Setting The Surround Setup; When Selecting The Source Direct; When Selecting The Cinema Eq; When Selecting The Decoding Mode - LG LGAV410 Owner's Manual

Setting the Surround Setup

x x Notes:
Only when the digital input is selected as signal
l l
input, the decoding mode as well as the surround
mode can be selected as desired.
When the analog input is selected, only the surround
l l
mode can be selected as desired.
Press the CURSOR UP(
1
select the desired item.
Each time these buttons are pressed, "
l l
are moved to the corresponding mode.
Press the CURSOR LEFT(
2
to select the desired mode.
Each time these buttons are pressed, the modes
l l
change as follows according to the selected item :

When selecting the Source Direct

Only when playing program sources in analog stereo
l l
or digital 2 ch PCM format, the SOURCE DIRECT
can be selected.
On : Select this to achieve the pure sound quality.
When this is selected, the stereo mode is auto-
matically selected and the pure sound that
bypasses the tone circuitry will be heard.
Off : Select this to cancel the source direct function.
x x Notes:
When the SOURCE DIRECT is set to On, DECOD-
l l
ING MODE, surround mode and CINEMA EQ cannot
be selected.
When you select the 7.1 CH DIRECT as input source
l l
or the digital signals from DTS, Dolby Digital or
MPEG sources, etc. are input, the source direct func-
tion is automatically canceled.
To select the source direct function for
pure sound quality or not
To select the desired decoding mode
To select the desired surround mode
To select the cinema EQ function or not.
)/DOWN( ) buttons to
3 3 4 4
DVD
VOL. CH LEVEL
OSD CH SEL
ENTER
RPT INTRO
A B
TITLE
7.1 SURR RETURN
AUTO
DSP
MODE
ST
DISC TEST CENTER
P.SCAN TONE MODE
TUNER CD T1/MON AUX PHONO
VID1 VID2 VID3 VID4 VID5
SYS DISP SLEEP DIRECT IN ROOM2
" and " "
1 1 2 2
)/RIGHT( ) buttons
1 1 2 2
DVD
VOL. CH LEVEL
OSD CH SEL
ENTER
RPT INTRO
A B
TITLE
7.1 SURR RETURN
AUTO
DSP
MODE
ST
DISC TEST CENTER
P.SCAN TONE MODE
TUNER CD T1/MON AUX PHONO
VID1 VID2 VID3 VID4 VID5
SYS DISP SLEEP DIRECT IN ROOM2

When selecting the CINEMA EQ

When 96 kHz PCM(2 channel stereo) signals are
l l
input or the source direct function is selected, the
cinema EQ function can not be selected.
On : Select this to compensate for edgy or shrill
movie sound tracks.
Off : Select this to cancel the cinema EQ function.

When selecting the Decoding Mode

Depending on the input digital signal format, you can
select the desired decoding mode.
Auto : Select this for automatic detection of a digital
l l
input signal format.
The input digital signal format (DTS, Dolby
Digital, MPEG or PCM(2 channel stereo), etc.)
used by the selected digital input source is
detected automatically to perform the
necessary decoding process for optimum sur-
round modes.
Dolby Digital : Select this for Dolby Digital signal
l l
processing. The decoding process is
preformed only when Dolby Digital
signals are input.
DTS : Select this for DTS signal processing. The
l l
decoding process is performed only when DTS
signals are input.
MPEG : Select this for MPEG signal processing. The
l l
decoding process is performed only when
MPEG signals are input.
PCM : Select this for PCM signal processing. The
l l
decoding process is performed only when
PCM signals are input.
x x Notes:
Surround sound effect will not work properly if the
l l
signal passes through a graphic equalizer.
Please refer to your equalizer operating instructions
for guidance on switching off(or defeating) the
equalizer.
Only when the digital input is selected as signal input
l l
for the input sources except TUNER and AUX, the
decoding mode can be selected.
Noise may be generated at the beginning of
l l
playback and while searching during DTS playback
in the auto mode. In this case, try playing in the DTS
mode.
3 5