Crest Audio MFP44FM Quick Start Manual

Step 4: Full Motion Adjustment & Maintenance
1. To change the tilt angle of your display, have one person hold the display firmly in place while another person loosens the
tilt adjustment nut. Once loosened, move your display to the desired position, and then re-tighten the nut (see Figure.8).
Do not release the display until the nut is fully tightened.
2. Swivel adjustments can be made by moving the display to the desired position. Be careful that fingers or cables do not get
pinched when moving the mount.
400mm
300mm
200mm
100mm
+4°
-8°
+ - 2°
Figure 8
WARNING: Do not loosen too much as the Wall Mount may fall apart.
Check your TV Wall Mount is secure and safe to use at regular intervals (at least every three months).
5 YEAR WARRANTY
Olbertz Holdings Pty Ltd ACN 010 003 933 trading as The Crest Company of 165 South Pine Road, Brendale, Queensland, 4500, Ph: 1800 812 261,
www.crest.com.au, warrants that if this Crest product purchased by you from The Crest Company or a retail outlet is found by The Crest Company to be
defective in workmanship or materials within 5 years of the date of purchase, The Crest Company will (at its election) either repair that product, replace the
product, supply an equivalent product or pay the costs of repairing or replacing the product or acquiring an equivalent product.
This limited warranty will not extend to or cover any expenses associated with removing, demounting the original product or installing the repaired, replaced
or equivalent product or all or any of its components, you must bear these expenses. It also does not cover damage or loss resulting from intentional or
unintentional misuse of, tampering with, alterations to or incorrect installation of this product or use of this product for purposes other than that for which it
is designed or in a manner inconsistent with the product's instructions. This limited warranty also does not apply to damage or loss resulting from fair wear
and tear or events beyond The Crest Company control including but not limited to natural disasters.
In order to claim under this warranty, you must contact The Crest Company and return to The Crest Company (via our nominated reply paid address) the
product and its components and proof of purchase (including the date and location of purchase) so that The Crest Company can verify the defect and
your purchase.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major
failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure. The benefits given by this warranty are in addition to other rights and
remedies which you may have under a law in relation to the goods or services to which the warranty relates.
75mm
180°
180°
50-400mm
Proudly brought to you by:
PO Box 5658 Brendale
QLD Australia 4500
Customer Support
1800 812 261
www.crest.com.au
AUSTRALIAN OWNED
MFP44FM
TV Wall Mount
Full Motion
This TV Wall Mount allows you to move
your TV at all angles and extends out
up to 40cm from your wall
Compatible TV Size
This TV Wall Mount fits 20-55"
20-55"
(50-140cm) TV Screens
Maximum Mounting Pattern
This TV Wall Mount has a mounting
hole pattern up to 400x400mm (WxH)
400x400
mm
Maximum TV Weight
HOLDS
This TV Wall Mount supports TVs
40
kg
weighing up to 40kg
Hardware Kit Contents
ITEM DESCRIPTION
A M6 x 50mm Screw
B 10 x 50mm Anchor
C M6 x 12mm Bolt
D M6 Locknut
E M4 x 25mm Bolt
F M6 x 25mm Bolt
G M8 x 30mm Bolt
H M8 x 45mm Bolt
I M6 Washer
SAFETY FIRST
1. Installation of this TV Wall Mount will be easier with two people.
2. Some images in this guide may vary slightly from the actual
components supplied.
3. Ensure this instruction manual is completely read and
understood before attempting installation.
4. This TV Wall Mount MUST NOT be installed solely in
plasterboard, fibre cement and similar surfaces.
5. This TV Wall Mount MUST be installed in sound supporting
structures such as those made of timber, steel or masonry
using appropriate fasteners.
6. The supporting structure must be capable of sustaining
the combined weight of the TV Wall Mount and the display
otherwise the structure must be reinforced.
7. The fasteners supplied in this hardware pack allow for fixing
into timber and masonry only. If installing into a supporting
structure made of steel, appropriate fasteners must be used
and sourced from an appropriate supplier.
8. Use appropriate tools and safety equipment and ensure
adequate ventilation during installation.
9. If uncertain about any aspect of installation, contact
The Crest Company or an installation professional.
10. Please retain these instructions for future reference.
QTY ITEM DESCRIPTION
J
M8 Washer
4
K
Spacer
4
4 L Wrench
4 M Wall Plate
4
4 N Display Plate
4 O Display Plate Adaptors
4
8
QTY
4
8
1
1
1
4