Konica Minolta bizhub C3120i Setup Manual page 6

Do not place any objects around the power plug, as the
power plug may be difficult to pull out when an emergency
occurs.
Do not tug the power cord when unplugging. Pulling on the
power cord could damage the cord, resulting in a fire or
electrical shock.
Remove the power plug from the outlet more than one time
a year and clean the area between the plug terminals. Dust
that accumulates between the plug terminals may cause a
fire.
<Installation>
Keep this bag away from babies and children. Do not use in
cribs, beds, carriages, or playpens. The thin film may cling
to nose and mouth and prevent breathing. This bag is not a
toy.
Do not place a flower vase or other container that contains
water, or metal clips or other small metallic objects on this
product. Spilled water or metallic objects dropped inside
the product could result in a fire, electrical shock, or
breakdown.
Should a piece of metal, water, or any other similar foreign
matter get inside the product, immediately turn OFF the
power switch, unplug the power cord from the power outlet,
and then call your Technical Representative or your
authorized service representative.
Make sure that the power cord is placed on a site in which
no person would step on or trip over it. Stepping on or
tripping over the power cord could heat the power cord,
resulting in a fire or electric shock.
<If instructed to use fixing legs>
When the product has been installed, fix the product using
the fixing legs.
Not using the fixing legs could cause the product to move or
topple over.
Do not place the product in a dusty place, or a site exposed
to soot or steam, near a kitchen table, bath, or a humidifier.
A fire, electrical shock, or breakdown could result.
Do not place this product on an unstable or tilted bench, or
in a location subject to a lot of vibration and shock. It could
drop or fall, causing personal injury or mechanical
breakdown.
Do not let any object plug the ventilation holes of this
product. Heat could accumulate inside the product,
resulting in a fire or malfunction.
Whenever moving this product, be sure to disconnect the
power cord and other cables. Failure to do this could
damage the cord or cable, resulting in a fire, electrical
shock, or breakdown.
When moving this product, always hold it at the locations
specified in the User's Guide or other documents. If the unit
is moved while held at locations other than those specified,
it may fall, causing severe personal injury.
<Using the product>
Do not modify this product, as a fire, electrical shock, or
breakdown could result. If the product employs a laser, the
laser beam source could cause blindness.
6
Do not attempt to remove the covers and panels which have
been fixed to the product. Some products have a
high-voltage part or a laser beam source inside that could
cause an electrical shock or blindness.
Do not keep using this product, if this product becomes
inordinately hot or emits smoke, or unusual odor or noise.
Immediately turn OFF the power switch, unplug the power
cord from the power outlet, and then call your Technical
Representative or your authorized service representative.
If you keep on using it as is, a fire or electrical shock could
result.
Do not keep using this product, if this product has been
dropped or its cover damaged. Immediately turn OFF the
power switch, unplug the power cord from the power outlet,
and then call your Technical Representative or your
authorized service representative. If you keep on using it as
is, a fire or electrical shock could result.
Do not use flammable sprays, liquids, or gases inside or
near this machine. Do not clean the inside of this machine
using a flammable gas duster. A fire or explosion could
result.
<If an RFID module (limited only to 13.56 MHz) for use in
inside-the-machine proximity communication or
electromagnetic induction heating (IH) technology (limited
only to 20.05 kHz to 100 kHz) is being used>
This machine generates a weak magnetic field.
If you experience any unusual symptoms with your
implantable medical equipment (cardiac pacemaker, etc.)
while near the machine, move away from the machine and
see a doctor immediately.
Please call your Technical Representative or your authorized
service representative if you do not understand the
purchased product corresponds or not.
<If a non-contact IC card reader is being used>
If you use an implantable medical equipment (cardiac
pacemaker, etc.), do not bring the IC card reader close from
the implant within 12 cm at all times.
The radio waves may affect implantable medical equipment
(cardiac pacemaker, etc.) operations.
Using this product in a poorly ventilated room for a long
time or producing a large volume of copies or prints may
cause the odor of exhaust air from the machine. Ventilate
the room well.
The inside of this product has areas subject to high
temperature, which may cause burns.
When checking the inside of the unit for malfunctions such
as a paper misfeed, do not touch the locations (around the
fusing unit, etc.) which are indicated by a "Caution HOT"
caution label. A burn could result.
Unplug the product when you will not use the product for
long periods of time.
When using the machine, do not look at the light of the lamp
for a prolonged time. Eyestrain could result.
Do not use stapled paper, conductive paper (such as silver
paper or carbon paper) or treated heat-sensitive/inkjet
paper, otherwise a fire may result.
<Consumables>
Do not throw toner or a container that contains toner (e.g.,
toner cartridge, developing unit and Waste Toner Box) into
an open flame. The hot toner may scatter and cause burns
or other damage.