Remote Control; How To Install Batteries; Battery Precautions - Memorex MT1125A Owner's Manual

REMOTE CONTROL

POWER
TV/AV
1
1 2
5 6
2
0
9
3
MUTING
4
SLEEP
5
MENU SET
6
AUDIO
7 RESET SELECT
8
9
1. POWER Button - Press to turn the TV on. Press again
to turn the TV off.
2. Direct Channel Selection Buttons (0-9) - Allows direct
access to any channel.
3. MUTING Button - To turn off the sound, press this
button once. The TV will be silenced and the symbol
"MUTING" will appear on the screen. The muting feature
can be released by pressing the MUTING button again
or one of the VOL or
4. VOL (VOLUME) / Buttons - Press the
increase, or the button to decrease the volume level.
Before using the remote control, batteries must first be installed into it.

HOW TO INSTALL BATTERIES

1. Open the battery compartment cover.
2. Install two "AAA" batteries.
3. Replace the battery compartment cover.
3i01101A E
10
3 4
11
7
8
QUICK
VIEW CALL
12
VOL
CH
13
ENTER
14
CH.1/2
TV
15
CAPTION/TEXT
16
button.
button to
5
5. SLEEP Button - To set the TV to turn off after a preset
amount of time, press the SLEEP button on the remote
control. The clock will count down 10 minutes each time
the button is pressed in the order of 120, 110, 100, ······
20, 10, 0. After the sleep time is programmed, the
display will disappear then reappear momentarily every
ten minutes to remind you the sleep timer function is
operating. To confirm the sleep time setting, press the
SLEEP button once and the remaining time will be
momentarily displayed. To cancel sleep time, press the
SLEEP button repeatedly until the display turns to 0.
6. MENU Button - Press to display the On-Screen menu
function.
7. SET + / – Buttons - Press to select the desired setting
during On-Screen operations.
8. RESET Button - Press to reset the On-Screen picture
adjustments to their factory preset positions. Press to
reset a password in the V-CHIP Password setting mode.
9. AUDIO SELECT Button - Switches sound between
mono and stereo, and SAP when receiveing broadcasts
in stereo or SAP.
10. TV/AV Button - Switches between TV and external
inputs.
11. QUICK VIEW Button - This button allows you to go
back to the previous channel selected by just pressing
the QUICK VIEW button. Press this button again to return
to the channel you were watching.
12. CALL Button - When you press this button, the channel
number tuned will appear on the upper right corner of
the screen. Press the button again to remove display
from the screen.
13. CH (CHANNEL) / Buttons - Press the
change to a higher numbered channel set into memory.
Press the button to change to a lower numbered
channel set into memory.
14. ENTER Button - Press to enter or select information for
On-Screen operations.
15. CH.1/2 Button - Switches between Channel 1and
Channel 2 in the Closed Caption mode.
16. TV/CAPTION/TEXT Button - Press this button to switch
between normal TV and the two Closed Caption modes
(captions and 1/2 of full screen text). Closed Captioning
will display text on screen for hearing impaired viewers.
Use two "AAA" size batteries. The batteries may last
approximately one year depending on how much the remote
control is used. For best performance, it is recommended
that batteries should be replaced on a yearly basis, or when
the remote operation becomes erratic. Do not mix old and
new batteries or different types.

BATTERY PRECAUTIONS

These precautions should be followed when using batteries
in this device:
• Use only the size and type of batteries specified.
• Be sure to follow the correct polarity when installing the
batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g.
Alkaline and Carbon-zinc) or old batteries with fresh ones.
• If the device is not to be used for a long period of time,
remove the batteries to prevent damage or injury from
possible battery leakage.
• Do not try to recharge batteries not intended to be re-
charged; they can overheat and rupture. (Follow battery
manufacturer's directions.)
28.09.99, 13:20
button to
5