Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Mitsubishi Diamond Scan 90E
Summary of Contents for Mitsubishi Diamond Scan 90E
- Page 1 AUTO-SCANNING WITH DIGITAL CONTROL COLOR DISPLAY MONITOR FFT9905SKHFW MODEL USER'S GUIDE For future reference, record the serial number of your display monitor in the space below: SERIAL No. The serial number is located on the rear cover of the monitor.
- Page 2 The power cord provided with this monitor is designed for safety and must be used with a properly grounded outlet to avoid possible electrical shock. Do not remove the monitor cabinet as this can expose you to very high voltages and other hazards. この装置は、情報処理装置等電波障害自主規制協議会（VCCI）の基準に基づく...
- Page 3 MODIFY THIS EQUIPMENT. IF MODIFIED, YOUR AUTHORITY TO OPERATE THIS EQUIPMENT MIGHT BE VOIDED BY FCC. This product is not designed for use in life support devices and Mitsubishi Electric corporation makes no representations to the contrary. Life support devices are those devices which are used to measure, diagnose, or evaluate the tissue, sys- tems or functions of the human body;...
- Page 4 Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally-adapted electronic products.
- Page 5 In and after the middle of this page, you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development Unit S-114 94 Stockholm Sweden Fax: +46 8 782 92 07 E-mail (Internet): development@tco.se Current information regarding TCO'95 approved and labelled products may also be obtained via the Internet, using the address:...
-
Page 6: Table Of Contents
7.2 Serial Interface Input Connector (DIN-8P) For Serial Interface Function .. 26 7.3 SC-B102 Signal Cable ... 27 7.4 Macintosh Adapter AD-A205 settings ... 28 Note : This manual is designed for use with Diamond Scan 90e color display monitor. -
Page 7: Introduction
Once again, thank you for selecting our product and welcome to Mitsubishi! This guide tells you how to connect, adjust and care for your Diamond Scan 90e monitor. This guide also provides technical specifications and instructions for troubleshooting any basic problems you may experience with your monitor. -
Page 8: Internal Preset Memory Capability
15W. When the monitor is in suspend mode, the screen is off and the power indicator will change to amber. After the vertical sync signal is restored, picture will be displayed within a few sec- onds. -
Page 9: Ddc
When setting up and using the monitor, keep the following in mind: For optimum viewing, avoid placing the monitor against a bright background or where sunlight or other light sources may reflect on the display area of the monitor; place the monitor just below eye level. -
Page 10: Unpacking
Screen Position Adjustment Adjust the tilt and rotation of the monitor by placing your hands at opposite sides of the case, as shown in Figure 2. You can adjust the monitor 45 degrees right or left, 10 degrees up or 5 degrees down, as shown below. -
Page 11: Quick Operation Chart
1.9 Quick Operation Chart To summarize the steps in connecting your computer and adapter with Diamond Scan 90e color monitor and setting the necessary controls and switches, refer to the chart below. Connect the power cord to the Diamond Scan 90e color monitor and the signal cable between the Diamond Scan 90e and the graphics adapter. -
Page 12: Connecting The Monitor
CONNECTING THE MONITOR On the back of the monitor are four plug-in connections: one for the AC power cord, DB9-15P connector, BNC connector for video and a DIN-8P connector for the optional USB-unit. AC Power Connection One end of the AC power cord is connected into the AC power connector on the back of the monitor. -
Page 13: Connecting To An Apple Macintosh Centris, Quadra, And Apple Macintosh Ii Family
Connect the sub-miniature 15-pin (DB9-15P) end of AD-A205 Adapter to the SC-B102 cable. Connect the other end of the SC-B102 cable to the DB9-15P receptacle on the back of the monitor. Power on the Macintosh, then the monitor. After using the system, power off the monitor, then the Macintosh. D-SUB Serial DB9-15P Power Cord Please see APPENDIX (7.4 Macintosh Adapter AD-A205 settings). - Page 14 BNC CONNECTION (1) IN CASE OF A COMPOSITE SYNC ON GREEN VIDEO SIGNAL (SYNC ON GREEN): Connect the R, G and B video signals to the BNC receptacles on the back of the monitor. Serial (2) IN CASE OF EXTERNAL COMPOSITE SYNC SIGNAL: Connect the R, G and B video signals and the Composite sync signal to BNC receptacles on rear panel, respectively.
-
Page 15: User Controls
USER CONTROLS Control Names See Figure 6 and 7 for the location of the following user controls and indicators. Each control is identified by number and is described individually on page 14. FRONT 4. OSD OFF BUTTON BNC/D-SUB BNC/D-SUB 3. INPUT CONNECTOR SELECT BUTTON Function POWER SWITCH: A push-on push-off switch for AC power. - Page 16 For further information about the optional USB kit, please contact your authorized MITSUBISHI dealer. DC POWER OUTPUT CONNECTOR: Do not connect the DC power connector with any models except MITSUBISHI CAUTION USB unit. D-SUB COMP.
