Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Agilent Technologies N4972A
Summary of Contents for Agilent Technologies N4972A
- Page 1 Agilent N4972A Clock Synthesizer 16 GHz Getting Started Guide...
- Page 2 Agilent Technologies, Inc. as not correctly performed or adhered to, including but not limited to the implied governed by United States and international...
- Page 3 Environment Conditions operator may be used as a disconnecting Agilent Technologies Inc. assumes no device. liability for the customer's failure to comply This instrument is intended for indoor use in with these requirements.
- Page 4 Symbols on Instruments The Korean Certification (KC) mark is required for Indicates warning or caution. If you see this This mark indicates compliance with the Canadian products that are subject to legally compulsory symbol on a product, you must refer to the EMC regulations.
- Page 5 Environmental Information This product complies with the WEEE Directive (2002/96/EC) marketing requirements. The affixed label indicates that you must not discard this electrical/electronic product in domestic household waste. Product category: With reference to the equipment types in the WEEE Directive Annexure I, this product is classed as a “Monitoring and Control instrumentation”...
-
Page 7: Table Of Contents
Support ......................10 General Specifications .................. 10 Safety and Regulatory ................... 12 Unpacking ....................... 12 Important Notes ..................... 13 Installation ...................... 13 Connector Care ....................14 Returning the N4972A to Agilent Technologies ........15 Clock Synthesizer 16 GHz Getting Started Guide... - Page 8 Contents Clock Synthesizer 16 GHz Getting Started Guide...
-
Page 9: Getting Started
N4972A. The N4972A is shipped in a protective box with all the accessories required for operation. The shipping box contains: N4972A-CJ0 or N4972A-CJ1 (SCS16000 or SCS16000J) clock •... -
Page 10: Support
• SMA male to SMA male cable (2) • o Connect one cable from the Jitter output of the N4972A to the pattern generator clock input (or Ref CLK input of N4965A-CTR (PCB12500)) o Connect the other cable from the N4972A Delay output to the... - Page 11 Getting Started Parameter Specification Operating temperature +10°C to +40°C Storage temperature -40°C to +70°C Voltage 100 to 240 VAC ±10% autoranging Frequency 50/ 60 Hz Power 145 Watts MAX Current 1.8A RMS MAX Fuse 250 V 2A 5x20 mm (p/n 12260-002) Always replace instrument fuse with one of the same type and rating.
-
Page 12: Safety And Regulatory
Getting Started 1.4 Safety and Regulatory This product has been designed and tested in accordance with accepted industry standards, and has been supplied in a safe condition. The documentation contains information and warnings that must be followed by the user to ensure safe operation and to maintain the product in a safe condition. -
Page 13: Important Notes
SMA cable to connect the jitter clock output on the N4972A to the Clock In on the N4965A-CTR or N4971A. 4. If the N4972A is being used as a clock source for the N4962A (TG1B1- A) serial BERT, two clock connectors are needed. Connect the N4972A Jitter Clock output on the N4962A (TG1B1-A) TX CKI on the rear panel. -
Page 14: Connector Care
(jittered) clock output at the nominal default power on settings. 7. If the N4972A is being used to clock a N4962A, then the second output must also be enabled to clock the error detector: a. Return to the main menu by pressing Back (top soft key). -
Page 15: Returning The N4972A To Agilent Technologies
6. Make sure no particles or residue remains. 7. Inspect connector for damage. 1.9 Returning the N4972A to Agilent Technologies If the N4972A fails system verification and you cannot correct the problem, return N4972A to Agilent Technologies for repair following the steps shown below. - Page 16 © Copyright Agilent Technologies 2012 First edition, August 2012 Printed in Germany...