Remote Control; General - Insignia NS24D310NA17OM User Manual

Remote control

Problem Solution
Remote
• Make sure that the power cord is
control does
plugged into a working outlet.
not work.
• Make sure that there are no
obstructions between the remote
control and the remote control
sensor on the front of the TV.
• Point the remote control directly at
the remote control sensor on your
TV. For the location of the remote
control sensor, see
remote control
• The supplied batteries are wrapped
tightly in clear plastic. Make sure
that you have removed this plastic
from the batteries.
• Make sure that the batteries are
installed correctly. See
remote control batteries
page 28.
• Replace dead batteries with new
batteries. See
control batteries
Trouble
• See instructions and a table of
programming
common codes in
your existing
universal remote controls
universal
page 29.
remote
• Codes are subject to change. For
control.
up-to-date codes, go to
universal remote control codes
page 29, or visit
www.insigniaproducts.com/remotecodes
• Replace dead batteries with new
batteries.
• Refer to the User Guide that
accompanied your universal remote
control and contact the
manufacturer if problems persist.

General

Problem Solution
No power.
• Make sure that the power cord is
plugged into a working outlet.
• Unplug the power cord, wait 60
seconds, then plug the cord back in
and turn on your TV.
• Other devices (for example, a
surround sound receiver, external
speakers, fans, or hair dryers) may
be interfering with your TV. Try
turning off one device at a time to
determine which device is causing
interference. After you have
determined which device is causing
interference, move it further from
the TV to eliminate the interference.
64
Aiming the
on page 28.
Installing
on
Installing remote
on page 28.
Programming
on
Viewing
on
www.insigniaproducts.com
Problem Solution
"No signal"
• Press INPUT and make sure that you
error message
have selected the correct input for
is displayed.
the device or service you are trying
to use.
• If you are using a cable or satellite
box, use the remote that came with
that box to change channels.
After Auto
• Reception can vary by channel
Channel
depending on the broadcast power
Search, there
level of a given station. Contact your
are no
cable or satellite TV provider.
channels.
• Make sure that the antenna or
cable/satellite TV is connected
securely to your TV.
• Try replacing the cable between the
antenna/cable or cable/satellite box
and your TV.
When I press
• Turn on the device. Your TV
INPUT, I
automatically detects and displays
cannot select
which video jacks have devices
my device (it is
connected to them when the
grayed out).
devices are turned on.
• Turn off Auto Input Sensing. See
Turning Input Sensor on or off
page 57.
One or more
• Make sure that the channels are not
channels do
blocked. See
not display.
control levels
• Make sure that the channels are not
hidden. The channel may have been
deleted from the channel list. You
can tune to the channel by pressing
the number buttons or you can add
the channel back to the channel list.
See
• If you are using a cable or satellite
box, use the remote that came with
that box to change channels.
• Press INPUT and make sure that you
have selected the correct input for
the device or service you are trying
to use.
• If you are using an antenna, the
digital channel signal may be low. To
check the digital channel signal
strength, see
signal strength
Password is
• Enter 9999 to access parental
lost.
controls, then set a new password.
See
password
Some settings
• If a setting is grayed, the setting is
cannot be
not available in the current video
accessed.
input mode (for example TV mode).
Change to a different video input
source. See
input source
NS-24D310NA17
Setting parental
on page 49.
Hiding channels on page 46.
Checking the digital
on page 47.
Setting or changing the
on page 48.
Selecting the video
on page 32.
on