Page 1
1000 Internet Server ™ i.LON Starter Kit Version 1 078-0185-01A...
Page 2
Echelon, LON, LONWORKS, LonTalk, LonBuilder, LonManager, Neuron, 3120, 3150, LONMARK, NodeBuilder, and the Echelon logo are trademarks of Echelon Corporation registered in the United States and other countries. LonMaker and i.LON are trademarks of Echelon Corporation. No part of this publication may be reproduced,...
Contents 1 Introduction Contents of the i.LON 1000 Internet Server Starter Kit PC Requirements Software Installation Getting More Information and Technical Support Introduction to the i.LON 1000Internet Server 2 Hardware and Software Installation Hardware Installation Hardware Step-by-Step Installation Software Step by Step Installation 3 Working with Web Pages Transferring Web Pages to the i.LON 1000 using FTP...
Introduction Welcome to the i.LON 1000 Internet Server Starter Kit. This ® kit builds upon the Model 37400 L System Starter Kit ORKS by supplying you with everything you need to add web access to your control system. i.LON 1000 Internet Server Starter Kit...
System Starter Kit document. Once the examples described below ORKS are completed and you understand the basic principles of web-based monitoring and control, you can use the i.LON 1000 Internet Server to add a web interface to any network! ORKS...
Place the files in a convenient location. Getting More Information and Technical Support This document provides information on using the i.LON 1000 Internet Server to add web pages to the examples described in the Getting Started with the L...
Internet access to the everyday devices in your world – lights, appliances, switches, thermostats, motors, meters, and valves. The i.LON 1000 puts you in control – letting you monitor, adjust, and reconfigure devices as needed, from wherever you might be.
Page 9
ORKS process control, building automation, utility, transportation, and telecommunications applications. Cisco certification is your assurance that the i.LON 1000 has been both rigorously tested and will meet the needs and standards of information technology (IT) managers worldwide. Adherence to the EIA-proposed standard for tunneling ANSI/EIA 709.1 packets over IP ensures that communications through the i.LON 1000 are both...
Page 10
1000 is fully supported by tools using Echelon's LNS™ network operating system, which provides quick setup, configuration, and application-level interoperability. From the perspective of the IT network, the i.LON 1000 is viewed as a typical IP host. Like other IP hosts, the i.LON 1000 supports standard internetworking protocols: TCP/IP, UDP, DHCP, SNMP (MIB II), ICMP, SNTP, TOS, MD5, HTTP, and FTP.
Hardware and Software Installation This chapter provides information for installing the i.LON 1000 Internet Server hardware and software with the L ORKS System Starter Kit. i.LON 1000 Internet Server Starter Kit...
Started with the L System Starter Kit. You will expand the hardware ORKS installation to include the i.LON 1000 Internet Server. The final topology is shown in figure 2.1. A picture of the actual components is shown in figure 2.2 Ethernet 10BaseT Hub...
Strip approximately 4mm of insulation away from the ends of the wire; attach one end of the twisted pair to the orange Weidmuller connector included with the i.LON 1000 and the other end to terminal 3 & 4 of the right-most LonPoint module on your DIN rail, as pictured in figure 2.2.
Page 14
Connect to the i.LON 1000 console application using Hyperterminal. a) Using the null-modem cable (not pictured in the above diagrams) that shipped with the i.LON 1000, connect an available COM port on your PC to the i.LON 1000 console port. Be sure that a modem driver, palm organizer driver, or other serial device is not already using the COM port you choose on your PC.
Page 15
Initialize the i.LON 1000’s IP address, subnet mask, and default gateway. a) Press the PC’s Enter key twice. The i.LON 1000 console application should respond with the ILON> prompt. b) Type show at the ILON> prompt and press the PC’s Enter key. The i.LON 1000 should respond with a display of its current settings.
Page 16
Once the i.LON 1000 reboots, type show at the i.LON 1000 command prompt to verify that the changes were accepted and that there are no typographical errors. Type help at the i.LON 1000’s command prompt at any time for a list of available commands. i.LON 1000 Internet Serve Starter Kit...
Page 17
Note: This is a good time to test TCP/IP communication between the PC and the i.LON 1000 by pinging the i.LON 1000 from the PC, and by pinging the PC from the i.LON 1000. Open the Windows Start menu, point to Programs, and choose the MS-DOS Prompt to open a DOS box.
Page 18
“iLON1” and select the Commission Device checkbox. Click Next. d) The next window asks you where the LonMaker tool should find information about the i.LON 1000 device. Because the i.LON 1000 adheres to the guidelines, it is not necessary to maintain a separate external interface file (XIF) describing it.
Page 19
The LonMaker tool allows you to select which channel the i.LON 1000 will be connected to. Our example network has only a single channel, the TP/FT-10 channel (named Channel 1), which the LonMaker tool automatically selects for the i.LON 1000. Click Next to accept the selection.
Page 20
Click Next to use the service pin method of device identification. This is the easiest way to get an i.LON 1000 Neuron ID into the LonMaker tool if the LonMaker PC is actually attached to the L network, like it is in ORKS this example.
