Sony ILCE-5100 Service Manual page 11

Ver. 1.2 2014.09
2-1-3. BT SECTION
ns: not supplied
OFF position
BT001
(Note 1)
107
106
(Note 3)
105
(Note 3)
4
Imager Block Section
(See page 2-7)
3
102
Ref. No. Part No. Description
101 X-2590-046-1 HOLDER ASSY (783) (BK), BT (BLACK)
101 X-2590-047-1 HOLDER ASSY (783) (WH), BT (WHITE)
101 X-2590-048-1 HOLDER ASSY (783) (BR), BT (BROWN)
102 4-527-066-01 PLATE (FRONT) (773)
103 1-893-438-11 IS-1017 FLEXIBLE BOARD
104 1-893-439-11 IS-1018 FLEXIBLE BOARD
105 4-542-512-01 SHEET (L) (783), RING HEAT (Note 3)
106 4-542-511-01 SHEET (G) (783), RING HEAT (Note 3)
107 A-2060-485-A FRONT SERVICE BLOCK ASSY (BK) (BLACK)
107 A-2060-486-A FRONT SERVICE BLOCK ASSY (WH) (WHITE)
107 A-2060-487-A FRONT SERVICE BLOCK ASSY (BR) (BROWN)
108 4-546-055-01 INSULATING SHEET (JACK) (783)
109 A-2061-811-A SERVICE BLOCK ASSY, RL
110 A-2058-055-A AN-1007 BOARD, COMPLETE
111 A-2061-810-A SERVICE BLOCK ASSY, ANTENNA
ILCE-5100/5100L/5100Y_L2
111
ns
117
112
ns
ns
ANT901
BH001
(Note 1)
#9
#140
(Rib)
2
(Claw) 109
110
(Rib) 113
ns (Note 2)
C901
114
103
#9
104
#9
101
1
108
: BT001 (LITHIUM RECHARGEABLE BATTERY)
Board on the mount position.
(See page 6-34 of Level 3)
Ref. No. Part No. Description
112 1-846-474-21 CABLE, COAXIAL (85MM)
113 A-1992-992-A ST-1019 FLEXIBLE BOARD, COMPLETE (Note 2)
114 4-456-090-01 SPRING (BT DISCHARGE) (762)
115 A-1992-997-A BT-2002 FLEXIBLE BOARD, COMPLETE
116 4-542-510-01 SHEET (SY-F) (783), RADIATION
117 4-489-139-01 SHEET, DL FPC
ANT901 A-1975-721-A ANTENNA (SERVICE), NFC
BH001 1-251-928-21 SOCKET, BATTERY (Note 1)
BT001 1-756-134-15 BATTERY, LITHIUM (SECONDARY) (Note 1)
BT901 1-780-858-11 TERMINAL BOARD BATTERY
C901 1-118-630-11 CAP, ALUMINIUM ELECT 48uF 330V
#9 3-078-890-21 SCREW, TAPPING
#140 2-635-562-01 SCREW (M1.7)
DISASSEMBLY
1. Remove in numerical order (
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇: Solder
#9 X 1
2
Back View
Screw
#9: M1.7 X 5.0 (Tapping) #140: M1.7X 2.0
(Silver)
3-078-890-21
(Claw)
1.7
BT901
115
5.0
Note
Note 1: Replace the battery holder (BH001) together when
replacing the lithium storage battery (BT001) on the RL
Service Block Assy.
ns
(The battery holder removed once cannot be used
116
again.)
When mounting these parts, mount new battery holder
first and attach new lithium storage battery next.
Note 2: • When installing the ST-1019 Flexible Board, fold it in
correct direction.
For how to fold the ST-1019 Flexible Board, refer to
"Assembly-1: Installation Method of ST-1019 Flexible
Board".
• If the ST-1019 Flexible Board is folded in incorrect
direction, replace it with a new one.
Re-folding the incorrectly folded ST-1019 Flexible
Board in opposite direction may cause disconnection
of the Flexible Board.
Note 3: Do not reuse the these sheets because its adhesive
force decreases when it is removed once.
2-6
to ) in the left figure.
1 4
#9 X 5
3
#9 Back View
#9
#9
(Black)
2-635-562-01
1.7
2.0
Note 1: RL Service Block Assyのリチウム蓄電池 (BT001) を交換
する場合はバッテリホルダ (BH001) も同時に新品に交換
してください。
(一度使用したバッテリホルダは再使用できません。)
部品取り付けの際は，先にバッテリホルダを取り付けてか
らリチウム蓄電池を装着してください。
Note 2: ・ ST-1019フレキシブル基板の取り付け時，折り目の方向
を間違えないように注意してください。
折り目の付け方については"Assembly-1: Installation
Method of ST-1019 Flexible Board"を参照してくださ
い。
・ もし間違った方向に折ってしまった場合は，新品のST-
1019 フレキシブル基板に交換してください。
間違えて折り目を付けてしまったフレキシブル基板を逆
方向に折り直すと，フレキシブル基板が断線してしまう
恐れがあります。
Note 3: これらのシートは一度剥がすと粘着力が弱くなるため，
再利用はしないでください。
Remove the Imager
4
Block Section