General - Sony XAV-AX5600 Service Manual

XAV-AX5600
This section is extracted from
operating instruction.
Connection/Installation
Cautions
• Do not install this unit in a car that has no ACC
position. The display of the unit does not turn o
even after turning the ignition o , and this causes
battery drain.
• Run all ground (earth) leads to a common
ground (earth) point.
• Do not get the leads trapped under a screw or
caught in moving parts (e.g., seat railing).
• Before making connections, turn the car ignition
o to avoid short circuits.
• Connect the yellow and red power supply leads
only after all other leads have been connected.
• Be sure to insulate any loose unconnected leads
with electrical tape for safety.
• Choose the installation location carefully so that
the unit will not interfere with normal driving
operations.
• Avoid installing the unit in areas subject to dust,
dirt, excessive vibration, or high temperature, such
as in direct sunlight or near heater ducts.
• Use only the supplied mounting hardware for a
safe and secure installation.
Note on the power supply lead (yellow)
When connecting this unit in combination with other stereo
components, the amperage rating of the car circuit to which
the unit is connected must be higher than the sum of each
component's fuse amperage rating.
Note on installing in cars with a start-stop system
The unit may restart when starting the engine from start-
stop. In this case, turn o the start-stop system of your car.
Note on installing in cars with electric parking brake
system
For cars with electric parking brakes, some related functions
(such as video blocking function) may not work properly.
Mounting angle adjustment
Adjust the mounting angle to less than 30°.
*1 Not supplied
*2 Speaker impedance: 4 to 8 × 4
*3 RCA pin cord (not supplied)
*4 Depending on the type of car, use an adaptor for a wired
remote control (not supplied).
For details on using the wired remote control, see "Using
the wired remote control".
*5 Depending on the type of car, use an adaptor (not
supplied) if the antenna (aerial) connector does not fit.
*6 Whether in use or not, route the microphone input cord
so it does not interfere with driving operations. Secure
the cord with a clamp, etc., if it is installed around your
feet.
*7 For details on installing the microphone, see "Installing
the microphone".
*8 For more information on how to install the SiriusXM
Connect Vehicle Tuner, consult the installation guide
included with the tuner.
*9
*10 When using the steering wheel remote control, use the
connection cable RC-SR1 as necessary.
*11 Use the USB extension cable or a commercially
available one.
*12 Use the cable tie or a commercially available one.
*13 For details on using an HDMI device, see "Using an HDMI
device".
*14 When updating the firmware, insert the USB device to
USB port 1, then switch to USB port 2 following the on-
screen guidance.
19
SECTION 2

GENERAL

Connection
• To prevent short circuits, insulate leads with a cover or tape.
• Note that the unit may be damaged if it is connected incorrectly or by short circuits at the leads.
White
White/black striped
Gray
Gray/black striped
Green
Green/black striped
Purple
Purple/black striped
Black
Yellow
Red
Blue/white striped
Orange/white striped
Light green
Purple/white striped
Making connections
To a common ground (earth) point
First connect the black ground (earth) lead then
connect the yellow and red power supply leads.
To the +12 V power terminal which is
energized at all times
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
To the +12 V power terminal which is
energized when the ignition switch is set to
the accessory position
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
To the power antenna (aerial) control lead or
the power supply lead of the antenna (aerial)
booster
It is not necessary to connect this lead if there is
no power antenna (aerial) or antenna (aerial)
booster, or with a manually-operated telescopic
antenna (aerial).
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers and a
power antenna (aerial). Connecting any other
system may damage the unit.
Note
It will take about 10 seconds to shut down the output of
REM OUT after the unit is turned o .
FUSE 10A
To a car's illumination signal
Be sure to first connect the black ground (earth)
lead to a common ground (earth) point.
To the parking brake switch lead
The mounting position of the parking brake
switch lead depends on your car.
Be sure to connect the parking brake lead (light
green) of the power supply leads
parking brake switch lead.
H n a d b a r e k y t e p
To the +12 V power terminal of the car's rear
lamp lead (only when connecting the rear
view camera)
Sony CONFIDENTIAL
For Authorized Servicer
Subwoofer* 1
*
3
* 3
* 3
Power amplifier*
1
* Rear view
3
camera*
1
* 6 * 7
from a wired remote control (not
supplied)
*4*10
* 9 * 12
USB device (for audio
playback only)* 1 * 14
*
11
Smartphone, USB device
(for audio/video
playback)* *
1 14
* *
9 12
Satellite radio tuner
(SiriusXM)* *
1 8
Front speaker* *
1 2
Rear speaker* 1 * 2
For details, see "Making
connections".
from an HDMI device* *
1 13
from a car antenna (aerial)* *
1 5
to the
Parking brake switch lead
o F t o b a r e k y t e p
SYS SET