Bosch Professional GBH 18V-36 C Original Instructions Manual page 16

16 | English
is likely to bend if allowed to rotate freely without contact-
ing the workpiece, resulting in personal injury.
Apply pressure only in direct line with the bit and do
u
not apply excessive pressure. Bits can bend, causing
breakage or loss of control, resulting in personal injury.
Additional safety information
Use suitable detectors to determine if there are hid-
u
den supply lines or contact the local utility company
for assistance. Contact with electric cables can cause
fire and electric shock. Damaging gas lines can lead to ex-
plosion. Breaking water pipes causes property damage.
Always wait until the power tool has come to a com-
u
plete stop before placing it down. The application tool
can jam and cause you to lose control of the power tool.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
In case of damage and improper use of the battery, va-
u
pours may be emitted. The battery can set alight or ex-
plode. Ensure the area is well ventilated and seek medical
attention should you experience any adverse effects. The
vapours may irritate the respiratory system.
Do not open the battery. There is a risk of short-circuit-
u
ing.
The battery can be damaged by pointed objects such
u
as nails or screwdrivers or by force applied externally.
An internal short circuit may occur, causing the battery to
burn, smoke, explode or overheat.
Only use the battery with products from the manufac-
u
turer. This is the only way in which you can protect the
battery against dangerous overload.
Protect the battery against heat, e.g. against
continuous intense sunlight, fire, dirt, water
and moisture. There is a risk of explosion and
short-circuiting.
Do not touch any application tools or adjacent housing
u
components shortly after operation. These can become
very hot during operation and cause burns.
The application tool may jam during drilling. Make
u
sure you have a stable footing and hold the power tool
firmly with both hands. Otherwise you could lose con-
trol of the power tool.
Take care when carrying out demolition work using
u
the chisel. Falling fragments of the demolition material
could injure you or any bystanders.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
Caution! When using the power tool with Bluetooth
u
fault may occur in other devices and systems, aero-
planes and medical devices (e.g. pacemakers, hearing
aids). Also, damage to people and animals in the im-
mediate vicinity cannot be completely excluded. Do
not use the power tool with Bluetooth
medical devices, petrol stations, chemical plants,
1 609 92A 70K | (09.11.2021)
areas with a potentially explosive atmosphere or in
blasting areas. Do not use the power tool with
Bluetooth
your body for extended periods.
The Bluetooth® word mark and logos are registered trade-
marks owned by Bluetooth SIG, Inc. and any use of such
marks by Robert Bosch Power Tools GmbH is under li-
cense.
Product Description and
Specifications
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for hammer drilling in concrete,
masonry and stone, as well as for light and medium difficulty
chiselling work.
With the Bluetooth
power tool data and settings can be transferred between the
power tool and a mobile device by means of Bluetooth
less technology.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
®
, a (15)
(16)
(17)
(18)
®
in the vicinity of
(19)
®
in aircraft. Avoid using the product near
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
®
Low Energy Module GCY 42 inserted,
SDS max drill chuck
SDS max tool holder
Dust protection cap
Locking sleeve
Combi switch for operating modes and clockwise/
anticlockwise rotation
Vibration damping
Lock-on button for on/off switch
Handle (insulated gripping surface)
On/off switch
a)
Battery
®
Cover for GCY 42 Bluetooth Low Energy Module
Worklight
Auxiliary handle (insulated gripping surface)
a)
Battery release button
User interface
Battery charge indicator (user interface)
Rapid shut-off indicator (KickBack control) (user
interface)
Working modes indicator (user interface)
Button to select the working mode (user interface)
®
wire-
Bosch Power Tools