-
Page 17: Osd(On Screen Display) Functions
Adjusts the rotation or twist of the picture. (16) GEOMETRY-RESET: Restore to factory preset following mode; H-SIZE, H-PHASE, V-SIZE, V- POSI, SIDE-BOW, KEY STONE, PIN-BALANCE, KEY-BALANCE. (17) POWER-SAVE (ON/OFF): When adjusting ON, reduces the power consumption of the monitor when not in use. (18) VIDEO LEVEL: Selects video levels 1.0V or 0.7V. -
Page 18: Operation
Press any select button and control indicators will be superimposed on the display screen called 1st layer. Refer to Figure 6 for the location of the monitor function ( select buttons to choose one of the following controls. The indication of a function symbol changes to blue. - Page 19 CONT R AS T Symbol of 1st 2nd OSD layer OSD layer CONTRAST CON T R A S T LEVEL: 00 - 100% BRIGHTNESS BR I GH T N E S S LEVEL: 00 - 100% COLOR TEMPERATURE CO L OR - T EM P ER AT U RE LEVEL: 5000 - 9950K INFORMATION 6 9 .
- Page 20 Symbol of 1st 2nd OSD layer OSD layer H-SIZE H - S I Z E LEVEL: 00 - 100% H-PHASE H - P H A S E LEVEL: 00 - 100% V-SIZE V - S I Z E LEVEL: 00 - 100% V-POSITION V - P OS I T I ON LEVEL: 00 - 100%...
- Page 21 Symbol of 1st 2nd OSD layer OSD layer KEYSTONE KE Y S T ONE LEVEL: 00 - 100% PIN-BALANCE P I N - B AL A NCE LEVEL: 00 - 100% KEY-BALANCE KE Y - B AL A NCE LEVEL: 00 - 100% H-MOIRE H - MO I RE LEVEL: 00 - 100%...
- Page 22 Symbol of 1st 2nd OSD layer OSD layer ROTATION RO T A T I ON LEVEL: 00 - 100% GEOMETRY RESET GEOME T R Y - R E S E T C A NC E L P ROCEED POWER-SAVE POWER - S A V E O F F VIDEO-LEVEL V I D EO - L E V E L...
- Page 23 Symbol of 1st 2nd OSD layer OSD layer USB PORT SELECT USB S T A T US P L E A S E C H E CK MO N I T OR CO N NE C T I ON OR USB IS S US P E NDED ADJUST LOCK 1.
-
Page 24: Power Save
POWER SAVE N O T E When the monitor has no sync signal or incorrect connection and the signal frequency is out of range, the following CAUTION comes on the screen. Check input signal, signal cable connection and signal frequency. -
Page 25: Troubleshooting
• Adjust H.SIZE, V.SIZE, H.PHASE, and V.POSITION with non-standard signals • Monitor may not be able to get full-screen image Display is missing, depend on signal. In this case, please select other center shifts, or resolution, or other vertical refresh timing. -
Page 26: Specifications
SPECIFICATIONS Size Mask type Deflection angle Phosphors Dot pitch Face Plate Focusing method INPUT SIGNAL Video Sync INTERFACE Input Connector Input Impedance SCANNING Horizontal FREQUENCY Vertical RESOLUTION (HxV) 1600dots x 1200lines Non-Interlaced maximum addressable resolution format at 75Hz WARM-UP TIME 30 minutes to reach optimum performance level ≧100cd/m BRIGHTNESS... -
Page 27: Appendix
APPENDIX Monitor Signal Input Connector (DB9-15P) (Female) DB9-15P MOUNTED ON THE REAR PANEL DDC ... DISPLAY DATA CHANNEL SDA ... SERIAL DATA SCL ... SERIAL CLOCK NC ... NO-CONNECTION Serial Interface Input Connector (DIN-8P) For Serial Interface Function (Female) DIN-8P... -
Page 28: Sc-B102 Signal Cable
SC-B102 Signal Cable PIN ASSIGNMENT AND SIGNAL LEVEL Approx. 1.8m DB9-15P (Male) ASSIGNMENT SIGNAL LEVEL NC ... NO-CONNECTION DDC: DISPLAY DATA CHANNEL SDA: SERIAL DATA SCL: SERIAL CLOCK DB9-15P (Male) Wire : 5 coaxial SIGNAL ANALOG GREEN BLUE GROUND DDC GROUND RED GROUND GREEN GROUND BLUE GROUND... -
Page 29: Macintosh Adapter Ad-A205 Settings
(see 1.2 Internal Preset Memory Capability) The chart shows all available modes for Macintosh systems plus all possible combinations with monitor. Please be aware that not all Macintosh modes are capable of driving all Macintosh video modes. - Page 30 AD-A205 Mac Adapter settings Chart Macintosh Macintosh Macintosh Macintosh IIci LC,LC II LC III, COMPUTER -or- LC 475 IIsi Performa -or- 400,405, Performa 450,460, 410,430 466,467, RESOLUTION 475,476 640X480@60Hz 640X480@67Hz 800X600@56Hz 800X600@60Hz 800X600@72Hz 800X600@75Hz 832X624@75Hz 1024X768@60Hz 1024X768@70Hz 1024X768@72Hz 1024X768@75Hz 1024X768@75Hz 1152X870@75Hz 1280X960@75Hz 1280X1024@75Hz...
- Page 31 CP871C144A90 MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE: MITSUBISHI DENKI BLD, MARUNOUCHI, TOKYO 100-0005 TELEX J24532 CABLE MELCO TOKYO...