DeWalt DCG418 Manual
  1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Grinder
  5. XR LI-ION DCG418
  6. Manual

DeWalt DCG418 Manual

Hide thumbs Also See for DCG418:
Table of Contents

Advertisement

Quick Links

Download this manual
DCG418
Final Page size: A5 (148mm x 210mm)

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DCG418

Summary of Contents for DeWalt DCG418

  • Page 1 DCG418 Final Page size: A5 (148mm x 210mm)
  • Page 2 English (original instructions) Copyright D WALT...
  • Page 3 Fig. A 90˚ 90˚ Fig. B...
  • Page 4 Fig. C Fig. D Fig. E...
  • Page 5 Fig. F > 3.17 mm < 3.17 mm Fig. G Fig. H Fig. I Fig. J...

  • Page 6: Technical Data

    English CORDLESS SMALL ANGLE GRINDER DCG418 Congratulations! hands warm (relevant for vibration), organisation of work patterns. You have chosen a D WALT tool. Years of experience, thorough EC-Declaration of Conformity product development and innovation make D WALT one of the most reliable partners for professional power tool users.

  • Page 7: Work Area Safety

    *Date code 202011475B or later **Date code 201536 or later English Batteries Chargers/Charge Times (Minutes) Weight (kg) DCB104 DCB107 DCB112 DCB113 DCB115 DCB116 DCB117 DCB118 DCB132 DCB119 Cat # DCB546 18/54 6.0/2.0 1.05 DCB547 18/54 9.0/3.0 1.46 135* 110* 135* DCB548 18/54 12.0/4.0...

  • Page 8: Additional Specific Safety Rules

    English connected and properly used. Use of dust collection d ) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact can reduce dust-related hazards. accidentally occurs, flush with water. If liquid h ) Do not let familiarity gained from frequent use of contacts eyes, additionally seek medical help.

  • Page 9: Causes And Operator Prevention Of Kickback

    English r ) Always use side handle. Tighten the handle securely. run out of balance, vibrate excessively and may cause loss of control. The side handle should always be used to maintain control of the tool at all times. g ) Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheel for WARNING: We recommend the use of a residual current chips and cracks, backing pad for cracks, tear or...
  • Page 10 English b ) The grinding surface of centre depressed wheels wheel may cut gas or water pipes, electrical wiring or must be mounted below the plane of the guard lip. objects that can cause kickback. An improperly mounted wheel that projects through the Safety Warnings Specific for Sanding plane of the guard lip cannot be adequately protected.

  • Page 11: Using An Extension Cable

    English WARNING: No connection is to be made to the Do not place any object on top of charger or place • the charger on a soft surface that might block the earth terminal. ventilation slots and result in excessive internal heat. Follow the fitting instructions supplied with good quality plugs.

  • Page 12: Wall Mounting

    English The compatible charger(s) will not charge a faulty battery pack. The battery pack is not fully charged out of the carton. Before The charger will indicate faulty battery by refusing to light. using the battery pack and charger, read the safety instructions below.

  • Page 13: Storage Recommendations

    English Transportation certain shipping regulations that are imposed upon the higher Watt hour batteries. WARNING: Fire hazard. Transporting batteries can For example, the Transport Example of Use and Transport Label Marking possibly cause fire if the battery terminals inadvertently Wh rating might indicate come in contact with conductive materials.

  • Page 14: Assembly And Adjustments

    Package Contents Gear case slots Intended Use The package contains: 1 Angle grinder The DCG418 cordless angle grinder has been designed for professional cutting, grinding, sanding and wire 1 125 mm Guard (Type 27) brush applications. 1 Side handle DO nOT use under wet conditions or in the presence of 1 Flange set flammable liquids or gases.
  • Page 15 English WARNING: The side handle should always be used to maintain control of the tool at all times.  5  Screw the side handle  tightly into one of the holes on either side of the gear case. To improve user comfort, the gear case will rotate 90° for cutting operations.

  • Page 16: Prior To Operation

    English or while in use. Undetectable damage could occur to 3. Place wheel against the backing flange, centreing the wheel on the raised centre (pilot) of the backing flange. the accessory, causing wires to fragment from accessory 4. While depressing the spindle lock button and with the wheel or cup.
  • Page 17 English Support panels or any oversized workpiece subject to variation based on product components, temperature • to minimize the risk of wheel pinching and and end-user application. kickback. Large workpieces tend to sag under their Proper Hand Position (Fig. A, I) own weight. Supports must be placed under the WARNING: To reduce the risk of serious personal injury, workpiece near the line of cut and near the edge of the ALWAYS use proper hand position as shown.
  • Page 18 English Environmental safety 1. Paint should be removed in such a manner as to minimize the amount of dust generated. 2. Areas where paint removal is occurring should be sealed Angle with plastic sheeting of 4 mils thickness. 3. Sanding should be done in a manner to reduce tracking of 3.

  • Page 19: Cutting Metal

    English Metal Applications WARNING: To reduce the risk of serious personal injury, turn tool off and disconnect battery pack When using the tool in metal applications, make sure that a before making any adjustments or removing/ residual current device (RCD) has been inserted to avoid residual installing attachments or accessories.
  • Page 20 English Grinding and Cutting Accessory Chart guard Type Accessory Description how to Fit grinder Depressed centre grinding disc Type 27 Type 27 guard Guard Flap wheel Backing flange Wire wheels Type 27 depressed centre wheel Threaded clamp nut Wire wheels with threaded nut Type 27 guard Wire wheel...
  • Page 21 English Grinding and Cutting Accessory Chart (cont.) guard Type Accessory Description how to Fit grinder Masonry cutting disc, bonded Type 1 Type 1 guard Guard Metal cutting disc, bonded Backing flange Diamond cutting wheels Type 1 Guard Cutting wheel Threaded clamp nut Type 27 Guard...
  • Page 24 Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België en Luxemburg Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)

Table of Contents