Related Manuals for Avaya OR-II
Summary of Contents for Avaya OR-II
-
Page 1: Table Of Contents
Table of Contents Welcome Introducing Avaya Wireless LAN About the Avaya Wireless LAN OR-II Finding Information Install the OR-II Overview Verify Kit Contents Write Down Product Identification Fix Mounting Plate and Power Supply Mount the Processor Module Connect the Network Interfaces... - Page 2 Software Regulatory Information OR-II Start-up Configuration Technical Support OR-II...
-
Page 3: Welcome
Welcome to Avaya Wireless LAN, the easy way to wireless computing. This booklet introduces you to the Avaya Wireless LAN Outdoor Router-II (OR-II), and will help you to get your network “on the air” within a snap. It describes the most common configurations and a quick start set-up. -
Page 4: About The Avaya Wireless Lan Or-Ii
Welcome - About the Avaya Wireless LAN OR-II About the Avaya Wireless LAN OR-II The Avaya Wireless LAN OR-II system has been designed to serve as a wireless backbone between LANs. These LANs can be wired or wireless. Avaya Wireless LAN OR-II... -
Page 5: Finding Information
Finding Information In this booklet you will find the most important information to install your OR-II, and get it up and running. Alternatively you can consult the “ OR Manager - User’s Guide”, and the on-line help information of the OR Manager program. - Page 6 Welcome - Finding Information On-line Help Information When you install the OR Manager program, you can display context- sensitive help with each screen by: Clicking the or ‘?’ button on your screen, or Pressing the key on your keyboard. OR-II Getting Started Guide...
-
Page 7: Install The Or-Ii
6. “Mount the Cover Plate”. 7. “Power-up the Device”. 8. “Install the OR Manager Software”. Verify Kit Contents Unpack the Avaya Wireless LAN OR-II and verify that all items are present as pictured in Figure 2-1 on page 2-2. OR-II Getting Started Guide... - Page 8 Install the OR-II - Verify Kit Contents Figure 2-1 OR-II Kit Contents Mounting plate to mount the OR-II to a wall (see page 2-4). Avaya Wireless LAN OR-II processor module (see page 2-6). Power supply & AC power cord (see page 2-4).
-
Page 9: Write Down Product Identification
Figure 2-2 OR-II Identification Label You are also advised to write down the Licence Key number of the OR-II unit (printed on the same label), and the Serial Number and MAC address of the Avaya Wireless LAN PC Card(s) that you use with your OR-II (this information is printed on a small label at the back side of the PC Card). -
Page 10: Fix Mounting Plate And Power Supply
Install the OR-II - Fix Mounting Plate and Power Supply Fix Mounting Plate and Power Supply You can mount the OR-II on a vertical surface like a wall or place the unit on a flat surface such as a table or cabinet. - Page 11 Install the OR-II - Fix Mounting Plate and Power Supply Figure 2-3 Mounting the Power Supply 2. Connect the AC power cord to the power supply unit. 3. Place the power supply unit at the mid section of the mounting plate as pictured in Figure 2-3.
-
Page 12: Mount The Processor Module
Install the OR-II - Mount the Processor Module Mount the Processor Module 1. Connect the DC power cable to the DC power inlet of the processor module. 2. Sliding the four recesses of the processor module over the corresponding tabs on the mounting plate (see Figure 2-4 on page 2-6). - Page 13 Before you proceed: Verify that all four recesses are fitted correctly onto the corresponding tabs of the mounting plate. If the processor module is not properly seated, it may drop causing severe personal injury and/or causing serious damage to the OR-II unit. OR-II Getting Started Guide...
-
Page 14: Connect The Network Interfaces
Connect the Network Interfaces 1. Insert your Avaya Wireless LAN PC Card(s) into the processor module. One PC Card slot of the Avaya Wireless LAN OR-II is equipped with a plastic Slot Protector Card. The purpose of this card is to protect the OR-II unit from dust when it is used with a single Avaya Wireless LAN PC Card only. -
Page 15: Mount The Cover Plate
Install the OR-II - Mount the Cover Plate Mount the Cover Plate 1. Position the latches at the inside of the cover underneath the rim at the bottom of the processor module (see arrow-1 in Figure 2-6). Figure 2-6 Mounting the OR-II Cover Plate 2. -
Page 16: Power-Up The Device
Install the OR-II - Power-up the Device Power-up the Device To power-up the OR-II, connect the device to an AC wall-outlet with the provided AC power cord. WARNING: Placement of OR-IIs must satisfy the following installation requirements: Connect the unit to a grounding type AC wall outlet (100-240 VAC) using the standard power cord as supplied with the unit. - Page 17 A Wireless Flicker Green Wireless LAN activity interface B LED activity will only occur when there is network activity on the corresponding OR-II network interface. When there is no activity, the LED is off. OR-II Getting Started Guide 2-11...
-
Page 18: Install The Or Manager Software
Install the OR-II - Install the OR Manager Software Install the OR Manager Software Your OR-II is almost ready for use. You can configure the OR-II using the Avaya Wireless LAN OR Manager software. To install the Avaya Wireless LAN OR Manager software, proceed as follows: 1. - Page 19 Select the drive letter of your CD-ROM player in the Browse window, then select the file setup.exe, and click the Open button. Click the OK button in the Run window. The Avaya CD Browser will start-up. 4. From the Avaya CD Browser main menu, select the Install Software button, then select the Install OR Manager button.
- Page 20 OR-II program folders, these files will not be deleted or overwritten.
-
Page 21: Using Your Or-Ii
Installation must at all times conform to local regulations. e. When connecting the OR-II to an outdoor antenna system, consult the documentation that came with the outdoor antenna kit for additional regulatory information, safety instructions and installation requirements. -
Page 22: Removing The Cover Plate
Using your OR-II - Removing the Cover Plate Removing the Cover Plate Removing the cover plate of the OR-II may be required in the following situations: changing or replacing the Avaya Wireless LAN PC Card(s), or getting access to the ‘Reboot’ and/or ‘Forced Reload’ buttons on the processor module. -
Page 23: Or-Ii Specifications A1
10 to 90% (no condensation allowed) Ethernet interface 10/100Base-T RJ 45 female socket, 10/100 Mbit/s Ethernet Wireless interface 2 x PC Card Type II slot Serial interface RS232 Connector (will be supported in a future release) OR-II Getting Started Guide... - Page 24 Factory installed operating software for the Avaya Wireless LAN OR-II. This software, that is loaded into the FlashROM of the unit, controls its features and functions. The ‘xxx’ in the file name refer to the version level of the software.
- Page 25 OR-II Specifications - Regulatory Information Regulatory Information Wireless communication is often subject to local radio regulations. Although wireless networking products have been designed for operation in the license-free 2.4 GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
- Page 26 OR-II Specifications - Regulatory Information OR-II Getting Started Guide...
- Page 27 OR-II Start-up Configuration To allow for starting up your network, the OR-II has been loaded with a factory-set configuration (see page B-2). NOTE: The factory-set configuration should not be confused with a ‘default’ configuration. For example when performing a ‘reboot’ or ‘forced reload’...
-
Page 28: Or-Ii
IP Configuration table of the DHCP ot BOOTP server system. When your network includes MS-DOS stations using the Avaya Wireless LAN DOS ODI driver, you are advised to change the value to a name that consists of ‘’UPPER CASE’’... - Page 29 Alternatively please contact your local authorized Avaya Wireless LAN reseller for Technical Support. Help us helping you by completing the Avaya Wireless LAN problem report form, and include it with your e-mail or fax when contacting your local authorized Avaya Wireless LAN reseller. The report form ( ) will report_or.txt...