Related Manuals for Electrolux DC6-14HP
Summary of Contents for Electrolux DC6-14HP
- Page 1 Installation manual Drying Cabinet DC6-14HP 427001217/EN Original instructions 2022.03.18...
-
Page 3: Table Of Contents
Contents Contents 1 Safety Precautions ..........................5 General safety information......................5 Symbols............................5 2 Technical data.............................6 Dimensions drawing........................6 Technical data ...........................7 3 Delivery ..............................8 Transport unit ..........................8 Box 1 ............................9 Recommended tools ........................9 Placement ..........................10 Ventilating the room .........................10 4 Assembly instructions ........................11 Bottom plate .......................... -
Page 5: Safety Precautions
Installation manual 1 Safety Precautions This appliance can be used in public areas. Remove all objects from pockets such as lighters and matches. WARNING. This appliance is intended only for drying textiles washed in water. DO NOT MODIFY THIS APPLIANCE. Servicing shall be carried out only by authorized personnel. -
Page 6: Technical Data
Installation manual 2 Technical data 2.1 Dimensions drawing fig.W01309 1805 1805 1560 2245 1180 Condensation outlet ⌀ 32 (see page 13) Electrical connection (see page 12) -
Page 7: Technical Data
Installation manual 2.2 Technical data Capacity: max. 10 kg of laundry Drainage capacity: 80 g/min (10 kg 55% residual moisture) Electrical connection: 400V 3N AC 50Hz Fuse 10A slow-blow, 10A automatic fuse. Power: 3.2 kW Hanging length: 22 meters Dimensions: Height 1805 mm Width... -
Page 8: Delivery
Installation manual 3 Delivery The cabinet is delivered unassembled on a transport unit. The cabinet component is assembled as instructed in this manual. After assembly, the heat pump component is hooked onto the cabinet component. The heat pump component is fully assembled upon delivery. The cabinet component and heat pump components are delivered in a single package. -
Page 9: Box 1
Installation manual 3.2 Box 1 Box 1 contains 9 bags. The content of these is found in the installation instructions below. fig.W01311 User Manual (OM) / Installation Manual (IM) / Assembly Instructions / Wiring Diagram / Disposal Instructions 3.3 Recommended tools fig.W01312 Bits Torx, T10, T20, T25, T30. -
Page 10: Placement
Installation manual 3.4 Placement The drying cabinet intended for placement indoors in dry place. Place the bottom plate in the final position of the drying cabinet. The drying cabinet should be positioned so that there is plenty of room for working, both for the user and service personnel. -
Page 11: Assembly Instructions
Installation manual 4 Assembly instructions 4.1 Bottom plate fig.W01313 Bag / Quantity Box 1 Cover plug M4x12 End cap Cover plug Lock nut M4 Magnetic holder Magnet Foot screw... -
Page 12: Back Piece
Installation manual 4.2 Back piece fig.W01314 Bag / Quantity Box 1 M6x10... -
Page 13: Side Pieces
Installation manual 4.3 Side pieces fig.W01315 Bag / Quantity Box 1 M6x10 M6x10 4.4 Roof fig.W01316 Bag / Quantity Box 1 M6x10 Cover RTK B8, 4.2x6.5... -
Page 14: Doors
Installation manual 4.5 Doors fig.W01317 Bag / Quantity Box 1 Lock nut Magnet M4x12 Handle... -
Page 15: Door Adjustment
Installation manual 4.6 Door adjustment fig.W01318 Bag / Quantity Box 1 Washer 7x12x1.5... -
Page 16: Wall Bracket
Installation manual 4.7 Wall bracket fig.W01319 Bag / Quantity Box 1 M6x16 Lock washer 6.4x11x0.7 Washer 16x6x1 Wall bracket... -
Page 17: Glove Hanger
Installation manual 4.8 Glove hanger fig.W01320 Bag / Quantity Box 1 M5x14 Plastic washer 5.3x15x1.2 Washer 5x13x1 Nylock M5... -
Page 18: Lint Filter
Installation manual 4.9 Lint filter fig.W01321 Bag / Quantity Box 1 Screws Filter holder Lint filter The filter is held by 4 screws and a filter holder. -
Page 19: Hanger Assembly
Installation manual 4.10 Hanger assembly fig.W01322 Bag / Quantity Box 1 Plastic washer 8x25x1.5 Washer 8x25x1.5 Lock nut M8 M8x75... - Page 20 Installation manual fig.W01323 Bag / Quantity Box 1 Metal screw 4.32x32 Washer 4x10x1 Door stop...
-
Page 21: Hanger Installation
Installation manual 4.11 Hanger installation fig.W01324 Bag / Quantity Box 1 Spacer plate (Chapter 4.4 Roof) Upper bracket Lower bracket X = X 0 - 2x fig.W01325... -
Page 22: Installing The Heat Pump Component On The Cabinet
Installation manual 4.12 Installing the heat pump component on the cabinet fig.X02470 The heat pump is fastened with 8 screws with washers. • Adjust the adjustable feets on the heat pump part to match the screws holding the heat pump to the body. •... -
Page 23: Install The Control Panel
Installation manual 4.13 Install the control panel fig.W01327 Bag / Quantity Box 1 4x9.5 SHEETtracs... -
Page 24: Electrical Connection
Installation manual 5 Electrical connection The electrical installation may only be performed by qualified personnel. Electrical connection of the cabinet must be done in accordance with electrical safety regulations. Make sure that the connection current is in line with the data on the identification plate and that the mains cable is grounded properly according to the applicable standard. -
Page 25: Network Functions
Installation manual 5.1 Network Functions Note! Can only be used on premium products. This product can be connected to ELS VISION or to an external payment system. fig.W01529 Connecting to ELS Vision Connect the network cables GND, RX, TX, 24V to the terminal block as illustrated. Connect the neutral position switch to terminal block positions 1 and 2, as illustrated. - Page 26 Installation manual Use the program buttons to move to Parameter 117, and enter the parameter using the Stop button. Set the parameter value to 1. This will activate the cabinet for network use. Use the Stop button to exit the parameter. To confirm the new settings: Press the Stop button and then Butterfly.
-
Page 27: Condensation Connection
Installation manual 6 Condensation connection The condensation outlet is located under the heat pump component as illustrated in the form of a pipe with a 32 mm diameter. Connect a suitable hose and route it to the floor drain. fig.W01329 Pipe connection for condensation, dia 32 mm... -
Page 28: Function Check
Installation manual 7 Function check May only be performed by qualified personnel. A function check must be performed when the installation is finished and before the appliance can be used. Whenever a repair has been made, a function check must be performed before the appliance can be used again. •... -
Page 29: Disposal Information
Installation manual 8 Disposal information 8.1 Disposal of appliance at end of life Before disposing of the machine, make sure to carefully check its physical condition, and in particular any parts of the structure that can give or break during scrapping. The machine’s parts must be disposed of in a differentiated way, according to their different characteristics (e.g. - Page 32 Electrolux Professional AB 341 80 Ljungby, Sweden www.electroluxprofessional.com...