2.2. Video/Audio Signal Process Block Diagram (2) ................. S-5
S3.3. Camera Block Diagram ......................................................... S-6
S3.4. Lens Drive Block Diagram..................................................... S-7
S3.5. Power Block Diagram............................................................ S-8
S4. Schematic Diagram .................................................................. S-9
S4.1. Interconnection Diagram ....................................................... S-9
S4.2. Main CN Schematic Diagram .............................................. S-10
S4.3. Video Schematic Diagram ................................................... S-14
VM0808038CE
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice
COMPONENTS IDENTIFIED WITH THE MARK
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as "
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
S4.4. Process Schematic Diagram ............................................... S-18
S4.5. Sensor Schematic Diagram ................................................ S-22
S4.6. Lens Drive Schematic Diagram........................................... S-26
S4.7. AVIO Schematic Diagram .................................................... S-30
S4.8. Syscon Schematic Diagram ................................................ S-32
S4.9. V DAC Schematic Diagram ................................................. S-36
S4.10. HDMI Schematic Diagram................................................. S-37
S4.11. USB Host Schematic Diagram .......................................... S-38
S4.12. G Sensor Schematic Diagram........................................... S-39
S4.13. Power B Schematic Diagram ............................................ S-40
S4.14. Power A Schematic Diagram............................................. S-42
S4.15. Sub CN Schematic Diagram ............................................. S-46
S4.16. RTC Schematic Diagram .................................................. S-50
S4.17. SD Holder Schematic Diagram ........................................ S-51
S5. Print Circuit Board .................................................................. S-52
S5.1. Main P.C.B. ......................................................................... S-52
S5.1.1. Main P.C.B. (Component Side) ........................................ S-52
S5.1.2. Main P.C.B. (Foil Side) ..................................................... S-56
S5.1.3. Main P.C.B. Address Information ..................................... S-60
S-1
" mark.
Circuit name being connected.
This signal is connected
OFTR FEP
to the FEP schematic diagram.
Name of Signal
S5.2. Sub P.C.B. ........................................................................... S-62
S5.2.1. Sub P.C.B. (Component Side) .......................................... S-62
S5.2.2. Sub P.C.B. (Foil Side) ...................................................... S-63
S5.2.3. Sub P.C.B. Address Information ....................................... S-64
S6. Replacement Parts List .......................................................... S-65
HAVE THE SPECIAL CHARACTERISTICS