Traxxas 7885 Installation Instructions

LED Light Bar Kit Installation Instructions
Kit Contents:
• High-Voltage Power Amplifier*
• 3x12mm button-head screws (2)
• Front LED light bar*
• 3x8mm cap-head screws (2)
• Rear LED light bar mount*
†
• 3x10mm flat-head screws (2)
Tools needed (all not included and sold separately):
• Tapered body reamer
(part #3433 or #3433X)
• 1.5mm hex wrench
• 2.0mm hex wrench
• 2.5mm hex wrench
CAUTION: RISK OF INJURY!
hobby knives, tapered reamers, and other cutting tools as they are
extremely sharp and can cause severe injury, deep cuts, and/or punctures.
1 XRT
BODY UNDERSIDE VIEW
8mm Hole
XRT™ Body Modification
Using a tapered body reamer, carefully cut a
small 8mm hole in the truck body. The hole
needs to be large enough for the rear light
bar harness connectors to pass through (note
the hole diameter measurements on the body
reamer).
1 X-MAXX
X-Maxx® Body Modification
Install the included template on the truck body. Align the arrows with
the roof line and rear window as shown. Using a tapered body reamer,
carefully cut the holes in the truck body for the screw bosses on the
rear LED light bar mount and the rear light bar connectors (note the
hole diameters indicated on the templates and the corresponding diameter
measurements on the body reamer).
Traxxas, 6250 Traxxas Way, McKinney, TX 75070, Phone: 972-549-3000, Fax: 972-549-3011, e-mail: support@Traxxas.com
• Rear LED light bar*
• 3x8mm button-head screws (2)
• Extension harness (long)*
• Extension harness (short)*
• 3x10mm button-head screws (2)
• Zip ties (10)
Compatible with the following Traxxas
electronic speed controls (sold separately):
Velineon® VXL-6s (part #3485)
Velineon® VXL-8s (part #3496)
Use care with
FRONT
Tapered Body Reamer
Diameter Measurements
#7882*
2 XRT
3x12mm
BCS
Install the high-voltage power amplifier on the truck chassis. Ensure that
the connectors on the amplifier face the front of the vehicle. Secure with
the 3x12mm button-head screws.
3 XRT 3 X-MAXX
Remove the 3x25mm button-
head screws (2) from the
electronic speed control (ESC)
to remove the cooling fan cover.
Remove the accessory port
cover; then, reinstall the cooling
fan cover on the ESC using the
3x25mm button-head screws.
Be careful not to pinch the ESC
wires during reinstallation.
REAR
4 XRT 4 X-MAXX
CAUTION: RISK OF DAMAGE TO
ELECTRONICS!
speed control (ESC) and/or the high-voltage power amplifier, ensure the
battery is disconnected before plugging the amplifier into the ESC.
TR A XXA S .c om
Visitez Traxxas.com/manuals pour télécharger
les instructions dans votre langue.
Visite la página Traxxas.com/manuals para
descargar el instrucciones en su idioma.
Auf Traxxas.com/manuals, können Sie
anleitung in Ihrer Sprache downloaden.
#7882*
#7883*
†
#7883*
#7884*
*parts also available separately
2 X-MAXX
FRONT
3x25mm BCS
To prevent damage to the electronic
Covers Part #7885
#6590*
not required for XRT
†
FRONT
3x12mm BCS
Accessory Port
Cover
Plug the 8-pin connector
from the high-voltage
power amplifier into the
accessory port on the
ESC. The amplifier and
lights will turn on when
the ESC is powered on.
HKC18090-R04 Rev 221110