Page 21
The LonMaker prompts you to press the service pin on the i.LON 1000. Using a ballpoint pen or similar object, press the recessed button marked “Service” on the back of the i.LON 1000. This causes the i.LON 1000 to send a service pin message on the L network.
Page 22
The next step is to connect input and output network variables representing the points to display in your web page to the i.LON 1000. Recall the HMI application example in Chapter 3 of Getting Started with the L ORKS System Starter Kit. In that example, an HMI application was created that monitored 4 points.
Page 23
Device list. Select Virtual Functional Block from the Functional Block list. Click Next. b) The LonMaker tool will now prompt you to name this functional block. Choose a descriptive name such as iLON WebNode. Click Finish. i.LON 1000 Internet Server Starter Kit...
Page 24
You must now add the network variables for the functional block. A powerful feature of using the LonMaker tools and i.LON 1000 together is the ability to define the network variables dynamically. In this way, you can optimize the use of network variables on the i.LON 1000 and select the exact network variable type for...
Page 25
This name must be exactly the same as the name referenced in the i.LON 1000 web page to be created later. Names are case sensitive. e) The Select Object dialog allows you to navigate the LNS object hierarchy to the point you want to monitor.
Page 26
Click OK. This instructs the LonMaker tool to create a network variable on the i.LON 1000 that is a complement to the A/AI- 1/Temperature Sensor/Analog network variable. See the LonMaker for Windows Integration Tool User’s Guide for more information on dynamic network variable creation and complement network variables.
Page 27
A | AO- 1 | Switch to Mode Translator| Data_Out nviControlValue A | AO- 1 | PID Controller | CV nvoSetPoint A | AO- 1 | PID Controller | SP When finished, your functional block should look like this: i.LON 1000 Internet Server Starter Kit...
Page 28
Right click the AI-1 hardware device shape. Select commission from the shortcut menu. n) Right click the AO-1 hardware device shape. Select commission from the shortcut menu. Save the LonMaker drawing and exit the LonMaker program. i.LON 1000 Internet Serve Starter Kit...
Working with Web Pages This chapter provides information on web pages. It includes information for creating, transferring, and viewing these pages. i.LON 1000 Internet Server Starter Kit...
(http://www.vandyke.com), or even the command line FTP client that ships with Windows, transfer demo1page1.htm and demo1page2.htm to the i.LON 1000. Place the files in the /Web/forms directory. Note that i.LON 1000 file and directory names are case sensitive. See your TCP/IP system administrator for help using FTP if you are not familiar with transferring files in a TCP/IP network.
Be sure to substitute your i.LON 1000’s IP address and to use the proper case; i.LON 1000 file names are case sensitive. Note that you do not need to include the “Web” directory in the URL. “Web” is implied because the browser makes an HTTP request.
You will notice that the HTML code required to generate this page is substantially more complex than the code for the previous page, but the network variable access mechanism is essentially the same. i.LON 1000 Internet Serve Starter Kit...
Web/images directory. Use the i.LON 1000’s DIR command and console application to verify that the transferred files ended up where you wanted them. In addition to the files that shipped with your i.LON 1000, the i.LON 1000 directory structure should contain the following files.
Using JavaScript Visit your local bookstore for a texts with more information on creative usage of JavaScript or visit the following web sites. http://devedge.netscape.com/docs/manuals/js/client/jsguide/index.htm http://developer.netscape.com/docs/manuals/js/client/jsref/index.htm http://www.wdvl.com/Authoring/JavaScript/ http://www.atl.ualberta.ca/downes/java/move_object.htm http://www.dansteinman.com/dynduo/ http://msdn.microsoft.com/workshop/c-frame.htm#/workshop/author/default.asp http://msdn.microsoft.com/scripting/ i.LON 1000 Internet Serve Starter Kit...
Troubleshooting This chapter provides suggestions for resolving problems you may have encountered in the previous chapters. i.LON 1000 Internet Server Starter Kit...
The breadth of the technology requires that tools such as LonMaker for Windows and the i.LON 1000 Internet Server provide multiple options for getting things done. If you followed the steps in Chapters 2 and 3, but did not end up with the results you expected, you may have inadvertently mistyped.
Page 37
Verify that you can ping the i.LON 1000 from your PC, and that you can ping the PC from the i.LON 1000’s console prompt. Again, your TCP/IP network administrator can help you do this.
Page 38
4.1. Figure 4.1 Restored LonMaker Drawing Note that the i.LON 1000, the i.LON 1000’s functional block, and all connections are already made. You will notice red diagonal lines across each of your devices. The network interface should appear green. The red...
Page 39
Exit the LonMaker tool. When prompted, select Yes to save your changes. Ask your TCP/IP system administrator to help you verify that the files you transferred via FTP to the i.LON 1000 were transferred, and are now located in the correct directories. Remember that resetting the i.LON 1000 back-to-factory defaults did not delete any files that you may have already transferred to the i.LON 1000.