Advertisement
Quick Links
Advertisement
Related Manuals for JUKI PLC-2710N-7
Summary of Contents for JUKI PLC-2710N-7
- Page 1 PLC-2710N-7,2760N,2760N-7,2760NL INSTRUCTION MANUAL...
-
Page 2: Table Of Contents
3-3. Setting the ancillary device (PLC-2760N,2760NL) ..........7 3-4. Piping of the air (PLC-2760N,2760NL) ..............8 CAUTION This Instruction Manual for the PLC-2710N-7,2760N,2760N-7,2760NL only describes their dif- ferences from the standard models (PLC-2710-7,2760,2760-7,2760L). For safety-related information, carefully read and fully understand "Safety precautions"... -
Page 3: Specifications
19 Thread trimming method 20 Lubrication Automatic lubrication by oil tank (with oil gauge) 21 Lubricating oil JUKI New Defrix Oil No. 1 (equivalent to ISO standard VG7) or JUKI MACHINE OIL No. 7 22 Bed size 643 mm × 178 mm 23 Space under the arm 347 mm ×... - Page 4 Cam-driven scissors type 20 Lubrication Automatic lubrication by oil tank (with oil gauge) 21 Lubricating oil JUKI New Defrix Oil No. 1 (equivalent to ISO standard VG7) or JUKI MACHINE OIL No. 7 22 Bed size 643 mm × 178 mm 23 Space under the arm 347 mm ×...
-
Page 5: Threading The Machine Head
2. Threading the machine head [PLC-2710N-7] WARNING : To protect against possible personal injury due to abrupt start of the machine, be sure to start the following work after turning the power off and ascertaining that the motor is at rest. - Page 6 [PLC-2760N, 2760N-7, 2760NL] WARNING : To protect against possible personal injury due to abrupt start of the machine, be sure to start the following work after turning the power off and ascertaining that the motor is at rest. Thread the machine head following the order as illustrated in the figure.
-
Page 7: Setting The Pneumatic Center Guide (Plc-2760N,2760N-7,2760Nl)
3. Setting the pneumatic center guide (PLC-2760N,2760N-7,2760NL) ❶ Ⓐ Ⓑ ❷ ❸ ❹ ❺ ❻ ❼ 3-1. Selection of the optional input function switch ❼ , turn the power ON. (The display items that have been changed While holding down in the previous operation will be displayed.) * If the screen display does not change, start over the operation again from the beginning. -
Page 8: Selection Of The Optional Output Function
3-2. Selection of the optional output function Select the function No. 12 with the operating procedure of the optional input setting procedures 1 and 2. Select the item of "oUT" with keys ❺ and ❻ . Select o13/o15 with key ❹ . *1 Select the "CGUd"... -
Page 9: Setting The Ancillary Device (Plc-2760N,2760Nl)
3-3. Setting the ancillary device (PLC-2760N,2760NL) ❶ Ⓐ Ⓑ ❷ ❸ ❹ ❺ ❻ ❼ switch ❼ , turn the power ON. While holding down If you keep the switch held pressed for three seconds or more, the buzzer will sound to allow you to set the functions that are available under the Service mode. -
Page 10: Piping Of The Air (Plc-2760N,2760Nl)
3-4. Piping of the air (PLC-2760N,2760NL) CN152 CN154 CN155 CN153 CN151 Center guide (Wire mark ⑩ ) (With no wire mark) Plug (Wire mark ⑧ ) (PX950013000) (Wire mark ⑥ ) Connect the air hose coming from the machine head to the position shown above while matching the number of the air hose and the number of the port.