Craftsman INCREDI-PULL 316.791930 Operator's Manual page 8

CHECKING THE OIL LEVEL
WARNING:
To avoid serious personal injury, always turn
your unit off and allow it to cool before you clean or service it.
The importance of checking and maintaining the proper oil level in the
crankcase cannot be overemphasized. Check oil before each use:
1. Stop the engine and allow
oil to drain into the
crankcase.
2. Place the engine on a flat,
level surface with the
cutting head shield
hanging off a work bench
or table to get a proper oil
level reading (Fig. 17).
3. Keep dirt, grass clippings
and other debris out of the
engine. Clean the area
around the oil fill plug
before removing it.
4. Remove the oil fill plug.
5. Look into the oil fill hole;
use a flashlight if needed.
The oil should be just
touching the inner most
thread (Fig. 18).
6. If the oil level is not
touching the inner most
thread on the oil fill hole,
add a small amount of oil to
the oil fill hole and recheck
(Fig. 18). Repeat this
procedure until the oil level
reaches the innermost
thread on the oil fill hole.
NOTE: Do not overfill the unit.
NOTE: Make sure the O-ring
is in place on the oil fill
plug when checking
and changing the oil (Fig. 19).
CHANGING THE OIL
CAUTION:
Wear gloves to prevent injury when handling
the unit.
For a new engine, change the
oil after the first 10 hours of
operation. Change the oil
while the engine is still warm.
The oil will flow freely and
carry away more impurities.
1. Remove the oil fill plug.
2. Pour the oil out of the oil
fill hole and into a
container by tipping the
unit to a vertical position
(Fig. 20). Allow ample
time for complete
drainage.
3. Wipe up any oil residue
on the unit and clean up
any oil that may have
spilled. Dispose of the oil
according to Federal,
State and local
regulations.
4. Refill the crankcase with 3.04 fluid ounce (90 ml) of SAE 30 SF,
SG, SH oil.
MAINTENANCE & REPAIR INSTRUCTIONS
Fig. 17
Add 1.4-1.5 Oz. Oil Fill Hole
(41-44 ml)
Oil Full Line
Fig. 18
Oil Fill Plug
O-Ring
Oil Fill
Hole
Fig. 19
Fig. 20
Fig. 21
NOTE: Use the bottle and
spout saved from
initial use to measure
the correct amount of
oil. The top of the
label on the bottle
measures
approximately 3.04
ounces (90 ml) (Fig.
22). Check the level,
See Checking the Oil
Level. If the level is low, add a small amount of oil and
recheck. Do not overfill (Fig. 21).
5. Replace the oil fill plug.
6. Reconnect the spark plug boot.
AIR FILTER MAINTENANCE
WARNING:
To avoid serious personal injury, always turn
the unit off and allow it to cool before you clean or service it.
Cleaning the Air Filter
Clean and re-oil the air filter
every 10 hours of operation. It
is an important item to
maintain. Failure to maintain
the air filter properly can result
in poor performance or can
cause permanent damage to
the engine.
1. Open the air filter cover.
Push the tab on the under
side of the cover inward.
Then pull the air filter
cover out and up. (Fig. 23).
2. Remove the air filter
(Fig. 27).
3. Wash the filter in detergent
and water (Fig. 24). Rinse
the filter thoroughly and
allow it to dry.
4. Apply enough clean SAE
30 motor oil to lightly coat
the filter (Fig. 25).
5. Squeeze the filter to
spread and remove
excess oil (Fig. 26).
6. Replace the filter (Fig. 27).
NOTE: If the unit is operated
without the air filter,
you will VOID the
warranty.
7. Reinstall the air filter
cover. Position the slots
on the top of the air filter
cover onto the tabs at the
top of the back plate
(Fig. 23).
8. Swing the cover down
until the tab on the air
filter backplate snaps into
place in the slot on the air
filter cover (Fig. 23).
8
Fill Line
Fig. 22
Air Filter Cover
Air Filter
Tab
Fig. 23
Fig. 24
Fig. 25
Fig. 26
Tabs
Back
Plate
Air Filter
Locking Tab
Fig. 27