Advertisement
Quick Links
Water Management System
Patent Pending
Owner's Manual
800378
1/13/16-LBRY
Manufactured by:
©2011-2016
HELLENBRAND, INC.
404 Moravian Valley Road
Waunakee, Wisconsin 53597
Phone: 608-849-3050 • Fax 608-849-7398
Web: www.hellenbrand.com • Email: info@hellenbrand.com
1
Advertisement
Related Manuals for Hellenbrand 109248
Summary of Contents for Hellenbrand 109248
- Page 1 Water Management System Patent Pending Owner’s Manual 800378 1/13/16-LBRY Manufactured by: ©2011-2016 HELLENBRAND, INC. 404 Moravian Valley Road Waunakee, Wisconsin 53597 Phone: 608-849-3050 • Fax 608-849-7398 Web: www.hellenbrand.com • Email: info@hellenbrand.com...
- Page 2 Congratulations on your purchase of the Hellenbrand Water Management System. This patented water reuse system recovers water that normally would be discharged to the drain and stores it and uses the water to flush the toilets, helping preserve our most precious natural resource, water. This owner’s manual is designed to assist owners and installers with the operation, maintenance, and installation of your new water reuse system.
- Page 5 INSTALLATION INSTRUCTIONS FOLLOW ALL STATE AND LOCAL PLUMBING CODES Place water softener and WMS storage tank on clean, level and solid location. Install softener according to installation instructions in softener manual. Run drain line from softener to Motorized Alternating Valve (MAV) on storage tank and run drain line from MAV to drain in pipe capable of handling softener backwash flow rate.
- Page 6 INSTALLATION INSTRUCTIONS (All electrical & plumbing should be done in accordance to all local codes) 4. A jumper ground wire should be installed between the • Do not use vaseline, oils, other hydrocarbon lubricants or spray inlet and outlet pipe whenever the metallic continuity of silicone anywhere.
- Page 7 WIRE MAV TO PM SERIES CONTROL WIRING OPTION 1: MAV Drive Cable must be connected to PC Board prior to programming or error 116 will result. If installing any place other than brine tank, allow 4” of clearance above for service access. After plumbing completed, next installation step is to provide access for MAV cable through back of valve.
- Page 8 THREE-WAY, 1” MAV-FNPT, PART NUMBER: 102032 Exploded Parts View Drawing No. Order No. Description 102032(F-F) 102033(M-M) 101471 MAV/NOHWBY COVER ASY 102095 WS MOTOR ASY 8 FT 106139 SCREW #8-3/4 PHPN T-25 SS 106133 WS1.5 & 2Alt/2BY REDUCGEARCVASY 101746 WS1 DRIVE GEAR 12X36 106134 WS2 BYPASS REDUCTION GEAR AXLE 106140...
- Page 9 THREE-WAY, 1.5” MAV, PART NUMBER: 105988 Exploded Parts View Drawing No. Order No. Description 105988 15-V3071BSPT 101471 MAV / NOHWBY COVER ASSY 102095 WS MOTOR ASY 8 FT 106139 SCREW #8-3/4 PHPN T-25 SS 106133 WS1.5&2ALT/2BY REDUCGEARCVRASY 101746 WS1 DRIVE REDUCING GEAR 12X36 106134 WS2 BYPASS REDUCTION GEAR AXLE 106140...
- Page 10 WATER MANAGEMENT SYSTEM PROGRAMMING: Press and arrows to select desired option. Press NEXT to go to next step (Press REGEN to go to previous step) Press NEXT & for 3 seconds or until display changes. Release and Press NEXT & for 3 seconds again until valve type is displayed.
- Page 11 DELIVERY PUMP OPTION: Part No. Description 107368 4.90 GPM open flow – QD ports – 60 PSI – 115 volt with cord 2.15 GPM @ 40 PSI - 115 Volt AQUATECH WATER PUMPS 550 Series Super Flow Pump Key Operational Benefits: •...
- Page 12 DELIVERY PUMP OPTION: Description 6PM @ 49 / 12GPM @ 36 PSI GRUNDFOS MQ - MQ 3-45 Compact, all-in-one unit for your home water supply Easy to select Unique user benefits The Grundfos MQ is a compact pump and pressure The Grundfos MQ “anti-cycling”...
- Page 13 tank is a 100% butyl rubber diaphragm that has been • Enhanced bottom dome post cured to eliminate any unwanted taste and odors. Combined with a polypropylene liner it keeps system PRESSURE TANKS FOR DELIVERY SYSTEM • NSF Standard 58 water contained in a sealed water chamber.
- Page 14 1/2” Tube x MNPT ADPT WR-360 109799 100622 1-1/4" x CL Nipple TxT *103698 (PVC-80) is not approved for potable use in the state of WI Exploded view for 103695/103696/103967/103968 Dwg #: 800144 Hellenbrand 04/06/2005 Rev 3-9-11 AGM Waunakee, WI J.MILLER (608)849-3050...
- Page 15 FLOAT ASSEMBLY, P ART NUMBER 109148...
- Page 17 18-INCH ROUND BRINE TANKS 18 inch blow molded round brine tanks offer a refreshing look in the residential and light commercial tank field. Durable materials and the latest in plastic processing technology provide trouble-free performance. Ultraviolet inhibitors (UVI) are now standard in all tanks except black, which has a natural resistance to the sun's rays.
- Page 18 24” AND 30” COMMERCIAL/INDUSTRIAL BLOW MOLDED TANKS Hellenbrand now offers both 24" and 30" round blow molded tanks. The introduction of the 30" diam- eter tank makes it the largest blow molded tank for commercial/indus- trial applications. Like the 24" round tank, the 30"...