Page 1
PSS u2 ES 4DOD 0.5A Control system PSS u2 Remote I/O system PSS u2 Operating Manual-1003613-EN-03...
Page 2
We do assure you that all persons are regarded without discrim- ination and on an equal basis. All rights to this documentation are reserved by Pilz GmbH & Co. KG. Copies may be made for the user's internal purposes. Suggestions and comments for improving this documenta- tion will be gratefully received.
This operating manual explains the function and operation, describes the installation and provides guidelines on how to connect the product. This documentation is valid for the product PSS u2 ES 4DOD 0.5A hardware version 01 or higher. It is valid until new documentation is published.
Page 5
Introduction INFORMATION This gives advice on applications and provides information on special fea- tures. Operating Manual PSS u2 ES 4DOD 0.5A 1003613-EN-03...
Details of the terminal blocks that can be used are available under "Intended Use". Module features Application of the product PSS u2 ES 4DOD 0.5A: Electronic module with digital outputs and expanded diagnostics for standard applications The product has the following features: 4 Digital outputs –...
Use of the module outside the areas described in this manual, Any use of the module that is not in accordance with the technical details. The module PSS u2 ES 4DOD 0.5A may be used in conjunction with the following terminal block:...
Any type of modification has been made (e.g. exchanging components on the PCB boards, soldering work etc.). 3.3.3 Disposal When decommissioning, please comply with local regulations regarding the disposal of electronic devices (e.g. Electrical and Electronic Equipment Act). Operating Manual PSS u2 ES 4DOD 0.5A 1003613-EN-03...
The value that is to be used as the substitute value can be configured. Substitute values may be: Output switched off (default value) Output switched on Last valid value Operating Manual PSS u2 ES 4DOD 0.5A 1003613-EN-03...
– The module switches off the voltage at the digital outputs. Standby mode – All module functions are inactive. – The LEDs for displaying the module and terminal status are switched off. Operating Manual PSS u2 ES 4DOD 0.5A | 10 1003613-EN-03...
1: The signal in the PIO corresponds to the Bit 1 Valid bit of output O1 output signal Bit 2 Valid bit of output O2 Bit 3 Valid bit of output O3 Bit 4-7 None Constant "0" Operating Manual PSS u2 ES 4DOD 0.5A | 11 1003613-EN-03...
6.1.1 Dimensions The dimensions include the backplane, electronic module and terminal block. 12,5 51,1 111,1 Fig.: Dimensions in mm, including backplane, electronic module and terminal block Operating Manual PSS u2 ES 4DOD 0.5A | 12 1003613-EN-03...
Unforeseeable error reactions may be triggered if modules are inserted and removed under load. 6.2.1 Inserting an electronic module 1. Insert the electronic module into the suspen- sion lug on the back- plane. Operating Manual PSS u2 ES 4DOD 0.5A | 13 1003613-EN-03...
Page 14
3. Insert the terminal block into the suspen- sion lug on the module. 4. Swivel the terminal block upwards until you hear it click into place. Operating Manual PSS u2 ES 4DOD 0.5A | 14 1003613-EN-03...
2. Press the unlocking mechanism that is shown by the arrow and pull off the electronic module upwards. Operating Manual PSS u2 ES 4DOD 0.5A | 15 1003613-EN-03...
– Restart of the head module. After a restart, the system behaves as after a warm reset using a reset pushbutton (see operating manual of the head module, chapter “Reset pusbutton", section "Carrying out a warm reset (restart)"). Operating Manual PSS u2 ES 4DOD 0.5A | 16 1003613-EN-03...
The module status display See module's dia- and the terminal status display gnostic log on the relevant output flash synchronously Short circuit/overload/under- voltage Temperature warning: Too See module's dia- warm (1) gnostic log Operating Manual PSS u2 ES 4DOD 0.5A | 18 1003613-EN-03...
Page 19
After the "too hot" message has been received, if the temperature drops back below the "too warm" threshold value, the module will switch to an error-free state. Legend LED on LED flashes LED flashes briefly LED off Operating Manual PSS u2 ES 4DOD 0.5A | 19 1003613-EN-03...
Ambient temperature In accordance with the standard EN 60068-2-14 Temperature range 0 - 60 °C Storage temperature In accordance with the standard EN 60068-2-1/-2 Temperature range -40 - 70 °C Operating Manual PSS u2 ES 4DOD 0.5A | 20 1003613-EN-03...
Page 21
Mechanical data Material Housing Mounting type plug-in Dimensions Height 110,8 mm Width 12,5 mm Depth 72,5 mm Weight 33 g Where standards are undated, the 2015-04 latest editions shall apply. Operating Manual PSS u2 ES 4DOD 0.5A | 21 1003613-EN-03...
61 x 11.5 mm, scope of supply: 10 pieces Coding elements Product type Features Order no. PSS u2 A CE E Coding elements for electronic modules, 328860 (10 pcs.) scope of supply: 10 pieces Operating Manual PSS u2 ES 4DOD 0.5A | 22 1003613-EN-03...
Page 23
Order reference Backplanes Product type Features Order no. PSS u2 B 1 Backplane, 1 slot 328811 PSS u2 B 4 Backplane, 4 slots 328810 Operating Manual PSS u2 ES 4DOD 0.5A | 23 1003613-EN-03...
Page 24
We are represented internationally. Please refer to our homepage www.pilz.com for further details or contact our headquarters. Headquarters: Pilz GmbH & Co. KG, Felix-Wankel-Straße 2, 73760 Ostfildern, Germany Telephone: +49 711 3409-0, Telefax: +49 711 3409-133, E-Mail: info@pilz.com, Internet: www.pilz.com...