Black & Decker REVHD12C H1 Original Instructions Manual page 9

Slide the speed selector (6) towards the front of the tool (2nd
gear).
Screwdriving
Always use the correct type and size of screwdriver bit.
u
If screws are difficult to tighten, try applying a small
u
amount of washing liquid or soap as a lubricant.
Always hold the tool and screwdriver bit in a straight line
u
with the screw.
Troubleshooting
Problem Possible cause
Unit will not Battery not
start. charged.
Battery will not Charger not plugged
charge. in.
Surrounding air
temperature too hot
or too cold.
Unit shuts off Battery hasreached
abruptly. its maximum
thermal limit.
Out of charge. (To
maximize the life of
the battery it is
designed to shutoff
abruptly when the
charge is
depleted
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any cleaning or maintenance on
the tool, unplug the charger.
Regularly clean the ventilation slots in your tool using a
u
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed
of with normal household waste.
Products and batteries contain materials that can be recov-
ered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions.
Possible solution
Check battery charging
requirements
Plug charger into a working
outlet.
Move charger to a surrounding air
temperature of above 40
degrees F (45ºC) or below
105 degrees F (+40.5ºC)
Allow battery to cool down.
Place on charger and allow to
charge.
(Original instructions)
Further information is available at
www.2helpU.com
Technical data
Voltage
V
DC
No-load speed
min
Max. torque Nm
Chuck capacity mm
Max Drilling capacity
Steel/Wood/Masonry mm
Weight kg
Integral Battery
Battery type
Ah rating
Charger
Input Voltage V
AC
Output voltage V
DC
Current
mA
Approx. charge time
h
Level of sound pressure according to EN 62841:
Sound pressure (L
Sound power (L ) 95 dB(A), uncertainty (K) 5 dB(A)
WA
Vibration total values (triax vector sum) according to EN 62841:
Drilling metal (a ) 0.9 m/s
h
Hammer drilling into concrete (a
Declaration of conformity
The Supply of Machinery (Safety)
Regulations 2008
REVHD12C Impact Drill
Black & Decker declares that these products described under
"technical data" are in compliance with:
The Supply of Machinery (Safety) Regulations, 2008, S.I.
2008/1597 (as amended),
EN62841-1:2015, EN62841-2-1:2018+A11:2019.
These products also conform to the following UK Regulations:
Electromagnetic Compatibility Regulations, 2016,
S.I.2016/1091 (as amended).
ENGLISH
REVHD12C H1
0-350 / 0-1350 /min (RPM)
-1
10 / 25 / 10
S010*1400040
) 84, uncertainty (K) 5 dB(A)
pA
2 2
, uncertainty (K) 1.5 m/s
2
) 17.1 m/s , uncertainty (K) 1.5 m/s
h
12
17.5/40
1-10
1.0
Li-Ion
1.5
230
10.8
400mA
4
2
9